SIST EN ISO 14122-3:2002/A1:2010

SLOVENSKI STANDARD
SIST EN ISO 14122-3:2002/A1:2010
01-december-2010
9DUQRVWVWURMHY6WDOQLGRVWRSLGRVWURMHYLQSRVWURMHQMGHO6WRSQLFH
VWRSQLþDVWHOHVWYHLQYDURYDOQHRJUDMH'RSROQLOR$,62$PG

Safety of machinery - Permanent means of access to machinery - Part 3: Stairs,
stepladders and guard-rails - Amendment 1 (ISO 14122-3:2001/Amd 1:2010)
Sicherheit von Maschinen - Ortsfeste Zugänge zu maschinellen Anlagen - Teil 3:
Treppen, Treppenleitern und Geländer (ISO 14122-3:2001/Amd 1:2010)
Sécurité des machines - Moyens d'accès permanents aux machines - Partie 3: Escaliers,
échelles à marches et garde-corps - Amendement 1 (ISO 14122-3:2001/Amd 1:2010)
1:2010)
Ta slovenski standard je istoveten z: EN ISO 14122-3:2001/A1:2010
ICS:
13.110 Varnost strojev Safety of machinery
SIST EN ISO 14122-3:2002/A1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14122-3:2002/A1:2010

---------------------- Page: 2 ----------------------

SIST EN ISO 14122-3:2002/A1:2010


EUROPEAN STANDARD
EN ISO 14122-3:2001/A1

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2010
ICS 13.110
English Version
Safety of machinery - Permanent means of access to machinery
- Part 3: Stairs, stepladders and guard-rails - Amendment 1 (ISO
14122-3:2001/Amd 1:2010)
Sécurité des machines - Moyens d'accès permanents aux Sicherheit von Maschinen - Ortsfeste Zugänge zu
machines - Partie 3: Escaliers, échelles à marches et maschinellen Anlagen - Teil 3: Treppen, Treppenleitern und
garde-corps - Amendement 1 (ISO 14122-3:2001/Amd Geländer - Änderung 1 (ISO 14122-3:2001/Amd 1:2010)
1:2010)
This amendment A1 modifies the European Standard EN ISO 14122-3:2001; it was approved by CEN on 14 April 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN Management Centre or to any CEN member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14122-3:2001/A1:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 14122-3:2002/A1:2010
EN ISO 14122-3:2001/A1:2010 (E)
Contents Page
Foreword .3
Annex ZA (informative)  Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC .4
Annex ZB (informative)  Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .5

2

---------------------- Page: 4 ----------------------

SIST EN ISO 14122-3:2002/A1:2010
EN ISO 14122-3:2001/A1:2010 (E)
Foreword
This document (EN ISO 14122-3:2001/A1:2010) has been prepared by Technical Committee ISO/TC 199
"Safety of machinery" in collaboration with Technical Committee CEN/TC 114 “Safety of machinery” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2010, and conflicting national standards shall be withdrawn at
the latest by October 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directives.
For relationship with EU Directives, see informative Annex ZA and ZB, which are integral parts of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 14122-3:2001/Amd 1:2010 has been approved by CEN as a EN ISO 14122-3:2001/A1:2010
without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 14122-3:2002/A1:2010
EN ISO 14122-3:2001/A1:2010 (E)
Annex ZA
(informative)


Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC
This International Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 98/37/EC, amended by 98/79/EC.

Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative Clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
relevant Essential Requirements 1.6.2, “Access to operating position and service points”, and 1.5.15, “Risks of
slipping, tripping or falling”, of that Directive and associated EFTA regulations.


WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.
4

---------------------- Page: 6 ----------------------

SIST EN ISO 14122-3:2002/A1:2010
EN ISO 14122-3:2001/A1:2010 (E)
Annex ZB
(informative)


Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This International Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC.

Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative Clauses of
this standard confe
...