SIST EN 845-1:2013/kFprA1:2015

SLOVENSKI STANDARD
SIST EN 845-1:2013/kFprA1:2015
01-december-2015
Specifikacija za dodatne komponente zidovja - 1. del: Vezna stremena, sidrni
trakovi, obešala in konzole
Specification for ancillary components for masonry - Part 1: Wall ties, tension straps,
hangers and brackets
Festlegungen für Ergänzungsbauteile für Mauerwerk - Teil 1: Maueranker, Zugbänder,
Auflager und Konsolen
Spécification pour composants accessoires de maçonnerie - Partie 1: Attaches, brides
de fixation, étriers de support et consoles
Ta slovenski standard je istoveten z: EN 845-1:2013/FprA1:2015
ICS:
91.060.10 Stene. Predelne stene. Walls. Partitions. Facades
Fasade
91.080.30 Zidane konstrukcije Masonry
SIST EN 845-1:2013/kFprA1:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 845-1:2013/kFprA1:2015

---------------------- Page: 2 ----------------------

SIST EN 845-1:2013/kFprA1:2015


FINAL DRAFT
EUROPEAN STANDARD
EN 845-1:2013
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
October 2015
ICS 91.080.30
English Version

Specification for ancillary components for masonry - Part
1: Wall ties, tension straps, hangers and brackets
Spécification pour composants accessoires de Festlegungen für Ergänzungsbauteile für Mauerwerk -
maçonnerie - Partie 1: Attaches, brides de fixation, Teil 1: Maueranker, Zugbänder, Auflager und Konsolen
étriers de support et consoles
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 125.

This draft amendment A1, if approved, will modify the European Standard EN 845-1:2013. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 845-1:2013/FprA1:2015:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
Contents Page
European foreword . 3
1 Modification to Table 1 . 4
2 Modification to Clause 8. 5
3 Modification to Annex ZA . 11

2

---------------------- Page: 4 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
European foreword
This document (EN 845-1:2013/FprA1:2015) has been prepared by Technical Committee CEN/TC 125
“Masonry”, the secretariat of which is held by BSI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
3

---------------------- Page: 5 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
1 Modification to Table 1
Replace the existing Table 1 with the new one.
"Table 1 — Information to be provided
a
Informatio Information to be supplied Cavity Shear Slip Tension Joist Brackets
n reference wall ties ties straps hangers
number ties
1 Material/coating specification in
✓ ✓ ✓ ✓ ✓ ✓
accordance with Table A.1 and steel grade
relevant to product type.
2 Dimensions in accordance with 5.2 in mm
✓ ✓ ✓ ✓ ✓ ✓
3 Declared minimum embedment length in ✓ ✓ ✓ – ✓
mm
4 Declared value of tensile load capacity in N ✓ ✓ – ✓ – –
and failure mode
5 Declared value of compressive load ✓ ✓ – – – –
capacityin N and failure mode
6 Declared value of shear load capacity and – – – –
✓ ✓
failure mode in N
7 Declared value of vertical load capacity in – – – –
✓ ✓
N and failure mode
8 Declared mean displacement/deflection in
✓ ✓ ✓ ✓ ✓ ✓
mm
9 Whether the component is symmetrical or ✓ ✓ ✓ ✓ – –
asymmetrical
10 Whether the component is slope-tolerant , ✓ – – – – –
and if it is, the range of difference in level
from the outer leaf down to the inner leaf,
over which it may be used in mm
11 Whether the component is movement ✓ – – – –
tolerant together with the maximum
permissible movement range in mm
12 Whether a component is intended to be
✓
resistant to water crossing the cavity

13 Specification for use, including limiting
✓ ✓ ✓ ✓ ✓ ✓
requirements on compressive strength
and types of masonry units and mortars,
the type, size, number and location of any
fixings and any particular assembly or
installation instructions
14 Product identity (see Clause 7 c))
✓ ✓ ✓ ✓ ✓ ✓
15 Minimum mortar joint thickness in mm for ✓ ✓ ✓ ✓ ✓ –
which the component is suitable (where
relevant)
16 The specification of any fixing devices not ✓ ✓ ✓ ✓ ✓ ✓
provided by the manufacturer and not
packaged with the product
a
Additional information may include sound attenuation, thermal characteristics and instructions regarding safety during
installation.
✓ To be provided
– Not required
"
4

---------------------- Page: 6 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
2 Modification to Clause 8
Delete Clause 8 entirely and replace it with the following:
"8 Assessment and verification of constancy of performance - AVCP
8.1 General
The compliance of wall ties, tension straps, hangers and brackets with the requirements of this
standard and with the performances declared by the manufacturer in the DoP shall be demonstrated
by:
- determination of the product type;
- factory production control by the manufacturer, including product assessment.
The manufacturer shall always retain the overall control and shall have the necessary means to take
responsibility for the conformity of the product with its declared performance(s).
NOTE The assignment of tasks to the notified body(ies) and the manufacturer is shown in Table ZA.2.
8.2 Type testing
8.2.1. General
All performances related to characteristics included in this standard shall be determined when the
manufacturer intends to declare the respective performances unless the standard gives provisions for
declaring them without performing tests. (e.g. use of previously existing data, and conventionally
accepted performance).
Assessment previously performed in accordance with the provisions of this standard, may be taken into
account provided that they were made to the same or a more rigorous test method, under the same
AVCP system on the same product or products of similar design, construction and functionality, such
that the results are applicable to the product in question.
Note: Same AVCP system means testing by an independent third party, under the responsibility of a
notified product certification body
For the purposes of assessment, the manufacturer's products may be grouped into families, where it is
considered that the results for one or more characteristics from any one product within the family are
representative for that same characteristic for all products within that same family
In addition, the determination of the product type shall be performed for all characteristics included in
the standard for which the manufacturer declares the performance:
- at the beginning of the production of a new or modified wall tie, tension strap, hanger and bracket
(unless a member of the same product range), or
- at the beginning of a new or modified method of production (where this may affect the stated
properties);
or
5

---------------------- Page: 7 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
- they shall be repeated for the appropriate characteristic(s), whenever a change occurs in the wall
tie, tension strap, hanger and bracket design, in the raw material or in the supplier of the components,
or in the method of production (subject to the definition of a family), which would affect significantly
one or more of the characteristics.
Where components are used whose characteristics have already been determined, by the component
manufacturer, on the basis of assessment methods of other product standards, these characteristics
need not be re-assessed. The specifications of these components shall be documented.
Products bearing regulatory marking in accordance with appropriate harmonized European
specifications may be presumed to have the performances declared in the DoP, although this does not
replace the responsibility on the wall tie, tension strap, hanger and bracket manufacturer to ensure that
the wall tie, tension strap, hanger and bracket as a whole is correctly manufactured and its component
products have the declared performance values.
8.2.2 Test samples, testing and compliance criteria
The minimum sample size for a single test shall be as given in Table 2 and shall be drawn at random.
For initial type testing, the batch from which the sample is drawn shall be of a size of at least 100 times
the number of specimens taken. Pre-production samples may be used for initial type tests where it is
possible to demonstrate that the characteristics of performance are representative of products from the
full production process.
Table 2 — Sampling - Number of specimens
a
Product Minimum number per single test
a,b
Wall ties designed to link two leaves of a cavity 10
wall or cladding to a frame
b
Shear ties

10
b
Slip ties
10
Joist hangers 5
Brackets 5
Tension-straps 5 per end
a
 For testing organic coatings, see sampling requirements of EN 846-13.
b
These quantities will be doubled where both ends of asymmetrical wall ties are tested

separately.

In the event of the need to check the compliance of a lot or consignment of a product supplied to site or
installed, a sample shall be taken at random from the lot or consignment and tested. The sample sizes
shall be not less than those given in Table 2.
6

---------------------- Page: 8 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
8.2.3 Test reports
The results of the determination of the product type shall be documented in test reports. All test reports
shall be retained by the manufacturer for at least 10 years after the last date of production of the wall
tie, tension strap, hanger and bracket to which they relate.
8.2.4 Shared other party results
NOTE The sharing of other party results is in principle applicable to all systems of assessment and evaluation
of constancy of performance.
A manufacturer may use the results of the product type determination obtained by someone else (e.g.
by another manufacturer, as a common service to manufacturers, or by a product developer), to justify
his own declaration of performance regarding a product that is manufactured according to the same
design (e.g. dimensions) and with raw materials, constituents and manufacturing methods of the same
kind, provided that:
– the results are known to be valid for products with the same essential characteristics relevant for
the product performance;
– in addition to any information essential for confirming that the product has such same
performances related to specific essential characteristics, the other party who has carried out the
1
determination of the product type concerned or has had it carried out, has expressly accepted to
transmit to the manufacturer the results and the test report to be used for the latter’s product type
determination, as well as information regarding production facilities and the production control
process that can be taken into account for FPC;
– the manufacturer using other party results accepts to remain responsible for the product having
the declared performances and he also:
– ensures that the product has the same characteristics relevant for performance as the one that has
been subjected to the determination of the product type, and that there are no significant differences
with regard to production facilities and the production control process compared to that used for the
product that was subjected to the determination of the product type; and
– keeps available a copy of the determination of the product type report that also contains the
information needed for verifying that the product is manufactured according to the same design and
with raw materials, constituents and manufacturing methods of the same kind.
8.3 Factory production control (FPC)
8.3.1 General
The manufacturer shall establish, document and maintain an FPC system to ensure that the products
placed on the market comply with the declared performance of the essential characteristics.
The FPC system shall consist of procedures, regular inspections and tests and/or assessments and the
use of the results to control raw and other incoming materials or components, equipment, the
production process and the product.
All the elements, requirements and provisions adopted by the manufacturer shall be documented in a
systematic manner in the form of written policies and procedures.
7

---------------------- Page: 9 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
This factory production control system documentation shall ensure a common understanding of the
evaluation of the constancy of performance and enable the achievement of the required product
performances and the effective operation of the production control system to be checked. Factory
production control therefore brings together operational techniques and all measures allowing
maintenance and control of the compliance of the product with the declared performances of the
essential characteristics.
In case the manufacturer has used shared product type results, the FPC shall also include the
appropriate documentation as foreseen in 8.2.4.
8.3.2 Requirements
8.3.2.1 General
The manufacturer is responsible for organizing the effective implementation of the FPC system in line
with the content of this product standard. Tasks and responsibilities in the production control
organization shall be documented and this documentation shall be kept up-to-date.
The responsibility, authority and the relationship between personnel that manages, performs or verifies
work affecting product constancy, shall be defined. This applies in particular to personnel that need to
initiate actions preventing product non-constancies from occurring, actions in case of non-constancies
and to identify and register product constancy problems.
Personnel performing work affecting the constancy of performance of the product shall be competent
on the basis of appropriate education, training, skills and experience for which records shall be
maintained.
In each factory the manufacturer may delegate the action to a person having the necessary authority to:
— identify procedures to demonstrate constancy of performance of the product at appropriate stages;
— identify and record any instance of non-constancy;
— identify procedures to correct instances of non-constancy.
The manufacturer shall draw up and keep up-to-date documents defining the factory production
control. The manufacturer's documentation and procedures should be appropriate to the product and
manufacturing process. The FPC system should achieve an appropriate level of confidence in the
constancy of performance of the product. This involves:
— the preparation of documented procedures and instructions relating to factory production
control operations, in accordance with the requirements of the technical specification to which
reference is made;
— the effective implementation of these procedures and instructions;
— the recording of these operations and their results;
— the use of these results to correct any deviations, repair the effects of such deviations, treat any
resulting instances of non-conformity and, if necessary, revise the FPC to rectify the cause of
non-constancy of performance.
Where subcontracting takes place, the manufacturer shall retain the overall control of the product and
ensure that he receives all the information that is necessary to fulfil his responsibilities according to this
European Standard.
8

---------------------- Page: 10 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
If the manufacturer has part of the product designed, manufactured, assembled, packed, processed
and/or labeled by subcontracting, the FPC of the subcontractor may be taken into account, where
appropriate for the product in question.
The manufacturer who subcontracts all of his activities may in no circumstances pass the above
responsibilities on to a subcontractor.
NOTE Manufacturers having an FPC system, which complies with EN ISO 9001 and which addresses the
provisions of the present European Standard are considered as satisfying the FPC requirements of the Regulation
(EU) No 305/2011.
8.3.2.2 Equipment
8.3.2.2.1 Testing
All weighing, measuring and testing equipment shall be calibrated and regularly inspected according to
documented procedures, frequencies and criteria.
8.3.2.2.2 Manufacturing
All equipment used in the manufacturing process shall be regularly inspected and maintained to ensure
use, wear or failure does not cause inconsistency in the manufacturing process. Inspections and
maintenance shall be carried out and recorded in accordance with the manufacturer’s written
procedures and the records retained for the period defined in the manufacturer's FPC procedures.
8.3.2.3 Raw materials and components
As appropriate, the manufacturer shall define the acceptance criteria of raw materials and the
procedures operated to ensure that these are met.
8.3.2.4 Controls during manufacturing process
The manufacturer shall plan and carry out production under controlled conditions.
8.3.2.5 Product testing and evaluation
The manufacturer shall establish procedures to ensure that the stated values of the characteristics he
declares are maintained. The characteristics, and the means of control, are:
1) material properties (organic coating impact, abrasion and corrosion resistance only)
(see Table A.2)
2) dimensions and permissible deviations in accordance with 5.2 shall be measured
3) tensile load capacity shall be subject to the tests indicated in 5.3.1.2, 5.3.1.3 and 5.3.4.2, see
Annex B;
4) compressive load capacity shall be subject to the tests indicated in 5.3.1.2 and 5.3.1.3, see
Annex B;
5) shear load capacity shall be subject to the tests indicated in 5.3.1.3, 5.3.1.4 and 5.3.1.5, see
Annex B;
6) vertical load capacity according to product type shall be subject to the tests indicated in 5.3.2
and 5.3.3, see Annex B.
9

---------------------- Page: 11 ----------------------

SIST EN 845-1:2013/kFprA1:2015
EN 845-1:2013/FprA1:2015 (E)
Displacement/Deflection (as appropriate) at one third of the declared value of mean load capacity shall
be subject to the tests indicated in 5.3.1.2, 5.3.1.3, 5.3.1.4, 5.3.2.3, 5.3.3.3 and 5.3.4.3, see Annex B.
Alternative methods of test to the methods referenced in this European Standard may be adopted
except for the initial type test and in cases of dispute, provided that these alternative methods satisfy
the following:
— a relationship can be shown to exist between the results from the referenced test and those from
the alternative test; and
— the information on which the relationship is based is available.
8.3.2.6 Non-complying products
The manufacturer shall have written procedures which specify how non-complying products shall be
dealt with. Any such events shall be recorded as they occur and these records shall be kept for the
period defined in the manufacturer’s written procedures.
Where the product fails to satisfy the acceptance criteria, the provisions for non-complying products
shall apply, the necessary corrective action(s) shall immediately be taken and the products or batches
not complying shall be isolated and properly identified.
Once the fault has been corrected,
...