SIST EN 10245-4:2003

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stahldraht und Drahterzeugnisse - Organische Beschichtungen auf Stahl-draht - Teil 4: Polyester-beschichteter DrahtFils et produits tréfilés en acier - Revetements organiques sur fils - Partie 4 : Fils a revetement de polyesterSteel wire and wire products - Organic coatings on steel wire - Part 4: Polyester coated wire77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chains25.220.60Organske prevlekeOrganic coatingsICS:Ta slovenski standard je istoveten z:EN 10245-4:2003SIST EN 10245-4:2003en01-november-2003SIST EN 10245-4:2003SLOVENSKI
STANDARD



SIST EN 10245-4:2003



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10245-4April 2003ICS 25.220.60; 77.140.65English versionSteel wire and wire products - Organic coatings on steel wire -Part 4: Polyester coated wireFils et produits tréfilés en acier - Revêtements organiquessur fils - Partie 4: Fils à revêtement de polyesterStahldraht und Drahterzeugnisse - OrganischeBeschichtungen auf Stahl-draht - Teil 4: Polyester-beschichteter DrahtThis European Standard was approved by CEN on 28 February 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10245-4:2003 ESIST EN 10245-4:2003



EN 10245-4:2003 (E)2ContentsForeword.3Introduction.41Scope.52Normative references.53Terms and definitions.54Methods of application of polyester coatings.65Requirements and testing methods for polyester coating material.65.1General.65.2Composition and method of application.65.3Consistency.65.4Density.65.5Hardness.75.6Tensile strength.75.7Elongation.76Requirements and test methods for polyester coating on wire and wire products.76.1General.76.2Appearance.76.3Colour.76.4Gloss.76.5Thickness.86.6Elongation.86.7Concentricity.86.8Adherence.87Performance requirements and tests for the polyester coating on the finished wire and wireproducts.97.1General.97.2Colour stability (accelerated weathering).97.3Kesternich test.97.4Boiling water test.98Retests.99Inspection and quality assurance.10Bibliography.11SIST EN 10245-4:2003



EN 10245-4:2003 (E)3ForewordThis document (EN 10245-4:2003) has been prepared by Technical Committee ECISS/TC 30 "Steel wire", thesecretariat of which is held by BSI.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by October 2003, and conflicting national standards shall be withdrawn at the latestby October 2003.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 10245-4:2003



EN 10245-4:2003 (E)4IntroductionThis European Standard for Organic coatings for steel wire is in a number of parts; Part 1 covering therequirements of a general nature and applying also to coatings for which no specific requirements have beenestablished in the subsequent parts of this standard.The subsequent parts of this standard deal more specifically with clearly defined coatings or groups of coatings.These coatings may have their own particular methods of application and their individual requirements which arespecified in these parts of this standard, in other standards or in manufacturers data sheets.This standard is made up of the following parts:Part 1: General rulesPart 2: PVC coated wirePart 3: PE coated wirePart 4: Polyester coated wireIn writing this series of standards consideration has been given to the nomenclature and transformation of organicmaterials as applied to steel wire. These organic coating materials may on application to wire and by theirintegration into the finished wire product change their characteristics and properties.This standard specifies characteristics and tests not only for the organic coating but also for the coating materialsboth before and after their application to steel wire and wire products. In addition it specifies the requirements forperformance tests and testing methods on organic coating material which have become an integral and permanentpart of the finished wire product. Therefore it has proven not to be practical to put all requirements in one clauseand all the tests in another one.To aid continuity and in order to limit complexity following structure has been chosen for this standard.Clause 5 deals with the characteristics and testing methods of organic coating material as supplied by themanufacturer for the purpose of its application to the wire. Tests described in this section are intended to be carriedout by the organic coating material manufacturer or the applicator before the coating operation.Clause 6 relates to the characteristics and testing methods for the "organic coating" when the organic coatingmaterial has been applied to and has become an integral part of the finished wire. Consequently tests are intendedto be in the main carried out by the coating "applicator".Clause 7 defines the Performance requirements and testing methods on the "organic coating" of the finished wire.When testing on the finished wire is not possible, tests will be carried out on "coated" panels.SIST EN 10245-4:2003



EN 10245-4:2003 (E)51 ScopeComplementary to EN 10245-1, this document specifies the characteristics and requirements for steel wire andwire products coated with polyester.It covers both thermoplastic and thermosetting polyester.2 Normative referencesThis European Standard incorporates by dated and undated reference, provisions from other publications. Thenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordate references, subsequent amendments to or revisions of any of the publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undate
...