SIST EN 1218-4:2004/A1:2006

SLOVENSKI STANDARD
SIST EN 1218-4:2004/A1:2006
01-julij-2006
9DUQRVWOHVQRREGHORYDOQLKVWURMHY±6WURML]DL]GHORYDQMHþHSRYLQXWRURYGHO
5REQHOHSLONH]YHULåQLPSRGDMDQMHP
Safety of woodworking machines - Tenoning machines - Part 4: Edge banding machines
fed by chain(s)
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen -
Teil 4: Kantenanleimmaschinen mit Kettenbandvorschub
Sécurité des machines pour le travail du bois - Tenonneuses - Partie 4 : Machines a
plaquer sur chant a chaîne(s)
Ta slovenski standard je istoveten z: EN 1218-4:2004/A1:2005
ICS:
79.120.10
SIST EN 1218-4:2004/A1:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 1218-4:2004/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 79.120.10

English Version
Safety of woodworking machines - Tenoning machines - Part 4:
Edge banding machines fed by chain(s)
Sécurité des machines pour le travail du bois - Sicherheit von Holzbearbeitungsmaschinen -
Tenonneuses - Partie 4 : Machines à plaquer sur chant à Zapfenschneid- und Schlitzmaschinen - Teil 4:
chaîne(s) Kantenanleimmaschinen mit Kettenbandvorschub
This amendment A1 modifies the European Standard EN 1218-4:2004; it was approved by CEN on 29 September 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1218-4:2004/A1:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 1218-4:2004/A1:2005 (E)
Foreword
This European Standard (EN 1218-4:2004/A1:2005) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 1218-4:2004 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by May 2006, and conflicting national
standards shall be withdrawn at the latest by May 2006.
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Di
...