SIST EN 3375-001:2018

SLOVENSKI STANDARD
SIST EN 3375-001:2018
01-november-2018
1DGRPHãþD
SIST EN 3375-001:2009
$HURQDYWLND(OHNWULþQLNDEOL]DGLJLWDOQLSUHQRVSRGDWNRYGHO7HKQLþQD
VSHFLILNDFLMD
Aerospace series - Cable, electrical, for digital data transmission - Part 001: Technical
specification
Luft- und Raumfahrt - Elektrische Leitungen für Digitaldatenübertragungen - Teil 001:
Technische Lieferbedingungen
Série aérospatiale - Câbles électriques pour transmission de données numériques -
Partie 001 : Spécification technique
Ta slovenski standard je istoveten z: EN 3375-001:2018
ICS:
29.060.20 Kabli Cables
49.060 /HWDOVNDLQYHVROMVND Aerospace electric
HOHNWULþQDRSUHPDLQVLVWHPL equipment and systems
SIST EN 3375-001:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 3375-001:2018

---------------------- Page: 2 ----------------------

SIST EN 3375-001:2018


EN 3375-001
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2018
EUROPÄISCHE NORM
ICS 49.090 Supersedes EN 3375-001:2007
English Version

Aerospace series - Cable, electrical, for digital data
transmission - Part 001: Technical specification
Série aérospatiale - Câbles électriques pour Luft- und Raumfahrt - Elektrische Leitungen für
transmission de données numériques - Partie 001 : Digitaldatenübertragungen - Teil 001: Technische
Spécification technique Lieferbedingungen
This European Standard was approved by CEN on 6 November 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3375-001:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 3375-001:2018
EN 3375-001:2018 (E)
Contents Page
European foreword . 3
1 Scope . 3
2 Normative references . 4
3 Terms and definitions . 4
4 Materials and construction of cables . 5
5 Required characteristics . 6
6 Tests methods . 6
7 Quality assurance . 11
8 Identification and marking . 12
9 Packaging, labelling and delivery lengths . 13

2

---------------------- Page: 4 ----------------------

SIST EN 3375-001:2018
EN 3375-001:2018 (E)
European foreword
This document (EN 3375-001:2018) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards shall
be withdrawn at the latest by February 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 3375-001:2007.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 3375-001:2018
EN 3375-001:2018 (E)
1 Scope
This European Standard specifies the required characteristics, test methods, qualification and acceptance
conditions of signal data transmission electrical cables.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2083, Aerospace series — Copper and copper alloys conductors for electrical cables — Product standard
EN 2084, Aerospace series — Cables, electrical, general purpose, with conductors in copper or copper
alloy — Technical specification
EN 2235, Aerospace series — Single and multicore electrical cables, screened and jacketed — Technical
specification
*
EN 3475-100 , Aerospace series —Cables, electrical, aircraft use — Test methods — Part 100: General
EN 3838, Aerospace series — Requirements and tests on user-applied markings on aircraft electrical cables
EN 4434, Aerospace series — Copper or copper alloy lightweight conductors for electrical cables — Product
standard (Normal and tight tolerances)
EN 9133, Aerospace series —Quality Management Systems — Qualification Procedure for Aerospace
1)
Standard Products
ISO 2574, Aircraft — Electrical cables — Identification marking
ISO 8815, Aircraft — Electrical cables and cable harnesses — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8815 and EN 3475-100 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp

*
And all parts quoted in this European Standard.
1) At draft stage.
4

---------------------- Page: 6 ----------------------

SIST EN 3375-001:2018
EN 3375-001:2018 (E)
4 Materials and construction of cables
4.1 General
The composition, dimensions and mass of the cable shall conform to the characteristics below, as well as
the values specified in the product standards.
The individual cores shall conform to EN 2083 or EN 4434, EN 2084 and the product standards.
4.2 Materials
The materials shall conform to the product standard.
The surface of conductive materials used shall be free from corrosion and other contamination.
Insulation and others materials shall have no corrosive effect upon the conductors and screens and shall
not be susceptible to attack by mould and other microorganisms.
4.3 Construction of cables
4.3.1 General
The permissible operating temperature of conductors shall not be lower than the maximum operating
temperature of the cable as a whole.
4.3.2 Cabled cores
The lay length of the outer lay shall not be less than eight (8) times and not more than 16 times the
nominal diameter of the cabled cores, except if a different value is necessary to maintain the required
characteristics.
The core shall not be spliced.
Where filler cores are used, this shall be specified in the product standard.
The assembly may be held together with an overall wrap.
4.3.3 Screened cables
4.3.3.1 General
The construction shall conform to the product standard.
Depending on protection level, the screening may be composed of:
• one (1) or several spiral layers;
• one (1) or several braids made using strands or strips;
• one (1) or several metallic or other strips;
• one (1) or several layers of extruded conductive or non-conductive materials;
• a combination of the above.
5

---------------------- Page: 7 ----------------------

SIST EN 3375-001:2018
EN 3375-001:2018 (E)
The screening may be individual and/or overall.
The individual strands or strips used for the screen shall be free from kinks, loops or breaks. Except when
particular materials are used, they shall conform to standard EN 2083 or EN 4434 or shall satisfy the
mechanical tests in EN 3475-505 to EN 3475-508 before use.
Where spiral screening is used, the first lay direction shall be contrary to that of the cabled cores.
4.3.3.2 Joints
Splices of the individual strands or strips may be affected by brazing, soldering or folding in.
There shall be no more than one (1) splice per 3 m cable length (measured between different individual
strands or strips).
4.3.3.3 Braid screen pushback capability
In accordance with Table 1, test 6.49.
4.3.3.4 Angle of spiral screening
...