SIST I-ETS 300 490-3 E1:2003

SLOVENSKI STANDARD
01-december-2003
7HUPLQDOVNDRSUHPD7(±3UHQRVGDWRWHNSUHNGLJLWDOQHJDRPUHåMD]LQWHJULUDQLPL
VWRULWYDPL,6'1±6SHFLILNDFLMDSUHVNXãDQMDVNODGQRVWL±GHO3URILOVNR
VSHFLILþQDVSHFLILNDFLMDSUHVNXãDQMD3676]DSURILO(852),/((76
Terminal Equipment (TE); File transfer over the Integrated Services Digital Network
(ISDN); Conformance testing specification; Part 3: Profile Specific Test Specification
(PSTS) for the EUROFILE profile (ETS 300 383)
Ta slovenski standard je istoveten z: I-ETS 300 490-3 Edition 1
ICS:
33.080 Digitalno omrežje z Integrated Services Digital
integriranimi storitvami Network (ISDN)
(ISDN)
35.180 Terminalska in druga IT Terminal and other
periferna oprema IT peripheral equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERIM
EUROPEAN I-ETS 300 490-3
TELECOMMUNICATION September 1996
STANDARD
Source: ETSI TC-TE Reference: DI/TE-01044-3
ICS: 33.080, 35.180
Key words: ISDN, EUROFILE, conformance testing, file transfer
Terminal Equipment (TE);
File transfer over the Integrated Digital Services Network (ISDN);
Conformance testing specification
Part 3: Profile Specific Test Specification (PSTS)
for the EUROFILE profile (ETS 300 383)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.fr
Tel.: +33 92 94 42 00 - Fax: +33 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1996. All rights reserved.

Page 2
I-ETS 300 490-3: September 1996
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.

Page 3
I-ETS 300 490-3: September 1996
Contents
Foreword .9
1 Scope .11
2 Normative references.11
3 Definitions and abbreviations .12
3.1 Definitions .12
3.2 Abbreviations .12
4 General.13
5 Abstract Test Method .13
6 Test requirements .15
6.1 General requirements .15
6.2 Low layer requirements.15
6.2.1 Layer 1 protocols.15
6.2.2 Layer 2 protocols, D-channel layer.15
6.2.3 Layer 3 protocols D-channel layer.15
6.2.3.1 Terminal selection and compatibility checking .15
6.2.3.2 Service specific use of supplementary services.15
6.2.4 Information transfer attributes .15
6.2.5 Access attributes.16
6.3 End-to-end protocol .16
6.4 IUT test suite specific requirements .16
6.4.1 Test file.16
6.4.2 Access control list.16
6.4.3 Correspondent phone book.17
7 Profile Specific Test Specification (PSTS) .17
7.1 Additional selected Test Cases of other conformance test specifications.17
7.2 Relevant Test Cases from I-ETS 300 491-3.17
7.3 Relevant Syntax-Based Videotex end-to-end protocol DTE-DTE Test Cases .21
7.4 Relevant ISDN lower layer protocol telematic service Test Cases.23
8 Profile specific conformance tests .24
8.1 Test Suite Structure (TSS) and Test Groups.24
8.1.1 Test Suite Structure (TSS) .24
8.1.2 Test groups .27
8.1.2.1 Main test groups .27
8.1.2.2 Test steps .28
8.1.3 Test Purpose naming conventions.29
8.2 Mapping of replacement Test Purposes from ETS 300 075.30
8.3 Additional and replacement Test Purposes description.30
8.3.1 IUT as a Master.30
8.3.1.1 E/M/Capability tests (CA).30
8.3.1.1.1 E/M/CA/Association .30
8.3.1.1.2 E/M/CA/Access.31
8.3.1.1.3 E/M/CA/Directory .31
8.3.1.1.4 E/M/CA/File Transfer .31
8.3.1.1.5 E/M/CA/Typed Data.31
8.3.1.1.6 E/M/CA/Navigation.31
8.3.1.2 E/M/Valid Behaviour Tests (BV) .32
8.3.1.2.1 E/M/BV/Protocol Interactions (PI) .32
8.3.1.2.1.1 E/M/BV/PI/Access.32

Page 4
I-ETS 300 490-3: September 1996
8.3.1.2.1.2 E/M/BV/PI/File Transfer . 33
8.3.1.2.1.3 E/M/BV/PI/Navigation. 34
8.3.1.2.2 E/M/BV/Parameter Variations (PV) . 34
8.3.1.2.2.1 E/M/BV/PV/Association. 34
8.3.1.2.2.2 E/M/BV/PV/Access. 35
8.3.1.2.2.3 E/M/BV/PV/Directory . 35
8.3.1.2.3 E/M/BV/Invalid Event (IE). 35
8.3.1.2.3.1 E/M/BV/IE/Directory . 36
8.3.1.2.3.2 E/M/BV/IE/File Transfer . 36
8.3.1.3 E/M/Invalid Behaviour Tests (BI). 37
8.3.1.3.1 E/M/BI/Parameter Variations (PV) . 37
8.3.1.3.1.1 E/M/BI/PV/Access . 37
8.3.1.3.1.2 E/M/BI/PV/Typed Data . 37
8.3.1.3.2 E/M/BI/Parameter Combinations (PC) . 38
8.3.1.3.2.1 E/M/BI/PC/Access. 38
8.3.1.4 E/M/Inopportune Behaviour Tests (BO). 38
8.3.1.4.1 E/M/BO/Inopportune Event (IE). 38
8.3.1.4.1.1 E/M/BO/IE/Access. 38
8.3.1.4.1.2 E/M/BO/IE/Directory. 38
8.3.1.4.1.3 E/M/BO/IE/File Transfer. 39
8.3.1.5 E/M/Services. 39
8.3.1.5.1 E/M/SE/Information supplied. 39
8.3.1.5.1.1 E/M/SE/IN/File Transfer . 39
8.3.1.5.1.2 E/M/SE/IN/Phases of communication . 40
8.3.1.5.1.3 E/M/SE/IN/File administration . 40
8.3.1.5.1.4 E/M/SE/IN/Message. 42
8.3.1.5.2 E/M/SE/Phonebook. 42
8.3.1.5.2.1 E/M/SE/PB/Phases of communication. 42
8.3.1.5.3 E/M/SE/Logbook . 42
8.3.1.5.3.1 E/M/SE/LB/File Transfer . 42
8.3.1.5.3.2 E/M/SE/LB/Phases of communication . 43
8.3.1.5.3.3 E/M/SE/LB/File administration. 43
8.3.1.5.3.4 E/M/SE/LB/Message . 43
8.3.2 IUT as a Slave . 44
8.3.2.1 E/S/Capability tests . 44
8.3.2.1.1 E/S/CA/Association . 44
8.3.2.1.2 E/S/CA/Access. 44
8.3.2.1.3 E/S/CA/Directory . 44
8.3.2.1.4 E/S/CA/File Transfer . 45
8.3.2.1.5 E/S/CA/Typed Data. 45
8.3.2.1.6 E/S/CA/Navigation. 45
8.3.2.2 E/S/Valid Behaviour Tests (BV) . 46
8.3.2.2.1 E/S/BV/Protocol Interactions (PI) . 46
8.3.2.2.1.1 E/S/BV/PI/Access. 46
8.3.2.2.1.2 E/S/BV/PI/File Transfer . 46
8.3.2.2.1.3 E/S/BV/PI/Navigation . 47
8.3.2.2.2 E/S/BV/Parameter Variations (PV). 47
8.3.2.2.2.1 E/S/BV/PV/AS . 48
8.3.2.2.2.2 E/S/BV/PV/Access . 49
8.3.2.2.2.3 E/S/BV/PV/Directory. 50
8.3.2.2.2.4 E/S/BV/PV/Save. 50
8.3.2.2.2.5 E/S/BV/PV/Load. 51
8.3.2.2.2.6 E/S/BV/PV/Rename . 51
8.3.2.2.3 E/S/BV/Parameter Combinations (PC) 51
8.3.2.2.3.1 E/S/BV/PC/Directory . 51
8.3.2.2.4 E/S/BV/Inopportune Event (IE). 52
8.3.2.2.4.1 E/S/BV/IE/File Transfer . 52
8.3.2.2.4.2 E/S/BV/IE/Navigation . 53
8.3.2.3 E/S/Invalid Behaviour Tests (BI) . 53
8.3.2.3.1 E/S/BI/Parameter Variations (PV) . 54
8.3.2.3.1.1 E/S/BI/PV/Association. 54
8.3.2.3.1.2 E/S/BI/PV/Access. 55
8.3.2.3.1.3 E/S/BI/PV/Directory . 55

Page 5
I-ETS 300 490-3: September 1996
8.3.2.3.1.4 E/S/BI/PV/Save.56
8.3.2.3.1.5 E/S/BI/PV/Load.56
8.3.2.3.1.6 E/S/BI/PV/Rename .57
8.3.2.3.1.7 E/S/BI/PV/Delete.58
8.3.2.3.1.8 E/S/BI/PV/Typed Data .59
8.3.2.3.1.9 E/S/BI/PV/Navigation .59
8.3.2.4 E/S/Inopportune Behaviour Tests (BO) .59
8.3.2.4.1 E/S/BO/Inopportune Event (IE).59
8.3.2.4.1.1 E/S/BO/IE/FT .59
8.3.2.5 E/S/Services .60
8.3.2.5.1 E/S/SE/Information supplied.60
8.3.2.5.1.1 E/S/SE/IN/File Transfer .60
8.3.2.5.1.2 E/S/SE/IN/Phases of communication .61
8.3.2.5.1.3 E/S/SE/IN/File administration.62
8.3.2.5.1.4 E/S/SE/IN/Message .62
8.3.2.5.2 E/S/SE/Logbook.62
8.3.2.5.2.1 E/S/SE/LB/File administration.62
8.3.2.5.2.2 E/S/SE/LB/Message .62
8.3.3 Local services.63
8.3.3.1 E/L/Configuration.63
8.3.3.2 E/L/Phonebook .63
8.3.3.3 E/L/File List.64
8.3.3.4 E/L/Logbook.65
8.3.3.5 E/L/Information Supplied .65
8.4 Combined Test Purposes .65
9 Profile Specific Test Specification convention.66
9.1 Naming conventions .66
9.1.1 Overview part .66
9.1.2 Declaration part .66
9.1.3 Constraint part.68
9.1.4 Dynamic part .69
9.1.4.1 Test Cases .69
9.1.4.2 Test steps .69
9.1.5 PTS abbreviations .69
9.2 Implementation conventions .69
9.2.1 General conventions .69
9.2.2 Declaration part .69
9.2.3 Constraint part.70
9.2.4 Dynamic part .70
Annex A (normative): Abstract Test Suite (ATS).71
A.1 The TTCN Graphical form (TTCN.GR) .71
A.2 The TTCN Machine Processable form (TTCN.MP) .71
Annex B (normative): Profile specific IXIT proforma for the EUROFILE protocol (ETS 300 383) .72
B.1 Identification summary .72
B.1.1 Profile IXIT .72
B.1.2 Profile Specific Test Suite Summary .72
B.1.3 Test Laboratory.73
B.1.4 Client.74
B.1.5 SUT.75
B.1.6 Ancillary Protocols .75
B.2 Profile Information for the EUROFILE protocol (ETS 300 383) .76
B.2.1 Profile Specific Information.76
B.2.2 IUT Information.76
B.2.2.1 Addresses .76
B.2.3.2 Parameter Values.76
B.2.3.3 Test files.77

Page 6
I-ETS 300 490-3: September 1996
B.2.3.3.1 General test files . 77
B.2.3.3.2 T-Directory testing test files . 77
B.2.3.3.3 Not allowed test file. 77
B.2.3.4 Navigation filestore . 78
B.2.3.5 Identifiers in the Access control list. 78
B.2.3.5.1 Allowed identifiers . 78
B.2.3.5.2 Not allowed identifiers. 79
B.2.3.6 Procedural information. 79
Annex C (normative): Profile Conformance Test Report proforma (Profile CTR) . 80
C.1 Identification summary. 80
C.1.1 Profile Conformance Test Report . 80
C.1.2 IUT. 80
C.1.3 Testing Environment . 80
C.1.4 Limits and reservations . 81
C.1.5 Comments. 81
C.2 IUT conformance status . 81
C.3 Static conformance summary. 81
C.4 Dynamic conformance summary. 81
C.5 Static conformance review report . 81
C.6 Test campaign report. 81
C.7 Observations. 86
Annex D (normative): System Conformance Test Report proforma (SCTR) . 87
D.1 Identification summary. 87
D.1.1 System Conformance Test Report. 87
D.1.2 Test Laboratory . 87
D.1.3 Client . 87
D.1.4 SUT . 87
D.1.5 Profile . 88
D.1.6 Nature of conformance testing. 88
D.1.7 Limits and reservations . 88
D.1.8 Record of agreement . 88
D.1.9 Comments. 88
D.2 System Report Summary. 89
D.2.1 Profile Testing Summary for ETS 300 080. 89
D.2.2 Protocol SBV layer testing. 90
D.2.3 Protocol Layer Testing Summary for ETS 300 075 restricted to ETS 300 383. 91
D.2.4 Profile Testing Summary for ETS 300 383. 92
Annex E (normative): System Conformance Statement proforma (SCS) . 93
E.1 Identification summary. 93
E.1.1 SCS Identification. 93
E.1.2 IUT Identification . 93
E.1.3 Client Identification. 93
E.1.4 Supplier Identification. 93
E.1.5 Manufacturer Identification (if different from client) . 94
E.1.6 Protocols Identification . 94
E.1.7 Profile Identification. 94
E.2 Miscellaneous System Information. 94
E.2.1 Configuration. 94
E.2.2 Other Information . 94

Page 7
I-ETS 300 490-3: September 1996
Annex F (informative): EUROFILE profile (ETS 300 383) Conformance Test Cases count .95
Annex G (informative): Bibliography.96
History.97

Page 8
I-ETS 300 490-3: September 1996
Blank page
Page 9
I-ETS 300 490-3: September 1996
Foreword
Part 3 of this Interim European Telecommunication Standard (I-ETS) has been produced by the Terminal
Equipment (TE) Technical Committee of the European Telecommunications Standards Institute (ETSI).
An ETSI standard may be given I-ETS status either because it is regarded as a provisional solution ahead
of a more advanced standard, or because it is immature and requires a "trial period". The life of an I-ETS
is limited to three years after which it can be converted into an ETS, have it's life extended for a further
two years, be replaced by a new version, or be withdrawn.
This is the third part of an I-ETS which comprises three parts as follows:
"Terminal Equipment (TE); File transfer over the Integrated Services Digital Network (ISDN);
Conformance testing specification:
Part 1: Profile Implementation Conformance Statement (ICS) proforma for the EUROFILE profile
ETS 300 383);
Part 2: Profile Test Specification Summary (PTS-Summary) for the EUROFILE profile
(ETS 300 383);
Part 3: Profile Specific Test Specification (PSTS) for the EUROFILE profile (ETS 300 383).
Proposed announcement date
Date of adoption of this I-ETS: 30 August 1996
Date of latest announcement of this I-ETS (doa): 31 December 1996

Page 10
I-ETS 300 490-3: September 1996
Blank page
Page 11
I-ETS 300 490-3: September 1996
1 Scope
Part 3 of this Interim European Telecommunication Standard (I-ETS) describes all the aspects of testing
for the EUROFILE profile (ETS 300 383 [1]). This is the third part of EUROFILE conformance testing, and
is the structuring document of the Profile Testing Standard, complementary to the Profile test Specification
Summary (PTS-Summary) as given in I-ETS 300 490-2 [2] and the profile Implementation Conformance
Statement (ICS) proforma for ETS 300 383 (I-ETS 300 490-1 [3]).
2 Normative references
Part 3 of this I-ETS incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this part of the I-ETS only when incorporated in it by amendment or revision. For undated
references the latest edition of the publication referred to applies.
[1] ETS 300 383 (1995): "Integrated Services Digital Network (ISDN); File transfer
over the ISDN EUROFILE transfer profile".
[2] I-ETS 300 490-2 (1995): "Terminal Equipment (TE); File transfer over the
Integrated Services Digital Network (ISDN); Conformance testing specification;
Part 2: Profile Test Specification Summary (PTS-Summary) for the EUROFILE
profile (ETS 300 383)".
[3] I-ETS 300 490-1 (1995): "Terminal Equipment (TE); File transfer over the
Integrated Services Digital Network (ISDN); Conformance testing specification;
Part 1: profile Implementation Conformance Statement (ICS) proforma for the
EUROFILE profile (ETS 300 383)".
[4] ETS 300 012 (1992): "Integrated Service Digital Network (ISDN); Basic rate
user-network interface, Layer 1 specification and test principles".
[5] ETS 300 011 (1992): "Integrated Service Digital Network (ISDN); Primary rate
user-network interface, Layer 1 specification and test principles".
[6] ETS 300 125 (1991): "Integrated Service Digital Network (ISDN); User-network
interface data layer link layer specifications Applications of CCITT
Recommendations Q.920/I.440 and Q.921/I.441".
[7] ETS 300 102-1 (1993): "Integrated Service Digital Network (ISDN);
User-network interface layer 3 specifications for basic call control".
[8] ETS 300 080 (1992): "Integrated Service Digital Network (ISDN); ISDN lower
layer protocols for telematic terminals".
[9] I-ETS 300 491-3 (1995): "Terminal Equipment (TE); Conformance testing for file
transfer over the Integrated services Digital Network (ISDN); Part 3:
Conformance testing for ETS 300 075 restricted by ETS 300 383 -Abstract Test
Suite (ATS)".
[10] ETS 300 079 (1991): "Integrated Services Digital Network (ISDN); Syntax-based
Videotex, End-to-end protocols circuit mode DTE-DTE".
[11] I-ETS 300 236 (1993): "Terminal Equipment (TE); Syntax-based Videotex
protocol, Terminal conformance testing".
[12] ETS 300 406 (1995): "Methods for Testing and Specification (MTS); Protocol
and profile conformance testing specifications; Standardization methodology".
[13] ETS 300 075 (1994): "Terminal Equipment (TE); Processable data, File
transfer".
Page 12
I-ETS 300 490-3: September 1996
[14] ITU-T Recommendation T.51 (1993): "Coded character sets for telematic
services".
[15] I-ETS 300 491-2 (1995): "Terminal Equipment (TE); Conformance testing for file
transfer over the Integrated services Digital Network (ISDN); Part 2: ETS 300
075 Test Suite Structure and Test Purposes (TSS&TP)".
[16] ISO/IEC 9646-5 (1994): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 5:
Requirements on test laboratories and clients for the Conformance Assessment
Process".
[17] ISO/IEC 9646-3 (1993): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 3:
Tree and Tabular Combined Notation (TTCN)".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of this part of the I-ETS, the definitions given in ISO/IEC 9646, Parts 1 to 8,
ETS 300 075 [13] and ETS 300 383 [1] apply.
3.2 Abbreviations
For the purposes of this part of the I-ETS, the following abbreviations apply:
ASP Abstract Service Primitive
ATM Abstract Test Method
ATS Abstract Test Suite
CTP Combined Test Purpose
DTE Data Terminal Equipment
HLC Higher Layer Compatibility
ICS Implementation Conformance Statement
ISDN Integrated Services Digital Network
IUT Implementation Under Test
IXIT Implementation eXtra Information for Testing
LT Lower Tester
OSI Open Systems Interconnect
PCO Point of Control and Observation
PCTR Protocol Conformance test Report
PDU Protocol Data Unit
PICS Protocol Implementation Conformance Statement
PIXIT Protocol Implementation eXtra Information for Testing
Profile CTR Profile Conformance Test Report
Profile ICS Profile Implementation Conformance Statement
PSTS Profile Specific Test Specification
PTS Profile Test Specification
PTS-Summary Profile Test Specification Summary
RL Requirement List
SBV Syntax-Based Videotex
SCS System Conformance Statement
SCTR System Conformance Test Report
SUT System Under Test
TE Terminal Equipment
TP Test Purposes
TSS Test Suite Structure
TTCN Tree and Tabular Combined Notation
UT Upper Tester
Page 13
I-ETS 300 490-3: September 1996
4 General
This part of the I-ETS describes all the aspects of testing.
The Abstract Test Suite (ATS) is specified in annex A.
NOTE: The ATS is written in Tree and Tabular Combined Notation (TTCN) and follows the
rules of ISO/IEC 9646-3 [17]. The ATS exists in machine processable form
(DIP04903.MP) and is the property of ETSI.
Additional Selected Test Cases of other Conformance test specifications are described in clause 7.
5 Abstract Test Method
This clause describes the Abstract Test Method (ATM), the Points of Control and Observation (PCO) used
to test the simple file transfer over the Integrated Services Digital Network (ISDN).
The Remote multi layer test method shall be used.

Page 14
I-ETS 300 490-3: September 1996
The following figure shows the ATM.
Testsystem SUT
UT
LT1
IUT
TDU T-Protocol
Layer
TDU
LT2
layer
SBV
SBV-Protocol
Layer
PCO1 Syntax
based
Videotex
End-to-end
protocols
PCO2
DTE-DTE
Syntax based Videotex
End-to-end protocols
DTE-DTE
Service Provider
Lower layer protocols Lower layer protocols
ISDN
for telematic term inals for telematic terminals
LT A Lower Tester (LT) is located in the test system. It controls and observes the
behaviours of the Implementation Under Test (IUT).
PCO1 The PCO one is defined between T-Service user and T-Service provider
(see ETS 300 075 [13], page 18, "Case of Syntax-Based Videotex:"). PCO1 is
the main PCO in the ATS.
PCO2 The PCO two is defined below the syntax-Based Videotex layer. It serves only
for specific Test Cases to observe the behaviour of used Syntax-Based
Videotex (see ETS 300 075 [13], subclause 6.5). PCO2 serves only for specific
Test Cases and does not serve to observe all Test Cases. The reason for
PCO2, is that if the IUT sends a T_Abort or a T_Release then the reaction on
PCO1 cannot be observed.
Service Provider The Service Provider consists partly of Syntax based Videotex End-to-End
protocols DTE-DTE (ETS 300 079 [10]) and Lower layer protocols for telematic
terminals (ETS 300 080 [8]).
IUT ETS 300 075 [13] restricted to EUROFILE profile is the IUT. It belongs to the
System Under Test (SUT).
UT No explicit Upper Tester (UT) exists in the test system. However, the SUT
needs to carry out some IUT actions by the user interface to achieve some
effects of test co-ordination procedures. The controls of the IUT are implied or
informally expressed in the ATS, but no assumption shall be made regarding
their feasibility or realisation.
NOTE: This ATM cannot be used for the testing of local services. In order to test local services this test
specification describes the test in the ATS with text, and the tester shall realize those local
service tests by the specific procedure described in annex B.
Figure 1: ATM
Page 15
I-ETS 300 490-3: September 1996
6 Test requirements
6.1 General requirements
For this conformance test specification all the requirements to carry out the tests are given.
To realize this conformance test specification it is necessary that all the layers below work properly. For
this reason, lower layers shall be checked before this specification by relevant conformance test
specifications, see clause 7.
This test specification does not deal with the details of the human interface. Only Protocol Data Units
(PDUs) and Parameters are observed and controlled at the PCOs.
The tester shall observe the order of transmission of parameters within a PDU. At present, a fixed order of
transmission of parameters is not required by the I-ETS. Consequently, the test equipment shall realize
the receiving of parameters in different order.
6.2 Low layer requirements
Clause 10 of ETS 300 383 [1] shall apply without any additional application rules.
Additional requirements or references to referenced documents are given in the following subclauses.
6.2.1 Layer 1 protocols
For terminals using basic access to an ISDN, ETS 300 012 [4] shall apply without any additional
application rules.
For terminals using the primary rate access to an ISDN, ETS 300 011 [5] shall apply without any additional
application rules.
6.2.2 Layer 2 protocols, D-channel layer
ETS 300 125 [6] shall apply without any additional rules.
6.2.3 Layer 3 protocols D-channel layer
Additional requirements and amendments are given in the following subclauses.
6.2.3.1 Terminal selection and compatibility checking
Subclause 10.2.2 of ETS 300 383 [1] describes the use of the "Eurofile" Higher Layer Compatibility (HLC)
codepoint . This codepoint is not available and is thus not relevant for testing.
6.2.3.2 Service specific use of supplementary services
No supplementary service tests are contained in this I-ETS.
6.2.4 Information transfer attributes
The information transfer attributes of this teleservice are specified in table 1.

Page 16
I-ETS 300 490-3: September 1996
Table 1: Values of information transfer attributes
Attribute Possible values
Information transfer mode Circuit
Information transfer rate 64 kbit/s
Information transfer capability Unrestricted digital information
Structure 8 kHz integrity
Establishment of communication On demand
Symmetry Bi-directional symmetric
Communication configuration Point-to-point
6.2.5 Access attributes
The access attributes of this teleservice are specified in table 2.
Table 2: Values
Attribute Possible values
Access channel and rate User information
- B-channel
Signalling
- D-channel
Signalling access protocol ETS 300 125 [6] and 300 102-1 [7]
Information access protocol ETS 300 080 [8]
6.3 End-to-end protocol
Clause 9 in ETS 300 383 [1] shall apply without any additional rules.
6.4 IUT test suite specific requirements
Before the test specification is started the tester shall configure the IUT (SUT). The test files, the access
control list and the Correspondent phonebook shall be prepared.
6.4.1 Test file
This ATS gives a fixed order of directories and files. The tester shall activate transactions for certain Test
Cases at the IUT user interface. For this reason, the tester shall realize the following designations of files
in the IUT in the directory 'eurotest' as follows:
- File type group A (default):
a) tstde_2, tstlo_1, tstre_n1, tstre_o1, tstre_o2, tstre_3, tstsa_2.
The content of the files is defined in Annex A, in the TTCN description.
6.4.2 Access control list
For the carrying out of tests, the tester shall prepare the access control list as follows:
Services: Restrictions to services shall not be allowed.
Identifier: Name: TESTEURO and Password: testrun shall be granted, i.e. the following
identifier: "TESTEURO/testrun".
Working area: EUROTEST.
NOTE: Additional rules for identifiers are given in annex B, subclause B.2.3.5.

Page 17
I-ETS 300 490-3: September 1996
6.4.3 Correspondent phone book
For carrying out the tests, the tester shall prepare the Corresponding phone book as follows:
Services: Restrictions to services shall not be allowed.
Called address: TSPX_CALLED_ADDRESS, see annex B, subclause B.2.3.2.
Local working filestore: EUROTEST.
7 Profile Specific Test Specification (PSTS)
7.1 Additional selected Test Cases of other conformance test specifications
Before carrying out the tests the correct implementation of the lower layers shall be checked and other
Protocol Conformance Test Report (PCTR) should be used.
This clause gives an overview about additional test specifications. Relevant test specifications are showed
in the figure below.
EURO FILE profile
prI-ETS 300 491-3 [9]
and
this PSTS
SUT
Syntax based Videotex protocol
Terminal c onformance testing
ISD N
I-ETS 300 236 [11]
Figure 2: Test specifications
7.2 Relevant Test Cases from I-ETS 300 491-3
See the list of Test Cases used in I-ETS 300 491-3 [9].
This I-ETS describes all references used for testing the EUROFILE profile (ETS 300 383 [1]).

Page 18
I-ETS 300 490-3: September 1996
Table 3: List of Test Purposes applicable to the profile
Test Purpose group Test Case Identification Remarks
S/CA/AS TCS2_102
S/CA/AC TCS2_202
S/CA/SA TCS2_401
S/CA/LO TCS2_501
S/CA/RE TCS2_601
S/CA/DE TCS2_701
S/CA/FT TCS2_802
S/BV/PI/AS TCS3I101
S/BV/PI/FT TCS3I802
S/BV/PI/FT TCS3I804
S/BV/PI/FT TCS3I805
S/BV/PI/FT TCS3I807
S/BV/PI/FT TCS3I808
S/BV/PI/FT TCS3I809
S/BV/PI/FT TCS3I810
S/BV/PI/TD TCS3I901
S/BV/PV/AC TCS3V201
S/BV/PV/AC TCS3V202
S/BV/PV/AC TCS3V203
S/BV/PV/DI TCS3V301
S/BV/PV/SA TCS3V401
S/BV/PV/LO TCS3V501
S/BV/PV/RE TCS3V601
S/BV/PV/RE TCS3V602
S/BV/PV/DE TCS3V701
S/BV/PV/FT TCS3V801
S/BV/PV/FT TCS3V802
S/BV/PV/FT TCS3V804
S/BV/PC/DI TCS3C301
S/BV/PC/SA TCS3C401
S/BV/PC/LO TCS3C501
S/BV/PC/RE TCS3C601
S/BV/PC/DE TCS3C701
S/BV/PC/FT TCS3C602
S/BV/IE/AS TCS3E101
S/BV/IE/AC TCS3E201
S/BV/IE/SA TCS3E401
S/BV/IE/LO TCS3E501
S/BI/PV/AS TCS5V101
S/BI/PV/AS TCS5V102
S/BI/PV/AS TCS5V103
S/BI/PV/AS TCS5V104
S/BI/PV/AS TCS5V105
S/BI/PV/AC TCS5V201
S/BI/PV/AC TCS5V202
S/BI/PV/AC TCS5V203
S/BI/PV/DI TCS5V301
S/BI/PV/SA TCS5V401
(continued)
Page 19
I-ETS 300 490-3: September 1996
Table 3 (continued): List of Test Purposes applicable to the profile
Test Purpose group Test Case Identification Remarks
S/BI/PV/LO TCS5V501
S/BI/PV/DE TCS5V701
S/BI/PV/FT TCS5V801
S/BI/PV/FT TCS5V803
S/BI/PV/FT TCS5V804
S/BI/PV/FT TCS5V807
S/BI/PV/FT TCS5V808
S/BI/PV/FT TCS5V809
S/BI/PV/FT TCS5V810
S/BI/PV/FT TCS5V811
S/BI/PV/TD TCS5V901
S/BI/PC/FT TCS5C801
S/BI/PC/FT TCS5C802
S/BO/IE/AS TCS4E101
S/BO/IE/AS TCS4E102
S/BO/IE/AS TCS4E103
S/BO/IE/AC TCS4E201
S/BO/IE/AC TCS4E202
S/BO/IE/AC TCS4E203
S/BO/IE/SA TCS4E401
S/BO/IE/SA TCS4E402
S/BO/IE/LO TCS4E501
S/BO/IE/FT TCS4E801
S/BO/IE/FT TCS4E802
M/CA/AS TCM2_102
M/CA/AC TCM2_202
M/CA/SA TCM2_401
M/CA/LO TCM2_501
M/CA/RE TCM2_601
M/CA/DE TCM_701
M/BV/PI/AS TCM3I101
M/BV/PI/AS TCM3I102
M/BV/PI/AC TCM3I201
M/BV/PI/DI TCM3I301
M/BV/PI/SA TCM3I401
M/BV/PI/SA TCM3I402
M/BV/PI/LO TCM3I501
M/BV/PI/LO TCM3I502
M/BV/PI/RE TCM3I601
M/BV/PI/DE TCM3I701
M/BV/PI/FT TCM3I802
M/BV/PI/FT TCM3I804
M/BV/PI/FT TCM3I805
M/BV/PI/FT TCM3I807
M/BV/PI/FT TCM3I808
M/BV/PI/FT TCM3I809
M/BV/PI/FT TCM3I810
(continued)
Page 20
I-ETS 300 490-3: September 1996
Table 3 (continued): List of Test Purposes applicable to the profile
Test Purpose group Test Case Identification Remarks
M/BV/PI/FT TCM3I8011
M/BV/PI/TD TCM3I901
M/BV/PV/FT TCM3V801
M/BV/PV/FT TCM3V802
M/BV/IE/AS TCM3E101
M/BV/IE/AS TCM3E102
M/BV/IE/AC TCM3E201
M/BV/IE/AC TCM3E202
M/BV/IE/SA TCM3E401
M/BV/IE/SA TCM3E402
M/BV/IE/LO TCM3E501
M/BV/IE/LO TCM3E502
M/BV/IE/TD TCM3E901
M/BV/IE/TD TCM3E902
M/BV/TI/AC TCM3T201
M/BV/TI/DI TCM3T301
M/BV/TI/FT TCM3T801
M/BI/PV/AS TCM5V101
M/BI/PV/AS TCM5V102
M/BI/PV/AS TCM5V103
M/BI/PV/AS TCM5V104
M/BI/PV/AC TCM5V201
M/BI/PV/AC TCM5V202
M/BI/PV/AC TCM5V204
M/BI/PV/DI TCM5V301
M/BI/PV/SA TCM5V401
M/BI/PV/LO TCM5V501
M/BI/PV/RE TCM5V601
M/BI/PV/DE TCM5V701
M/BI/PV/FT TCM5V801
M/BI/PV/FT TCM5V802
M/BI/PV/FT TCM5V803
M/BI/PV/FT TCM5V806
M/BI/PV/FT TCM5V807
M/BI/PV/FT TCM5V808
M/BI/PV/TD TCM5V901
M/BI/PC/FT TCM5C801
M/BI/PC/FT TCM5C802
M/BO/IE/AS TCM4E101
M/BO/IE/AS TCM4E102
M/BO/IE/AS TCM4E103
M/BO/IE/AS TCM4E104
M/BO/IE/AS TCM4E105
M/BO/IE/AC TCM4E201
M/BO/IE/AC TCM4E202
M/BO/IE/AC TCM4E203
M/BO/IE/AC TCM4E204
M/BO/IE/AC TCM4E205
M/BO/IE/AC TCM4E206
(continued)
Page 21
I-ETS 300 490-3: September 1996
Table 3 (concluded): List of Test Purposes applicable to the profile
Test Purpose group Test Case Identification Remarks
M/BO/IE/DI TCM4E301
M/BO/IE/SA TCM4E401
M/BO/IE/SA TCM4E402
M/BO/IE/LO TCM4E501
M/BO/IE/LO TCM4E502
M/BO/IE/LO TCM4E503
M/BO/IE/RE TCM4E601
M/BO/IE/DE TCM4E701
M/BO/IE/FT TCM4E801
M/BO/IE/FT TCM4E802
7.3 Relevant Syntax-Based Videotex end-to-end protocol DTE-DTE Test Cases
This test specification is based on Syntax-Based Videotex (SBV) end-to-end protocol DTE-DTE.
EUROFILE shall use the transparent mode (with no transport layer) and shall comply with
ETS 300 079 [10].
The ETS 300 079 [10] TDUs to implement the transparent mode are:
- SBV_TPD_Begin;
- SBV_TPD_End;
- SBV_TC_Error.
For further details see ETS 300 383 [1], clause 9.
Additional Test Cases that shall be tested are included in I-ETS 300 236 [11], see table 4 below. The
referenced tables in the Test Case Name column are referencing out to I-ETS 300 23
...