SIST EN IEC 62343-2-1:2020

SLOVENSKI STANDARD
SIST EN IEC 62343-2-1:2020
01-februar-2020
Nadomešča:
SIST EN 62343-2:2014
Dinamični moduli - 2-1. del: Kvalifikacije zanesljivosti - Predloga za preverjanje
(IEC 62343-2-1:2019)
Dynamic modules - Part 2-1: Reliability qualification - Test template (IEC 62343-2-
1:2019)
Dynamische Module - Teil 2-1: Zuverlässigkeitsnachweis - Prüfvorlage (IEC 62343-2-
1:2019)
Modules dynamiques - Partie 2-1: Qualification de fiabilité - Modèle d'essai (IEC 62343-2
-1:2019)
Ta slovenski standard je istoveten z: EN IEC 62343-2-1:2019
ICS:
33.180.01 Sistemi z optičnimi vlakni na Fibre optic systems in
splošno general
SIST EN IEC 62343-2-1:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62343-2-1:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 62343-2-1:2020
EUROPEAN STANDARD EN IEC 62343-2-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2019
ICS 33.180.01 Supersedes EN 62343-2:2014 and all of its amendments
and corrigenda (if any).
English Version
Dynamic modules - Part 2-1: Reliability qualification - Test
template
(IEC 62343-2-1:2019)
Modules dynamiques - Partie 2-1: Qualification de fiabilité - Dynamische Module - Teil 2-1: Zuverlässigkeitsnachweis -
Modèle d'essai Prüfvorlage
(IEC 62343-2-1:2019) (IEC 62343-2-1:2019)
This European Standard was approved by CENELEC on 2019-10-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62343-2-1:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62343-2-1:2020
EN IEC 62343-2-1:2019 (E)
European foreword
The text of document 86C/1567/CDV, future edition 1 of IEC 62343-2-1, prepared by SC 86C "Fibre
optic systems and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 62343-2-1:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-07-21
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-10-21
document have to be withdrawn
This document supersedes EN 62343-2:2014 and all of its amendments and corrigenda (if any). This
edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to EN 62343-2:2014:
a) addition of an Introduction to the background of this document;
b) replacement of "Reliability qualification consideration" by "reliability qualification test
consideration";
c) deletion of the consideration of "Design 1" and "Design 2" and change of the contents of
"Approach" in "Reliability qualification test considerations";
d) deletion of the details in "Reliability qualification requirements" and replacement by "Reliability
qualification test items";
e) deletion of "Reliability calculations" from the sum of failure rates of constituting parts;
f) integration of "Pass/fail criteria" and "Guidance of FMEA" into Annex B (informative);
g) simplification of test items and conditions in Annex A and change of title of Annex A to
"Examples of reliability qualification test conditions".
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 62343-2-1:2019 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60068-2-14 NOTE Harmonized as EN 60068-2-14
IEC 61300 (series) NOTE Harmonized as EN 61300 (series)
IEC 61300-2-4 NOTE Harmonized as EN IEC 61300-2-4
IEC 62005-9-1 NOTE Harmonized as EN 62005-9-1
IEC 62572-3 NOTE Harmonized as EN 62572-3

2

---------------------- Page: 4 ----------------------
SIST EN IEC 62343-2-1:2020
EN IEC 62343-2-1:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 62343 -  Dynamic modules – General and guidance EN 62343 -

3

---------------------- Page: 5 ----------------------
SIST EN IEC 62343-2-1:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 62343-2-1:2020



IEC 62343-2-1

®


Edition 1.0 2019-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Dynamic modules –

Part 2-1: Reliability qualification – Test template




Modules dynamiques –

Partie 2-1: Qualification de fiabilité – Modèle d'essai
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.180.01 ISBN 978-2-8322-7356-2




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 62343-2-1:2020
– 2 – IEC 62343-2-1:2019  IEC 2019
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 6
3.1 Terms and definitions . 6
3.2 Abbreviated terms . 7
4 Reliability qualification test considerations . 7
4.1 General . 7
4.2 Approach . 7
5 Reliability qualification test items . 8
Annex A (informative) Examples of reliability qualification test conditions . 9
Annex B (informative) Reliability qualification test recommendations . 10
B.1 General . 10
B.2 Pass/fail criteria . 10
B.3 Guidance of failure mode effect analysis (FMEA) and qualification of
similarity . 11
Bibliography . 12

Table 1 – Reliability qualification test items . 8
Table A.1 – Example of reliability qualification test conditions . 9

---------------------- Page: 8 ----------------------
SIST EN IEC 62343-2-1:2020
IEC 62343-2-1:2019  IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

DYNAMIC MODULES –

Part 2-1: Reliability qualification – Test template

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62343-2-1 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
This first edition cancels and replaces the second edition of IEC 62343-2 published in 2014.
This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to
IEC 62343-2:2014:
a) addition of an Introduction to the background of this document;
b) replacement of "Reliability qualification consideration" by "reliability qualification test
consideration";
c) deletion of the consideration of "Design 1" and "Design 2" and change of the contents of
"Approach" in "Reliability qualification test considerations";
d) deletion of the details in "Reliability qualification requirements" and replacement by
"Reliability qualification test items";

---------------------- Page: 9 ----------------------
SIST EN IEC 62343-2-1:2020
– 4 – IEC 62343-2-1:2019  IEC 2019
e) deletion of "Reliability calculations" from the sum of failure rates of constituting parts;
f) Integration of "Pass/fail criteria" and "Guidance of FMEA" into Annex B (informative);
g) Simplification of test items and conditions in Annex A and change of title of Annex A to
"Examples of reliability qualification test conditions".
The text of this International Standard is based on the following documents:
CDV Report on voting
86C/1567/CDV 86C/1594/RVC

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 62343 series, published under the general title Dynamic modules,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

NOTICE
This document contains material that is Copyright © 2006, Telcordia Technologies, Inc.
("Telcordia"). All rights reserved.
The reader is advised that this IEC document and Telcordia source(s) may differ, and the
context and use of said material in this IEC document may differ from that of Telcordia.
TELCORDIA MAKES NO REPRESENTATION OR WARRANTY, EXPRESS OR IMPLIED,
WITH RESPECT TO THE SUFFICIENCY, ACCURACY, OR UTILITY OF ANY INFORMATION
OR OPINION CONTAINED HEREIN. ANY USE OF OR RELIANCE UPON SAID
INFORMATION OR OPINION IS AT THE RISK OF THE USER. TELCORDIA SHALL NOT BE
LIABLE FOR ANY DAMAGE OR INJURY INCURRED BY ANY PERSON ARISING OUT OF
THE SUFFICIENCY, ACCURACY, OR UTILITY OF ANY INFORMATION OR OPINION
CONTAINED HEREIN.

---------------------- Page: 10 ----------------------
SIST EN IEC 62343-2-1:2020
IEC 62343-2-1:2019  IEC 2019 – 5 –
INTRODUCTION
Dynamic modules (DMs) are relatively new fibre optic devices. In the industry, there is no de-
facto standard of reliability qualification test requirements for DMs. Also, there are many types
and functions of DMs, such as optical path switching, wavelength management, chromatic
dispersion management, optical channel power management, and optical channel powers and
wavelength monitoring. Therefore, it is difficult to standardize the reliability qualif
...