Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum capillary

This document specifies a method for the determination of the dynamic viscosity of bituminous binders by means of a vacuum capillary viscometer at 60 °C in a range between 0,003 6 Pa⋅s and 580 000 Pa⋅s. Other temperatures are possible if calibration constants are known. Bituminous emulsions and non-newtonian binders (e.g. some polymer modified bitumen) are not within the scope of this method.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - Bestimmung der dynamischen Viskosität mit Vakuum-Kapillaren

Dieses Dokument legt ein Verfahren zur Bestimmung der dynamischen Viskosität von bitumenhaltigen Bindemitteln mit Hilfe eines Vakuum-Kapillar-Viskosimeters bei 60 °C im Bereich von 0,003 6 Pa · s bis 580 000 Pa · s fest. Andere Temperaturen sind möglich, wenn die Kalibrierkonstanten bekannt sind. Dieses Verfahren gilt nicht für Bitumenemulsionen und für nichtnewtonsche Bindemittel (z. B. einige polymermodifizierte Bitumen).
WARNUNG - Die Anwendung dieses Dokuments kann den Umgang mit gefährlichen Substanzen und Ausrüstungsteilen und die Ausführung gefährlicher Arbeitsgänge einschließen. Dieses Dokument erhebt nicht den Anspruch, alle mit seiner Anwendung verbundenen Sicherheitsprobleme anzusprechen. Es liegt in der Verantwortung des Anwenders dieses Dokuments, die Gefahren zu identifizieren und die mit der Durchführung der Prüfung verbundenen Risiken zu beurteilen sowie geeignete Kontrollmaßnahmen zu implementieren, um den Ausführenden (und die Umwelt) zu schützen. Dies beinhaltet einen angemessenen Arbeits- und Gesundheitsschutz sowie die Klärung vor der Anwendung, ob einschränkende Vorschriften zu berücksichtigen sind.

Bitumes et liants bitumineux - Détermination de la viscosité dynamique par viscosimètre capillaire sous vide

Le présent document prescrit une méthode pour la détermination de la viscosité dynamique de liants bitumineux au moyen d’un viscosimètre capillaire sous vide à 60 °C dans un intervalle de 0,003 6 Pa·s à plus de 580 000 Pa·s. D’autres températures sont possibles si les constantes d’étalonnage sont connues. Le domaine d'application de la présente méthode ne comprend pas les liants non-newtonien (par exemple certains bitumes modifiés par des polymères) ni les émulsions de bitumineuses.
NOTE 1   La présente méthode est considérée comme ne s’appliquant pas aux émulsions contenant des liants bitumineux. Elle peut être utilisée pour les liants récupérés et/ou stabilisés obtenus à partir d’émulsions.
NOTE 2   Le comportement visqueux particulier de certains bitumes modifiés par des polymères (BMP) n’est pas mis en évidence dans un viscosimètre capillaire sous vide. D’autres méthodes sont plus appropriées.
AVERTISSEMENT - L'utilisation de ce document implique l'intervention de produits, d'opérations et d'équipements à caractère dangereux. Le présent document n'est pas censé aborder tous les problèmes de sécurité concernés par son usage. Il incombe à son utilisateur d'identifier les dangers et d'évaluer les risques liés à l'application de cette méthode d'essai et de mettre en œuvre des mesures de prévention pour protéger les opérateurs (et l'environnement). Cela passe entre autre par l’’établissement de règles d'hygiène et de sécurité appropriées et la détermination de l'applicabilité des restrictions réglementaires avant utilisation.

Bitumen in bitumenska veziva - Določanje dinamične viskoznosti z metodo kapilare z vakuumom

Ta dokument določa metodo za določanje dinamične viskoznosti bitumenskih veziv z vakuumskim kapilarnim viskozimetrom pri 60 °C v razponu od 0,0036 Pa⋅s in 580.000 Pa⋅s. Druge temperature so možne, če so poznane kalibracijske konstante. Bitumenske emulzije in nenewtonska veziva (npr. e.g.nekateri polimerno modificirani bitumni) niso zajeti v tej metodi.
OPOZORILO: Pri uporabi tega dokumenta so lahko prisotni nevarni materiali, postopki in oprema. Ta dokument ne obravnava vseh varnostnih težav, ki se navezujejo na njegovo uporabo. Uporabnik tega dokumenta je odgovoren za prepoznavanje nevarnosti in oceno tveganj, povezanih z izvajanjem te preskusne metode, ter za izvajanje zadostnih nadzornih ukrepov za zaščito posameznih operaterjev (in okolja). To vključuje ustrezne varnostne in zdravstvene prakse ter določitev uporabnosti regulativnih omejitev pred uporabo.

General Information

Status
Published
Public Enquiry End Date
27-Feb-2022
Publication Date
17-Oct-2023
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Aug-2023
Due Date
06-Oct-2023
Completion Date
18-Oct-2023

Relations

Buy Standard

Standard
EN 12596:2023
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 12596:2022
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 12596:2023
01-november-2023
Nadomešča:
SIST EN 12596:2014
Bitumen in bitumenska veziva - Določanje dinamične viskoznosti z metodo
kapilare z vakuumom
Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum
capillary
Bitumen und bitumenhaltige Bindemittel - Bestimmung der dynamischen Viskosität mit
Vakuum-Kapillaren
Bitumes et liants bitumineux - Détermination de la viscosité dynamique par viscosimètre
capillaire sous vide
Ta slovenski standard je istoveten z: EN 12596:2023
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
SIST EN 12596:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 12596:2023

---------------------- Page: 2 ----------------------
SIST EN 12596:2023


EN 12596
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2023
EUROPÄISCHE NORM
ICS 75.140; 91.100.50 Supersedes EN 12596:2014
English Version

Bitumen and bituminous binders - Determination of
dynamic viscosity by vacuum capillary
Bitumes et liants bitumineux - Détermination de la Bitumen und bitumenhaltige Bindemittel -
viscosité dynamique par viscosimètre capillaire sous Bestimmung der dynamischen Viskosität mit Vakuum-
vide Kapillaren
This European Standard was approved by CEN on 28 May 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12596:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 12596:2023
EN 12596:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Apparatus . 6
6 Preparation of test samples . 8
7 Procedure . 8
8 Calculation . 9
9 Expression of results . 10
10 Precision . 10
10.1 Repeatability . 10
10.2 Reproducibility .
...

SLOVENSKI STANDARD
oSIST prEN 12596:2022
01-februar-2022
Bitumen in bitumenska veziva - Določanje dinamične viskoznosti z metodo
kapilare z vakuumom
Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum
capillary
Bitumen und bitumenhaltige Bindemittel - Bestimmung der dynamischen Viskosität mit
Vakuum-Kapillaren
Bitumes et liants bitumineux - Détermination de la viscosité dynamique par viscosimètre
capillaire sous vide
Ta slovenski standard je istoveten z: prEN 12596
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN 12596:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12596:2022

---------------------- Page: 2 ----------------------
oSIST prEN 12596:2022


DRAFT
EUROPEAN STANDARD
prEN 12596
NORME EUROPÉENNE

EUROPÄISCHE NORM

December 2021
ICS 75.140; 91.100.50 Will supersede EN 12596:2014
English Version

Bitumen and bituminous binders - Determination of
dynamic viscosity by vacuum capillary
Bitumes et liants bitumineux - Détermination de la Bitumen und bitumenhaltige Bindemittel -
viscosité dynamique par viscosimètre capillaire sous Bestimmung der dynamischen Viskosität mit Vakuum-
vide Kapillaren
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 336.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12596:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12596:2022
prEN 12596:2021 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 5
5 Apparatus . 5
6 Preparation of test samples . 7
7 Procedure . 7
8 Calculation . 8
9 Expression of results .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.