SIST EN 61169-58:2017

SLOVENSKI STANDARD
SIST EN 61169-58:2017
01-januar-2017
5DGLRIUHNYHQþQLNRQHNWRUMLGHO3RGURþQDVSHFLILNDFLMD]D5)NRDNVLDOQH
NRQHNWRUMH]EOLQGPDWHVNORSNR.DUDNWHULVWLþQDLPSHGDQFDRKPWLS6%0$
,(&
Radio-frequency connectors - Part 58: Sectional specification for RF coaxial connectors
with blind-mate coupling - characteristic impedance 50 ? (type SBMA) (IEC 61169-
58:2016)
Ta slovenski standard je istoveten z: EN 61169-58:2016
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML RF connectors
5)
SIST EN 61169-58:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61169-58:2017

---------------------- Page: 2 ----------------------

SIST EN 61169-58:2017


EUROPEAN STANDARD EN 61169-58

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2016
ICS 33.120.30

English Version
Radio-frequency connectors - Part 58: Sectional specification for
RF coaxial connectors with blind-mate coupling - Characteristic
impedance 50 O (type SBMA)
(IEC 61169-58:2016)
Connecteurs pour fréquences radioélectriques - Partie 58: Hochfrequenz-Steckverbinder - Teil 58:
Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für koaxiale HF-Steckverbinder mit
coaxiaux pour fréquences radioélectriques à accouplement Blindsteckverbindung - Wellenwiderstand 50 O (Typ SBMA)
en aveugle - Impédance caractéristique 50 O (type SBMA) (IEC 61169-58:2016)
(IEC 61169-58:2016)
This European Standard was approved by CENELEC on 2016-09-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61169-58:2016 E

---------------------- Page: 3 ----------------------

SIST EN 61169-58:2017
EN 61169-58:2016
European foreword
The text of document 46F/347/FDIS, future edition 1 of IEC 61169-58, prepared by SC 46F "RF and
microwave passive components", of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 61169-58:2016.
The following dates are fixed:
(dop) 2017-06-20
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2019-09-20
• latest date by which the national standards conflicting with
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61169-58:2016 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------

SIST EN 61169-58:2017
EN 61169-58:2016

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio-frequency connectors -- Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 62037-3 -  Passive RF and microwave devices, EN 62037-3 -
intermodulation level measurement -- Part
3: Measurement of passive intermodulation
in coaxial connectors

3

---------------------- Page: 5 ----------------------

SIST EN 61169-58:2017

---------------------- Page: 6 ----------------------

SIST EN 61169-58:2017




IEC 61169-58

®


Edition 1.0 2016-08




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Radio-frequency connectors –

Part 58: Sectional specification for RF coaxial connectors with blind-mate

coupling – Characteristic impedance 50 Ω (type SBMA)




Connecteurs pour fréquences radioélectriques –

Partie 58: Spécification intermédiaire relative aux connecteurs coaxiaux


pour fréquences radioélectriques à accouplement en aveugle – Impédance

caractéristique 50 Ω (type SBMA)












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.30 ISBN 978-2-8322-3600-0



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61169-58:2017
– 2 – IEC 61169-58:2016  IEC 2016
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references. 6
3 Mating face and gauge information . 7
3.1 Dimensions – General connectors . 7
3.1.1 Connector with socket centre contact . 7
3.1.2 Connector with socket-centre contact . 8
3.2 Gauges for general purpose connectors . 9
3.2.1 Gauge pins for socket centre contact . 9
3.2.2 Test procedure . 10
3.2.3 Gauge pins for outer contact . 10
3.2.4 Test procedure . 11
3.3 Dimensions – standard test connectors – grade 0 . 11
3.3.1 Connector with pin-centre contact. 11
3.3.2 Connector with socket-centre contact . 12
3.4 Requirements for installation . 12
3.4.1 Radial misalignment . 12
3.4.2 Axial separation between mating reference planes . 13
4 Quality assessment procedures . 14
4.1 General . 14
4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) . 14
4.3 Test schedule and inspection requirements. 16
4.3.1 Acceptance tests . 16
4.3.2 Periodic tests . 16
4.4 Procedures for the quality conformance . 19
4.4.1 Quality conformance inspection . 19
4.4.2 Qualification approval and its maintenance . 19
5 Instructions for preparation of detail specifications . 19
5.1 General . 19
5.2 Identification of the component . 19
5.3 Performances . 19
5.4 Marking, ordering information and related matters . 20
5.5 Selection of tests, test conditions and severities . 20
5.6 Blank detail specification pro-forma for type SMBA connector . 20
6 Marking . 24
6.1 Marking of component . 24
6.2 Marking and contents of package . 25

Figure 1 – Connector with pin centre contact (for dimensions, see Table 1) . 7
Figure 2 – Connector with socket centre contact (for dimensions, see Table 2) . 8
Figure 3 – Gauge pin for socket-centre contact (for dimensions, see Table 3) . 9
Figure 4 – Gauge pin for outer contact (for dimensions, see Table 4) . 10
Figure 5 – Connector with pin centre contact (for dimensions, see Table 5) . 11
Figure 6 – Connector with socket centre contact (for dimensions, see Table 6) . 12
Figure 7 – Radial misalignment . 13

---------------------- Page: 8 ----------------------

SIST EN 61169-58:2017
IEC 61169-58:2016  IEC 2016 – 3 –
Figure 8 – Rigidly mounted receptacle and jack . 13
Figure 9 – Rigidly mounted receptacle and float mounted jack . 14

Table 1 – Dimensions of connector with pin-centre contact . 8
Table 2 – Dimensions of connector with socket-centre contact . 9
Table 3 – Gauge pins dimensions for socket-centre contact . 9
Table 4 – Gauge pins dimensions for outer contact . 10
Table 5 – Dimensions of connector with pin-centre contact . 11
Table 6 – Dimensions of connector with socket-centre contact . 12
Table 7 – Rating and characteristics . 15
Table 8 – Acceptance tests . 17
Table 9 – Periodic tests . 18

---------------------- Page: 9 ----------------------

SIST EN 61169-58:2017
– 4 – IEC 61169-58:2016  IEC 2016
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 58: Sectional specification for RF
coaxial connectors with blind-mate coupling –
Characteristic impedance 50 Ω (type SBMA)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-58 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
RF connectors, RF and microwave passive components and accessories.
The text of this standard is based on the following documents:
FDIS Report on voting
46F/347/FDIS 46F/352/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 10 ----------------------

SIST EN 61169-58:2017
IEC 61169-58:2016  IEC 2016 – 5 –
A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,
can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.

---------------------- Page: 11 ----------------------

SIST EN 61169-58:2017
– 6 – IEC 61169-58:2016  IEC 2016
RADIO-FREQUENCY CONNECTORS –

Part 58: Sectional specification for RF
coaxial connectors with blind-mate coupling –
Characteristic impedance 50 Ω (type SBMA)



1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for SBMA series coaxial connectors with blind-
mate coupling.
The connectors are used with cables with characteristic impedance 50 Ω in an operating
frequency range up to 28 GHz. The connectors are widely used in communications, antennas,
radars and other applications for modules interconnections. It is also normally used in
conjunction with appropriate transmission line.
It describes the interface dimensions for general purpose connectors with gauging information
and the mandatory tests selected from IEC 61169-1, applicable to all detail specifications
relative to type SBMA connectors.
This specification indicates the recommended performance characteristics to be considered
when writing a DS and covers all tests schedules and inspection requirements.
NOTE Dimension are in mm, however original dimensions were in inches.
All un-dimensioned pictorial configurations are for reference purpose only.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61169-1:2013, Radio-frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 62037-3, Passive RF and microwave devices, intermodulation level measurement –
Part 3: Measurement of passive intermodulation in coaxial connectors

---------------------- Page: 12 ----------------------

SIST EN 61169-58:2017
IEC 61169-58:2016  IEC 2016 – 7 –
3 Mating face and gauge information
3.1 Dimensions – General connectors
3.1.1 Connector with socket centre contact
Mechanical and electrical reference plane
f
n
10°
60°
e
Detail for pin contact
1)
Seal
IEC


a) Air dielectric
Mechanical and electrical reference plane
f
e
IEC

b) PTFE dielectric
1)
 The design and location of the O-ring seal is optional, but it shall ensure the environmental performance
requirements are met.
Air dielectric and polytetrafluorethylene (PFTE) dielectric are optional according to the applications.
Figure 1 – Connector with pin centre contact (for dimensions, see Table 1)
ød
øc
øb
ød
øc
øb
øa
øm
øl
øk

---------------------- Page: 13 ----------------------

SIST EN 61169-58:2017
– 8 – IEC 61169-58:2016  IEC 2016
Table 1 – Dimensions of connector with pin-centre contact
Ref. mm
Min. Max.
a 0,86 0,88
b 2,78 (nom.)
c 3,18 3,32
d 3,51 3,56
e 3,25 3,35
f 5,03 –
k 0,10 0,20
l 0,50 0,53
m 1,19 1,23
n – 2,54

3.1.2 Connector with socket-centre contact
Interface of connector with socket-centre contact is shown in Figure 2, dimensions are shown
in Table 2.
Mechanical and electrical reference plane Mechanical and electrical reference plane
e
p
n
j g
(Note1)
45°
f (Note2)
Detail of socket Contact
IEC

Note 1 The outer hoop is optional for some applications.
Note 2 With spring finger bottomed.
Figure 2 – Connector with socket centre contact (for dimensions, see Table 2)
øb
øc
ød
øh
øm
øl

---------------------- Page: 14 ----------------------

SIST EN 61169-58:2017
IEC 61169-58:2016  IEC 2016 – 9 –
Table 2 – Dimensions of connector with socket-centre contact
Ref. mm
Min. Max.
b 2,78 (nom.)

a
c – –
d 3,90 3,96
e 3,12 3,22
f – 5,03
g 0,38 0,44
h 5,40 –
j 0,04 0,06
b
l – –
m 1,19 1,23
n 3,00 –
p 2,80 –
a
Shape of flange is optional, but should meet electrical and mechanical requirements.
b
Slot design optional, but the dimensions are to meet VSWR mating characteristics and connector durability
when mated with 0,50 mm to 0,53 mm diameter pin.

3.2 Gauges for general purpose connectors
3.2.1 Gauge pins for socket centre contact
Gauge pins for socket-centre contact is shown in Figure 3, dimensions are shown in Table 3.
Dimensions in millimetres
≤R0,4
b
0,4
90°
IEC

Figure 3 – Gauge pin for socket-centre contact (for dimensions, see Table 3)
Table 3 – Gauge pins dimensions for socket-centre contact
Ref. Gauge A Gauge B Gauge C
(For sizing purpose) (For insertion purpose) (For retention purpose)
+2
Mass of gauge: 14 g
0
mm mm mm
Min. Max. Min. Max. Min. Max.
a 0,533 0,536 0,528 0,531 0,495 0,500
b 0,76 1,14 1,27 1,91 1,27 1,91
Material: steel, polished.


øa

---------------------- Page: 15 ----------------------

SIST EN 61169-58:2017
– 10 – IEC 61169-58:2016  IEC 2016
3.2.2 Test procedure
a) Sizing test
The gauge A should be inserted into the centre contact for three times, this is a sizing
operation.
b) Withdrawal test
After this, the gauge B shall be inserted into socket-centre contact. The contact shall retain
the mass of the gauge B in a vertical downward position.
c) Additional test – Insertion test
Following the sizing operation, and if prescribed in the detail specification, the force
necessary to insert gauge A fully into the female centre contact shall be measured. When this
test is required, the maximum permitted insertion force shall then be specified and shall not
exceed 14 N.
3.2.3 Gauge pins for outer contact
Gauge pins for outer-centre contact is shown in Figure 4, dimensions are shown in Table 4.
D
0,4
E
IEC

Figure 4 – Gauge pin for outer contact (for dimensions, see Table 4)
Table 4 – Gauge pins dimensions for outer contact
Ref. Gauge A Gauge B Gauge C
(For sizing purposes) (For insertion purpose) (For retention purpose )
+2
Mass of gauge: 80 g
0
mm mm mm
Min. Max. Min. Max. Min. Max.
A 3,568 3,575 3,51 3,56 3,505 3,51
B 3,18 3,32 3,18 3,32 3,175 3,19
C 2,76 2,80 2,76 2,80 2,76 2,80
10°30′ 11°30′ 10°30′ 11°30′ 8°30′ 9°30′
D
E 3,50 4,0 3,5 – 3,5 –
Material: Steel, polished.


øA
øB
øC

---------------------- Page: 16 ----------------------

SIST EN 61169-58:2017
IEC 61169-58:2016  IEC 2016 – 11 –
3.2.4 Test procedure
a) Sizing test
The gauge A should be inserted into the centre contact one times, this is a sizing operation.
b) Withdrawal test
After this, the gauge B shall be inserted into socket-centre contact. The contact shall retain
the mass of the gauge B in a vertical downward position.
c) Additional test – Insertion test
Following the sizing operation, and if prescribed in the detail specification, the force
necessary to insert gauge A fully into the female centre contact shall be measured. When this
test is required, the maximum permitted insertion force shall then be specified and shall not
exceed 14 N.
3.3 Dimensions – standard test connectors – grade 0
3.3.1 Connector with pin-centre contact
Interface of connector with pin-centre contact is shown in Figure 5, dimensions are shown in
Table 5.
Mechanical and electrical reference plane
f
10°
A B
n
60°
ø0,05 B
e
0,015 A
Detail for pin contact
IEC

Figure 5 – Connector with pin centre contact (for dimensions, see Table 5)
Table 5 – Dimensions of connector with pin-centre contact
Ref. mm
Min. Max.
b
2,765 2,795
c 3,18 3,32
d 3,51 3,56
e 3,25 3,35
f 5,03 –
k 0,10 0,20
l 0,50 0,53
m 1,20 1,22
– 2,54
n

ød
øc
øb
øm
øl
øk

---------------------- Page: 17 ----------------------

SIST EN 61169-58:2017
– 12 – IEC 61169-58:2016  IEC 2016
3.3.2 Connector with socket-centre contact
Interface of connector with socket-centre contact is shown in Figure 6, dimensions are shown
in Table 6.
Mechanical and electrical reference plane
0,015 B
Mechanical and electrical reference plane
e
A
p
ø0,025 A
n
(Note1)
B
Detail of socket contact
j f (Note2)
IEC


Note 1 The outer hoop is optional for some applications.
Note 2 With spring finger bottomed.
Figure 6 – Connector with socket centre contact (for dimensions, see Table 6)
Table 6 – Dimensions of connector with socket-centre contact
Ref. mm
Min. Max.
b 2,765 2,795

a
c – –
d 3,90 3,96
e 3,12 3,22
f – 5,03
h 5,40 –
0,04 0,06
j

b
l – –
m 1,20 1,22
n 3,00 –
p 2,80 –
a
Shape of flange is optional, but should meet electrical and mechanical requirements.
b
Slot design optional, but the dimensions are to meet VSWR mating characteristics and connector durability
when mated with 0,50 mm to 0,53 mm diameter pin.

3.4 Requirements for installation
3.4.1 Radial misalignment
The location of the mountings of each pair of mating connectors shall be defined relative to a
common datum, such as the centre line of a dowel/dowel hole or “reference connector pair”.
The location shall be controlled to ensure that at the point of initial engagement, the radial
misalignment of the centre lines of the mating connectors from their true position does not
exceed the following limits (see Figure 7):
øb
øc
ød
øh
øm
øl

---------------------- Page: 18 ----------------------

SIST EN 61169-58:2017
IEC 61169-58:2016  IEC 2016 – 13 –
IEC
IEC


a) Rigidly mounted: receptacle and jack b) Rigidly mounted: receptacle and float mounted jack
Radial misalignment 0,076 mm max. Radial misalignment 0,51 mm max.
Figure 7 – Radial misalignment
3.4.2 Axial separation between mating reference planes
3.4.2.1 Rigidly mounted receptacle and jack
To maintain the electrical and environmental performances, the connector reference planes
should be within 0,38 mm max. as shown Figure 8.
Dimensions in millimetres
Ref. plane
≤0,38
IEC

Figure 8 – Rigidly mounted receptacle and jack
3.4.2.2 Rigidly mounted receptacle and float mounted jack
The float mounting allows a total of 1,52 mm axial travel. The mounting arrangements should
however ensure a minimum length of travel of 0,25 mm (0,76 mm preferred) to ensure full
length of engagement is maintained, under operational conditions as Figure 9.
A
A

---------------------- Page: 19 ----------------------

SIST EN 61169-58:2017
– 14 – IEC 61169-58:2016  IEC 2016
Dimensions in millimetres
≥0,25 (1,52 axial travel)
Spring mechanism
Fully mated ref. plane
IEC

Figure 9 – Rigidly mounted receptacle and float mounted jack
4 Quality assessment procedures
4.1 General
Subclauses 4.1 to 4.4 provide recommended ratings, performance and test conditions to be
considered when writing a detail specification (DS). They also provide an appropriate
schedule of tests with minimum levels of conformance inspection sampling, together with the
pro forma blank detail specification (BDS) and instructions for the preparation of a detail
specification.
4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013)
The values indicated below are recommended for SBMA series RF connectors and are given
for the writer of the detail specification. They are applicable for the condition when the
connectors are fully mated.
Certain tests will usually not be required. When these tests are required, appropriate values
shall be entered in the detail specification at the discretion of the specification writer.
Rating and characteristics are given in Table 7.

---------------------- Page: 20 ----------------------

SIST EN 61169-58:2017
IEC 61169-58:2016  IEC 2016 – 15 –
Table 7 – Rating and characteristics
Ratings and IEC 61169-1:2013 Value Remarks, deviation from
characteristics subclause standard test method
Test method
Electrical

Nominal Impedance
...