SIST EN ISO 11963:2019
(Main)Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO 11963:2019)
Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO 11963:2019)
This document specifies the requirements for solid, flat extruded sheets of polycarbonate (PC) for general applications. It applies specifically to sheets made of poly(p,p'-isopropylidene-diphenyl carbonate). The sheets can be coloured or colourless, and they can be transparent, translucent or opaque. The sheets can also be those that have a special weather-protective layer on one or both surfaces. This document applies only to thicknesses equal to or greater than 1,5 mm.
Kunststoffe - Tafeln aus Polycarbonat - Lieferformen, Abmessungen und charakteristische Eigenschaften (ISO 11963:2019)
Dieses Dokument legt die Anforderungen an feste, flach extrudierte Tafeln aus Polycarbonat (PC) für allgemeine Anwendungen fest. Es gilt insbesondere für Tafeln aus Poly(p,p'-Isopropylidendiphenylcarbonat). Die Tafeln können eingefärbt oder farblos, transparent, transluzent oder undurchsichtig sein. Die Tafeln können auf einer oder beiden Seiten eine Wetterschutzschicht besitzen.
Dieses Dokument gilt nur für Dicken gleich oder größer 1,5 mm.
Plastiques - Plaques en polycarbonate - Types, dimensions et caractéristiques (ISO 11963:2019)
Le présent document spécifie les exigences relatives aux plaques extrudées pleines, planes en polycarbonate (PC) pour usage général. Elle s'applique en particulier aux plaques faites à partir de poly(p,p'-isopropylidène-diphényl carbonate). Les plaques peuvent être colorées ou incolores et elles peuvent être transparentes, translucides ou opaques. Il peut également s'agir de plaques possédant une couche superficielle spéciale résistante au vieillissement sur une face ou sur les deux faces.
Le présent document s'applique uniquement aux épaisseurs supérieures ou égales à 1,5 mm.
Polimerni materiali - Plošče iz polikarbonata - Vrste, mere in značilnosti (ISO 11963:2019)
Ta dokument določa zahteve za trdne, ploščate ekstrudirane plošče iz polikarbonata (PC) za splošno uporabo. Navezuje se zlasti na plošče iz poli(p,p'-izopropiliden-difenil-karbonata). Plošče so lahko barvne ali brezbarvne, prozorne, prosojne ali neprozorne. Plošče imajo lahko tudi posebno zaščitno prevleko pred vremenskimi vplivi na eni površini ali obeh. Ta dokument se uporablja le za debelino 1,5 mm ali več.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11963:2019
01-november-2019
Nadomešča:
SIST EN ISO 11963:2014
Polimerni materiali - Plošče iz polikarbonata - Vrste, mere in značilnosti (ISO
11963:2019)
Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO
11963:2019)
Kunststoffe - Tafeln aus Polycarbonat - Lieferformen, Abmessungen und
charakteristische Eigenschaften (ISO 11963:2019)
Plastiques - Plaques en polycarbonate - Types, dimensions et caractéristiques (ISO
11963:2019)
Ta slovenski standard je istoveten z: EN ISO 11963:2019
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 11963:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11963:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 11963:2019
EN ISO 11963
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2019
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 11963:2012
English Version
Plastics - Polycarbonate sheets - Types, dimensions and
characteristics (ISO 11963:2019)
Plastiques - Plaques en polycarbonate - Types, Kunststoffe - Tafeln aus Polycarbonat - Lieferformen,
dimensions et caractéristiques (ISO 11963:2019) Abmessungen und charakteristische Eigenschaften
(ISO 11963:2019)
This European Standard was approved by CEN on 20 July 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11963:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11963:2019
EN ISO 11963:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11963:2019
EN ISO 11963:2019 (E)
European foreword
This document (EN ISO 11963:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2020, and conflicting national standards shall
be withdrawn at the latest by March 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11963:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11963:2019 has been approved by CEN as EN ISO 11963:2019 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11963:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 11963:2019
INTERNATIONAL ISO
STANDARD 11963
Third edition
2019-07
Plastics — Polycarbonate sheets —
Types, dimensions and characteristics
Plastiques — Plaques en polycarbonate — Types, dimensions et
caractéristiques
Reference number
ISO 11963:2019(E)
©
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 11963:2019
ISO 11963:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11963:2019
ISO 11963:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Composition . 2
5 Requirements . 2
5.1 Masking . 2
5.2 Appearance . 2
5.3 Colour . 2
5.4 Dimensions . 2
5.4.1 Conditions of measurement . 2
5.4.2 Length and width . 2
5.4.3 Deviation of shape from rectangular . 3
5.4.4 Thickness . 3
5.5 Shrinkage . 3
5.6 Basic properties . 3
5.7 Weathering behaviour . 3
5.8 Other properties . 4
6 Test methods . 4
6.1 General . 4
6.1.1 Sampling. 4
6.1.2 Conditioning and testing of specimens . 4
6.1.3 Preparation of specimens . 4
6.2 Colour . 4
6.3 Dimensions . 5
6.4 Mechanical properties . 5
6.5 Thermal properties . 6
6.6 Optical properties . 6
6.7 Weathering behaviour . 6
6.7.1 Natural weathering . 6
6.7.2 Artificial-weathering tests . 6
7 Reaction to fire . 6
8 Use in contact with food . 6
9 Retest and rejection . 7
Annex A (normative) Determination of change in dimensions at elevated temperature
(shrinkage) . 8
Bibliography .10
© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11963:2019
ISO 11963:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This third edition cancels and replaces the second edition (ISO 11963:2012), which has been technically
revised. The main changes compared to the previous edition are as follows.
— Relative humidity rule (50 ± 10) % was deleted from 5.4.1. Dimension change by the moisture
absorption is very small, and the polycarbonate materials do not need to state adjustment of the
relative humidity in the dimensional measurement.
— Relative humidity rule was changed from (65 ± 5) % to (50 ± 10) % in 6.7.2. Polycarbonate materials
are not humidity sensitive material in weathering.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11963:2019
INTERNATIONAL STANDARD ISO 11963:2019(E)
Plastics — Polycarbonate sheets — Types, dimensions and
characteristics
1 Scope
This document specifies the requirements for solid, flat extruded sheets of polycarbonate (PC) for
general applications. It applies specifically to sheets made of poly(p,p′-isopropylidene-diphenyl
carbonate). The sheets can be coloured or colourless, and they can be transparent, translucent or
opaque. The sheets can also be those that have a special weather-protective layer on one or both
surfaces.
This document applies only to thicknesses equal to or grea
...
SLOVENSKI STANDARD
oSIST prEN ISO 11963:2018
01-september-2018
3ROLPHUQLPDWHULDOL3ORãþHL]SROLNDUERQDWD9UVWHPHUHLQ]QDþLOQRVWL ,62',6
Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO/DIS
11963:2018)
Kunststoffe - Tafeln aus Polycarbonat - Lieferformen, Abmessungen und
charakteristische Eigenschaften (ISO/DIS 11963:2018)
Plastiques - Plaques en polycarbonate - Types, dimensions et caractéristiques (ISO/DIS
11963:2018)
Ta slovenski standard je istoveten z: prEN ISO 11963
ICS:
83.140.10 Filmi in folije Films and sheets
oSIST prEN ISO 11963:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 11963:2018
---------------------- Page: 2 ----------------------
oSIST prEN ISO 11963:2018
DRAFT INTERNATIONAL STANDARD
ISO/DIS 11963
ISO/TC 61/SC 11 Secretariat: JISC
Voting begins on: Voting terminates on:
2018-06-05 2018-08-28
Plastics — Polycarbonate sheets — Types, dimensions and
characteristics
Plastiques — Plaques en polycarbonate — Types, dimensions et caractéristiques
ICS: 83.140.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 11963:2018(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2018
---------------------- Page: 3 ----------------------
oSIST prEN ISO 11963:2018
ISO/DIS 11963:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 11963:2018
ISO/DIS 11963:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Composition . 2
5 Requirements . 2
5.1 Masking . 2
5.2 Appearance . 3
5.3 Colour . 3
5.4 Dimensions . 3
5.4.1 Conditions of measurement . 3
5.4.2 Length and width . 3
5.4.3 Deviation of shape from rectangular . 3
5.4.4 Thickness . 3
5.5 Shrinkage . 4
5.6 Basic properties . 4
5.7 Weathering behaviour . 4
5.8 Other properties . 4
6 Test methods . 4
6.1 General . 4
6.1.1 Sampling. 4
6.1.2 Conditioning and testing of specimens . 5
6.1.3 Preparation of specimens . 5
6.2 Colour . 5
6.3 Dimensions . 5
6.4 Mechanical properties . 6
6.5 Thermal properties . 6
6.6 Optical properties . 6
6.7 Weathering behaviour . 6
6.7.1 Natural weathering . 6
6.7.2 Artificial-weathering tests . 6
7 Reaction to fire . 7
8 Use in contact with food . 7
9 Retest and rejection . 7
Annex A (normative) Determination of change in dimensions at elevated temperature
(shrinkage) . 8
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 11963:2018
ISO/DIS 11963:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/iso/foreword .html.
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This third edition cancels and replaces the second edition (ISO 11963:2012), which has been technically
revised.
iv © ISO 2018 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 11963:2018
DRAFT INTERNATIONAL STANDARD ISO/DIS 11963:2018(E)
Plastics — Polycarbonate sheets — Types, dimensions and
characteristics
1 Scope
This International Standard specifies the requirements for solid, flat extruded sheets of polycarbonate
(PC) for general applications. It applies specifically to sheets made of poly(p,p′-isopropylidene-diphenyl
carbonate). The sheets may be coloured or colourless, and they may be transparent, translucent or
opaque. The sheets may also have a special weather-protective layer on one or both surfaces.
This International Standard applies only to thicknesses equal to or greater than 1,5 mm.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 62:2008, Plastics — Determination of water absorption
ISO 75-1, Plastics — Determination of temperature of deflection under load — Part 1: General test method
ISO 75-2:2004, Plastics — Determination of temperature of deflection under load — Part 2: Plastics
and ebonite
ISO 179-1:2010, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented
impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 306:2004, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 489:1999, Plastics — Determination of refractive index
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 877-1, Plastics — Methods of exposure to solar radiation — Part 1: General guidance
ISO 877-2, Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure
behind window glass
ISO 877-3, Plastics — Methods of exposure to solar radiation — Part 3: Intensified weathering using
concentrated solar radiation
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection
ISO 2859-10, Sampling procedu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.