SIST EN 15433-1:2008

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Transportation loads - Measurement and analysis of dynamic mechanical loads - Part 1: General requirementsNLKCharges de transport - Mesurage et analyse des charges mécaniques dynamiques - Partie 1 : Exigences généralesTransportbelastungen - Messen und Auswerten von mechanisch-dynamischen Belastungen - Teil 1: Allgemeine AnforderungenTa slovenski standard je istoveten z:EN 15433-1:2007SIST EN 15433-1:2008en,de55.180.01ICS:SLOVENSKI
STANDARDSIST EN 15433-1:200801-februar-2008







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15433-1December 2007ICS 55.180.01 English VersionTransportation loads - Measurement and evaluation of dynamicmechanical loads - Part 1: General requirementsCharges de transport - Mesurage et analyse des chargesmécaniques dynamiques - Partie 1 : Exigences généralesTransportbelastungen - Messen und Auswerten vonmechanisch-dynamischen Belastungen - Teil 1: AllgemeineAnforderungenThis European Standard was approved by CEN on 28 October 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15433-1:2007: E



EN 15433-1:2007 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Requirements.5 3.1 Fundamental requirements.5 3.2 Location of measuring points.5 3.3 Source data.6 3.4 Care during data acquisition and documentation.6 3.5 Measuring report.6 3.6 Measurement on a transported item.6 3.7 Data validity check.6 3.8 Data analysis.6 3.9 Derivation of test specifications.7 3.10 Transportation monitoring with automatic recording equipment.7 Bibliography.8



EN 15433-1:2007 (E) 3 Foreword This document (EN 15433-1:2007) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by June 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.



EN 15433-1:2007 (E) 4 Introduction This standard was originally prepared by working group NAVp-1.4, Requirements and Testing, of the German Standardisation Institute (DIN). It is part of a complete normative concept to acquire and describe the loads acting on goods and influencing them during transport, handling and storage. This standard becomes significant when related to the realisation of the European Directive on Packaging and Packaging Waste (Directive 94/62 EC, 20 December 1994). This directive specifies requirements on the avoidance or reduction of packaging waste, and requires that the amount of packaging material is adjusted to the expected transportation load, in order to protect the transportation item adequately. However, this presumes some knowledge of the transportation loads occurring during shipment. At present, basic standards, based on scientifically confirmed values, which can adequately describe and characterize the magnitudes of transportation loads, especially in the domain of dynamic-mechanical loads, do not exist nationally or internationally. Reasons for this are mainly the absence of published data, insufficient description of the measurements, or restrictions on the dissemination of this information. This standard will enable the measurement and evaluation of dynamic mechanical transportation loads, thus enabling the achievement of standardized and adequately documented load values. This series of standards consists of the following parts:  Part 1: General requirements
 Part 2: Data acquisition and general requirements for measuring equipment  Part 3: Data validity check and data editing for evaluation  Part 4: Data evaluation
 Part 5: Derivation of test specifications
 Part 6: Automatic recording systems for measuring randomly occurring shock during monitoring of transports. This standard describes the basics and principles to be
...