Fixed firefighting systems - Components for gas extinguishing systems - Part 8: Requirements and test methods for connectors

This European Standard specifies product characteristics and describes test methods for flexible and rigid connectors intended to be used in gas extinguishing systems (i.e. CO2, Inert Gas or Halocarbon gas) installed in buildings as a part of a complete operating system.
This European Standard is applicable to the following connectors:
—   Type 1 and Type 5: used between container valves and the manifold;
—   Type 3: used in pneumatic pilot lines;
—   Type 2 and Type 4: used in distribution pipework of fire extinguishing installations downstream of the manifold/selector valve.

Ortsfeste Brandbekämpfungsanlagen - Bauteile für Löschanlagen mit gasförmigen Löschmitteln - Teil 8: Anforderungen und Prüfverfahren für Verbindungen

Diese Europäische Norm legt Produkteigenschaften fest und beschreibt Prüfverfahren für flexible und starre Verbindungen, die in Löschanlagen mit gasförmigen Löschmitteln (d. h. CO2-, Inertgas-Feuerlöschanlagen und Feuerlöschanlagen mit halogenierten Kohlenwasserstoffen) eingesetzt werden, welche in Gebäuden als Teil eines vollständigen Betriebssystems installiert sind.
Dieses Dokument gilt für die folgenden Verbindungen:
-   Typ 1 und Typ 5: verwendet zwischen Behälterventilen und dem Sammelrohr
-   Typ 3: verwendet in pneumatischen Steuerleitungen
-   Typ 2 und Typ 4: verwendet in Düsenrohrnetzen von Löschanlagen hinter dem Sammelrohr/dem Bereichsventil.

Installations fixes de lutte contre l'incendie - Élements constitutifs des installations d'extinction à gaz - Partie 8 : Exigences et méthodes d'essai pour raccords

La présente Norme européenne spécifie les caractéristiques du produit et décrit les méthodes d’essai concernant les raccords flexibles et rigides destinés à être utilisés dans les installations d'extinction à gaz (c'est-à-dire au CO2, à gaz inerte ou à gaz inhibiteur) équipant les bâtiments sous forme de système complet.
La présente Norme européenne s’applique aux raccords suivants :
-   Type 1 et Type 5 : utilisés entre les vannes du réservoir et le collecteur ;
-   Type 3 : utilisé dans les canalisations pilotes pneumatiques ;
-   Type 2 et Type 4 : utilisés dans le réseau d’alimentation des installations d’extinction, en aval du collecteur ou de la vanne directionnelle.

Vgrajeni gasilni sistemi - Sestavni deli sistemov za gašenje s plinom - 8. del: Zahteve in preskusne metode za spoje

General Information

Status
Not Published
Public Enquiry End Date
29-Jul-2016
Technical Committee
Current Stage
5020 - Formal vote (FV) (Adopted Project)
Start Date
05-Aug-2024
Due Date
23-Sep-2024
Completion Date
05-Aug-2024

Relations

Buy Standard

Draft
prEN 12094-8:2016
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
oSIST prEN 12094-8:2016
01-julij-2016
Vgrajeni gasilni sistemi - Sestavni deli sistemov za gašenje s plinom - 8. del:
Zahteve in preskusne metode za spoje
Fixed firefighting systems - Components for gas extinguishing systems - Part 8:
Requirements and test methods for connectors
Ortsfeste Brandbekämpfungsanlagen - Bauteile für Löschanlagen mit gasförmigen
Löschmitteln - Teil 8: Anforderungen und Prüfverfahren für Verbindungen
Installations fixes de lutte contre l'incendie - Élements constitutifs des installations
d'extinction à gaz - Partie 8 : Exigences et méthodes d'essai pour raccords
Ta slovenski standard je istoveten z: prEN 12094-8
ICS:
13.220.10 Gašenje požara Fire-fighting
oSIST prEN 12094-8:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 12094-8:2016
oSIST prEN 12094-8:2016
DRAFT
EUROPEAN STANDARD
prEN 12094-8
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2016
ICS 13.220.20 Will supersede EN 12094-8:2006
English Version
Fixed firefighting systems - Components for gas
extinguishing systems - Part 8: Requirements and test
methods for connectors
Installations fixes de lutte contre l'incendie - Élements Ortsfeste Brandbekämpfungsanlagen - Bauteile für
constitutifs des installations d'extinction à gaz - Partie Löschanlagen mit gasförmigen Löschmitteln - Teil 8:
8 : Exigences et méthodes d'essai pour raccords Anforderungen und Prüfverfahren für Verbindungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 191.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12094-8:2016 E
worldwide for CEN national Members.

oSIST prEN 12094-8:2016
prEN 12094-8:2016 (E)
Contents Page
European Foreword . 3
1 Scope . 4
2 Terms and definitions . 4
3 Product characteristics . 5
3.1 Operational reliability and Performance under fire condition. 5
3.2 Durability of Operational reliability and Performance under fire condition . 6
3.2.1 Material specification (metal parts). 6
3.2.2 Resistance to bursting (all types) . 6
3.2.3 Resistance to pressure and heat (only type 2 and 4) . 6
3.2.4 Resistance to heat and cold shock (only type 2 and 4 for CO ) . 6
3.2.5 Resistance to cold (only type 1, 2, 3 and 4) . 6
3.2.6 Resistance of type 2 connectors to flexing (only type 2) . 7
4 Testing, assessment and sampling methods . 7
4.1 Conditions . 7
4.2 Samples . 7
4.3 Compliance . 8
4.4 Operational reliability and Performance under fire conditions. 8
4.5 Durability of Operational reliability and Performance under fire condition . 8
4.5.1 Material specification (metal parts). 8
4.5.2 Resistance to bursting (all types) . 8
4.5.3 Resistance to pressure and heat (only type 2 and 4) . 8
4.5.4 Resistance to heat and cold shock (only type 2 and 4 for CO ) . 8
4.5.5 Resistance to cold (only type 1, 2, 3 and 4) . 9
4.5.6 Resistance to flexing (only type 2) . 9
5 Marking, labelling and packaging . 9
6 Assessment and verification of constancy of performance -AVCP . 9
6.1 General . 9
6.2 Type testing . 9
6.2.1 General . 9
6.2.2 Test samples, testing and compliance criteria . 10
6.2.3 Test reports . 10
6.2.4 Shared other party results . 10
6.3 Factory production control (FPC) . 11
6.3.1 General . 11
6.3.2 Requirements . 11
6.3.3 Product specific requirements . 13
6.3.4 Initial inspection of factory and of FPC . 14
6.3.5 Continuous surveillance of FPC . 15
6.3.6 Procedure for modifications . 15
6.3.7 Pre-production products (e.g. prototypes) . 15
Annex A (informative) Documentation . 17
Annex ZA (informative) Relationship of this European Standard with Regulation (EU)
No. 305/2011 . 18

oSIST prEN 12094-8:2016
prEN 12094-8:2016 (E)
European foreword
This document (prEN 12094-8:2016) has been prepared by Technical Committee CEN/TC 191 “Fixed
firefighting systems”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12094-8:2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of Regulation (EU) 305/2011.
For relationship with Regulation (EU) 305/2011, see informative Annex ZA, which is an integral part of
this document.
EN 12094, Fixed firefighting systems - Components for gas extinguishing systems consists of the following
parts:
— Part 1: Requirements and test methods for electrical automatic control and delay devices
— Part 2: Requirements and test methods for non-electrical automatic control and delay devices
— Part 3: Requirements and test methods for manual triggering and stop devices
— Part 4: Requirements and test methods for container valve assemblies and their actuators
— Part 5: Requirements and test methods for high and low pressure selector valves and their actuators
— Part 6: Requirements and test methods for non-electrical disable devices
— Part 7: Requirements and test methods for nozzles
— Part 8: Requirements and test methods for connectors
— Part 9: Requirements and test methods for special fire detectors
— Part 10: Requirements and test methods for pressure gauges and pressure switches
— Part 11: Requirements and test methods for mechanical weighing devices
— Part 12: Requirements and test methods for pneumatic alarm devices
— Part 13: Requirements and test methods for check valves and non-return valves
— Part 16: Requirements and test methods for odorizing devices for CO low pressure systems
NOTE This list includes standards that are in preparation and other standards may be added. For current
status of published standards, refer to www.cen.eu.
oSIST prEN 12094-8:2016
prEN 12094-8:2016 (E)
1 Scope
This European Standard specifies product characteristics and describes test methods for flexible and
rigid connectors intended to be used in gas extinguishing systems (i.e. CO , inert gas or halocarbon gas)
installed in buildings as a part of a complete operating system.
This European Standard is applicable to the following connectors:
— Type 1 and Type 5: used between container valves and the manifold;
— Type 3: used in pneumatic pilot lines;
— Type 2 and Type 4: used in distribution pipework of fire extinguishing installations downstream of
the manifold/selector valve.
2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
2.1
CO -high-pressure installation
fire extinguishing installation in which the CO is stored at ambient temperature
EXAMPLE The pressure of the CO in storage is p = 58,6 bar at 21 °C.
2 abs
2.2
CO -low-pressure installation
fire extinguishing installation in which the CO is stored at low temperature
Note 1 to entry: Normally −19 °C to −21 °C.
2.3
fill ratio
the mass of extinguishing medium related to the net capacity of a container
Note 1 to entry: Expressed as kilogram per litre (kg/l).
2.4
flexible connector
link between two parts which are subject to relative movement or subject to tolerances
2.5
halocarbon gas
extinguishing agent that contains as primary components one or more organic compounds containing
one or more of the elements fluorine, chlorine, bromine or iodine
2.6
halocarbon gas installation
fire extinguishing installation in which the halocarbon gas is stored at ambient temperature
2.7
inert gas
non liquefied gas or mixture of gases which extinguish the fire mainly by reducing the oxygen-
concentration in the protected zone
EXAMPLE Argon, nitrogen or mixtures of these gases with CO .
oSIST prEN 12094-8:2016
prEN 12094-8:2016 (E)
2.8
inert gas installation
fire extinguishing installation in which the inert gas is stored at ambient temperature
2.9
type 1 connector
flexible connector for connecting containers to a manifold
2.10
type 2 connector
flexible connector for use in distribution pipework downstream the manifold or selector valve for the
connection of moving parts
2.11
type 3 connector
flexible connector for use in pneumatic pilot lines
2.12
type 4 connector
flexible connector for use in distribution pipework downstream the manifold or selector valve for the
connection of non-moving parts which allow for dimensional adjustments
2.13
type 5 connector
rigid connector for connecting containers to a manifold
2.14
working pressure
pressure at which the component is used in the system
3 Product characteristics
3.1 Operational reliability and performance under fire cond
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.