SIST EN 60384-16:2006

SLOVENSKI SIST EN 60384-16:2006

STANDARD
februar 2006
Nespremenljivi kondenzatorji za uporabo v elektronski opremi – 16. del:
Področna specifikacija: nespremenljivi kondenzatorji z dielektrikom iz
metalizirane polipropilenske folije za enosmerne napetosti (IEC 60384-
16:2005)
Fixed capacitors for use in electronic equipment – Part 16: Sectional specification:
Fixed metallized polypropylene film dielectric d.c. capacitors (IEC 60384-16:2005)
ICS 31.060.10 Referenčna številka
SIST EN 60384-16:2006(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 60384-16
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2005

ICS 31.060.30 Supersedes EN 131200:2002


English version


Fixed capacitors for use in electronic equipment
Part 16: Sectional specification:
Fixed metallized polypropylene film dielectric d.c. capacitors
(IEC 60384-16:2005)


Condensateurs fixes utilisés  Festkondensatoren zur Verwendung in
dans les équipements électroniques Geräten der Elektronik
Partie 16: Spécification intermédiaire: Teil 16: Rahmenspezifikation:
Condensateurs fixes pour courant continu Festkondensatoren mit metallisierter
à diélectrique en film de polypropylène Polypropylen-Folie als Dielektrikum für
métallisé Gleichspannung
(CEI 60384-16:2005) (IEC 60384-16:2005)


This European Standard was approved by CENELEC on 2005-11-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60384-16:2005 E

---------------------- Page: 2 ----------------------

EN 60384-16:2005 - 2 -
Foreword
The text of document 40/1595/FDIS, future edition 2 of IEC 60384-16, prepared by IEC TC 40,
Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as EN 60384-16 on 2005-11-01.
This European Standard supersedes EN 131200:2002.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-08-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-11-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60384-16:2005 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60065 NOTE Harmonized as EN 60065:2002 (modified).
IEC 60384-14 NOTE Harmonized as EN 60384-14:2005 (not modified).
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60384-16:2005
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60063 1963 Preferred number series for resistors and - -
capacitors
A1 1967 - -
A2 1977 - -

1) 2)
IEC 60068-1 - Environmental testing EN 60068-1 1994
Part 1: General and guidance

1) 2)
IEC 60384-1 - Fixed capacitors for use in electronic EN 60384-1 2001
(mod) equipment + corr. October 2001
Part 1: Generic specification

1) 2)
IEC 60384-16-1 - Part 16-1: Blank detail specification - EN 60384-16-1 2005
Fixed metallized polypropylene film
dielectric d.c. capacitors - Assessment
levels E and EZ

1)
IEC 60410 - Sampling plans and procedures for - -
inspection by attributes

1)
ISO 3 - Preferred numbers - Series of preferred - -
numbers




1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

INTERNATIONAL IEC


STANDARD 60384-16





QC 301200

Second edition
2005-11

Fixed capacitors for use in electronic equipment –
Part 16:
Sectional specification:
Fixed metallized polypropylene film
dielectric d.c. capacitors

 IEC 2005  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale U
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

---------------------- Page: 5 ----------------------

– 2 – 60384-16  IEC:2005(E)
CONTENTS

FOREWORD.4

1 General .7
1.1 Scope.7
1.2 Object .7
1.3 Normative references .7
1.4 Information to be given in a detail specification .8
1.5 Terms and definitions .9
1.6 Marking .10
2 Preferred ratings and characteristics .10
2.1 Preferred characteristics .10
2.2 Preferred values of ratings .10
3 Quality assessment procedures.11
3.1 Primary stage of manufacture.11
3.2 Structurally similar components.11
3.3 Certified records of released lots.11
3.4 Qualification approval.12
3.5 Quality conformance inspection.18
4 Test and measurement procedures.19
4.1 Visual examination and check of dimensions.19
4.2 Electrical tests.20
4.3 Robustness of terminations .23
4.4 Resistance to soldering heat .23
4.5 Solderability .23
4.6 Rapid change of temperature .23
4.7 Vibration.23
4.8 Bump .24
4.9 Shock.24
4.10 Climatic sequence .25
4.11 Damp heat, steady state.26
4.12 Endurance.26
4.13 Charge and discharge .26
4.14 Component solvent resistance.28
4.15 Solvent resistance of the marking.28

Bibliography.29

Table 1 – Preferred values.9
Table 2 – Preferred combinations .11
Table 3 – Sampling plan together with numbers of permissible defectives for
qualification approval tests .13
Table 4 – Test schedule for qualification approval.14
Table 5 – Lot-by-lot inspection .19
Table 6 – Periodic inspection .19

---------------------- Page: 6 ----------------------

60384-16  IEC:2005(E) – 3 –
Table 7 – Voltages to be applied.20
Table 8 – Measurement requirements .21
Table 9 – Insulation resistance requirements .21
Table 10 – Correction factors.22
Table 11 – Characteristics at lower category temperature .22
Table 12 – Characteristics at upper category temperature .22
Table 13 – Preferred severities .24
Table 14 – Test conditions.26
Table 15 – Lead spacing.27

---------------------- Page: 7 ----------------------

– 4 – 60384-16  IEC:2005(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 16: Sectional specification: Fixed metallized
polypropylene film dielectric d.c. capacitors


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-16 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This second edition cancels and replaces the first edition published in 1982, amendment 1
(1987) and amendment 2 (1992) and constitutes minor revisions related to tables, figures and
references.
The text of this standard is based on the following documents:
FDIS Report on voting
40/1595/FDIS 40/1628/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 8 ----------------------

60384-16  IEC:2005(E) – 5 –
IEC 60384 consists of the following parts, under the (new) general title Fixed capacitors for
use in electronic equipment:
Part 1: Generic specification
Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric
d.c. capacitors
Part 3: Sectional specification: Fixed tantalum chip capacitors
Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid
electrolyte
Part 5: Sectional specification: Fixed mica dielectric d.c. capacitors with a rated voltage
not exceeding 3000 V – Selection of methods of test and general requirements
Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c.
capacitors
Part 7: Sectional specification: Fixed polystyrene film dielectric metal foil d.c. capacitors
Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1
Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2
Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil
d.c. capacitors
Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c.
capacitors
Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c.
capacitors
Part 14: Sectional specification: Fixed capacitors for electromagnetic interference
suppression and connection to the supply mains
Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid
electrolyte
Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c.
capacitors
Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and
pulse capacitors
Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid and
non-solid electrolyte
Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric
chip d.c. capacitors
Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric chip
d.c. capacitors
Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic
dielectric, Class 1
Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic
dielectric, Class 2
Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphthalate
film dielectric d.c. capacitors
Part 24: Sectional specification – Surface mount fixed tantalum electrolytic capacitors with
conductive polymer solid electrolyte (under consideration)
Part 25: Sectional specification – Surface mount fixed aluminium electrolytic capacitors
with conductive polymer solid electrolyte (under consideration)
All sectional specifications mentioned above do have one or more blank detail specifications
being a supplementary document, containing requirements for style, layout and minimum
content of detail specifications.

---------------------- Page: 9 ----------------------

– 6 – 60384-16  IEC:2005(E)
The QC 301 200 number that appears on the front cover of this publication is the specification
number in the IECQ Quality Assessment System for Electronic Components.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

---------------------- Page: 10 ----------------------

60384-16  IEC:2005(E) – 7 –
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 16: Sectional specification: Fixed metallized
polypropylene film dielectric d.c. capacitors


1 General
1.1 Scope
This part of IEC 60384 applies to fixed capacitors with metallized electrodes and poly-
propylene dielectric for use in electronic equipment.
These capacitors may have "self-healing properties" depending on conditions of use. They
are mainly intended for use with direct voltage. Capacitors for alternating voltage and pulse
applications are not included, but are covered by IEC 60384-17.
The maximum power to be applied is 500 var at 50 Hz and the maximum peak voltage is 2 500 V.
Two performance grades of capacitors are covered, Grade 1 for long-life application and
Grade 2 for general application.
Capacitors for electromagnetic interference suppression are not included, but are covered by
IEC 60384-14.
Capacitors for electrical shock hazard protection (covered by IEC 60065) and fluorescent
lamp and motor capacitors (covered by IEC technical committee 33, and IEC technical
committee 34).
1.2 Object
The object of this standard is to prescribe preferred ratings and characteristics and to select
from IEC 60384-1 (1999) the appropriate quality assessment procedures, tests and measuring
methods and to give general performance requirements for this type of capacitor. Test
severities and requirements prescribed in detail specifications referring to this sectional
specification shall be of equal or higher performance level, because lower performance levels
are not permitted.
1.3 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60063:1963, Preferred number series for resistors and capacitors
Amendment 1 (1967)
Amendment 2 (1977)
IEC 60068-1, Environmental testing. Part 1: General and guidance
IEC 60384-1, Fixed capacitors for use in electronic equipment – Part 1: Generic specification
IEC 60384-16-1, Fixed capacitors for use in electronic equipment – Part 16: Blank detail
specification: Fixed metallized polypropylene film dielectric d.c. capacitors – Assessment level E
IEC 60410, Sampling plans and procedures for inspection by attributes
ISO 3, Preferred numbers – Series of preferred numbers

---------------------- Page: 11 ----------------------

– 8 – 60384-16  IEC:2005(E)
1.4 Information to be given in a detail specification
Detail specifications shall be derived from the relevant blank detail specification.
Detail specifications shall not specify requirements inferior to those of the generic, sectional
or blank detail specification. When more severe requirements are included, they shall be
listed in 1.9 of the detail specification and indicated in the test schedules, for example by an
asterisk.
NOTE  The information given in 1.4.1 may for convenience, be presented in tabular form.
The following information shall be given in each detail specification and the values quoted
shall preferably be selected from those given in the appropriate clause of this sectional
specification.
1.4.1 Outline drawing and dimensions
There shall be an illustration of the capacitor as an aid to easy recognition and for comparison
of the capacitor with others. Dimensions and their associated tolerances, which affect
interchangeability and mounting, shall be given in the detail specification. All dimensions shall
preferably be stated in millimetres.
Normally, the numerical values shall be given for the length of the body, the width and height
of the body and the wire spacing, or for cylindrical types, the body diameter, and the length
and diameter of the terminations. When necessary, for example when a number of items
(capacitance values/voltage ranges) are covered by a detail specification, the dimensions and
their associated tolerances shall be placed in a table below the drawing.
When the configuration is other than described above, the detail specification shall state such
dimensional information as will adequately describe the capacitor. When the capacitor is not
designed for use on printed boards, this shall be clearly stated in the detail specification
1.4.2 Mounting
The detail specification shall specify the method of mounting to be applied for normal use and
for the application of the vibration and the bump or shock tests. The capacitors shall be
mounted by their normal means. The design of the capacitor may be such that special
mounting fixtures are required in its use. In this case, the detail specification shall describe
the mounting fixtures and they shall be used in the application of the vibration and bump or
shock tests.
1.4.3 Ratings and characteristics
The ratings and characteristics shall be in accordance with the relevant clauses of this
specification, together with the following:
1.4.3.1 Rated capacitance range
See 2.2.1.
NOTE  When products approved to the detail specification may have different ranges, the following statement
should be added:
"The range of values available in each voltage range is given in IEC QC 001005.
1.4.3.2 Particular characteristics
Additional characteristics may be listed, when they are considered necessary to specify
adequately the component for design and application purposes.

---------------------- Page: 12 ----------------------

60384-16  IEC:2005(E) – 9 –
1.4.3.3 Soldering
The detail specification shall prescribe the test methods, severities and requirements
applicable for the solderability and the resistance to soldering heat test.
1.4.4 Marking
The detail specification shall specify the content of the marking on the capacitor and on the
package. Deviations from 1.6 of this sectional specification, shall be specifically stated.
1.5 Terms and definitions
For the purposes of this document, the terms and definitions of IEC 60384-1 and the following
apply.
1.5.1 Performance grades
1.5.1.1
performance grade 1 capacitors (long-life)
capacitors intended for long-life applications with stringent requirements for the electrical
parameters
1.5.1.2
performance grade 2 capacitors (general purpose)
capacitors for general application where the stringent requirements of performance grade 1
are not necessary
1.5.2
stability grade
capacitance drift after climatic and mechanical tests and after endurance tests
NOTE The performance grade and the stability grade shall be noted in the detail specification.
1.5.3
performance grade and stability grade combinations
see the table below for preferred values
Table 1 – Preferred values
Performance Stability Combination
grades grades designations
1 1.1
1
2 1.2
2 – 2
The three combinations of performance grades and stability grades concern capacitance stability
and tan δ values. Distinction in performance of the three combinations is shown in Table 4.
1.5.4
rated voltage
maximum d.c. voltage which may be applied continuously to a capacitor at the rated
temperature
NOTE  The sum of the d.c. voltage and the peak a.c. voltage applied to the capacitor must not exceed the rated
voltage. The value of the peak a.c. voltage allowed at different frequencies is under consideration.

---------------------- Page: 13 ----------------------

– 10 – 60384-16  IEC:2005(E)
1.6 Marking
See 2.4 of IEC 60384-1, with the following details:
1.6.1  The information given in the marking is normally selected from the following list; the
relative importance of each item is indicated by its position in the list:
a) rated capacitance;
b) rated voltage (d.c. voltage may be indicated by the symbol
– – – or     );
c) tolerance on rated capacitance;
d) year and month (or week) of manufacture;
e) manufacturer's name or trade mark;
f) climatic category;
g) manufacturer's type designation;
h) reference to the detail specification.
1.6.2  The capacitor shall be clearly marked with a), b) and c) above and with as many as
possible of the remaining items as is considered necessary. Any duplication of information in
the marking on the capacitor should be avoided.
1.6.3  The package containing the capacitor(s) shall be clearly marked with all the
information listed in 1.6.1.
1.6.4  Any additional marking shall be so applied that no confusion can arise.
2 Preferred ratings and characteristics
2.1 Preferred characteristics
The values given in detail specifications shall preferably be selected from the following:
2.1.1 Preferred climatic categories
The capacitors covered by this specification are classified into climatic categories according
to the general rules given in IEC 60068-1.
The lower and upper category temperatures and the duration of the damp heat, steady state
test shall be chosen from the following:
Lower category temperature:  –55 °C; –40 °C; –25 °C and –10 °C
Upper category temperature:  +70 °C; +85 °C; +100 °C and +105 °C
Duration of the damp heat, steady state test: 4; 10; 21 and 56 days
The severities for the cold and dry heat tests are the lower and upper category temperatures
respectively.
2.2 Preferred values of ratings
2.2.1 Rated capacitance (C )
R
Preferred values of
...