SIST EN 6069:2010

SLOVENSKI STANDARD
SIST EN 6069:2010
01-januar-2010
Aeronavtika - Kovice, 100° zmanjšana ugrezna glava, ozka toleranca - Colski tip
Aerospace series - Rivet, 100° reduced flush head, close tolerance - Inch series
Luft- und Raumfahrt - Vollniet, 100° Reduzierter Senkkopf, enge Toleranz - Zoll-Reihe
Série aérospatiale - Rivets de précision, 100° tête fraisée - Série en inches
Ta slovenski standard je istoveten z: EN 6069:2009
ICS:
49.030.60 Kovice Rivets
SIST EN 6069:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 6069:2010

---------------------- Page: 2 ----------------------

SIST EN 6069:2010


EUROPEAN STANDARD
EN 6069

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2009
ICS 21.060.40
English Version
Aerospace series - Rivet, 100° reduced flush head, close
tolerance - Inch series
Série aérospatiale - Rivets de précision, 100° tête fraisée - Luft- und Raumfahrt - Vollniet, 100° Reduzierter Senkkopf,
Série en inches enge Toleranz - Zoll-Reihe
This European Standard was approved by CEN on 6 October 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6069:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 6069:2010
EN 6069:2009 (E)
Contents Page
Foreword . 3
1 Scope . 4
2 Normative references . 4
3 Requirements . 5
4 Designation . 8
5 Marking . 9
6 Technical specification . 10

2

---------------------- Page: 4 ----------------------

SIST EN 6069:2010
EN 6069:2009 (E)
Foreword
This document (EN 6069:2009) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at
the latest by May 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

3

---------------------- Page: 5 ----------------------

SIST EN 6069:2010
EN 6069:2009 (E)
1 Scope
This European Standard specifies the dimensions, tolerances and mass of rivets with 100° reduced flush
head, close tolerance, inch series, for aerospace application.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 2115, Aerospace series — Aluminium alloy 2117-T42 — Wire for solid rivets — D ≤ 10 mm
EN 2116, Aerospace series — Aluminium alloy 2017A-T42 — Wire for solid rivets — D ≤ 10 mm
EN 2117, Aerospace series — Aluminium alloy AL-P5056A (5056A)-H32 — Wire for solid rivets — D ≤ 10 mm
EN 2424:2008, Aerospace series — Marking of aerospace products
EN 2941, Aerospace series — Nickel alloy rivets — Technical specification

EN 3115, Aerospace series — Aluminium alloy 7050- T73 — Wire for solid rivets — D ≤ 10mm
EN 4372, Aerospace series — Heat resisting nickel alloy with copper NI-PD9001 (NiCu31) — Wire for solid
rivets — D ≤ 10 mm
EN 6104, Aerospace series — Rivets, solid, in aluminium or aluminium alloy — Inch series — Technical
1)
specification

1)
EN 6118, Aerospace series — Process specification — Aluminium base protection for fasteners
ISO 8080, Aerospace — Anodic treatment of titanium and titanium alloys — Sulfuric acid process
2)
AMS 4982, Titanium alloy wire 44.5 Cb
3)
MIL-DTL-5541, Military specification, Chemical conversion coatings on aluminium and aluminium alloys
3)
MIL-A-8625, Military specification, Anodic coatings for aluminium and aluminium alloys
4)
NASM5674, Rivets, structural, aluminium alloy, titanium columbium alloy, general specification for
4)
NAS9800, Head protrusion gaging, 100° flush head fasteners, gage block, gage diameters and stylus

1) Published as ASD-STAN Prestandard at the date of publication of this standard by Aerospace and Defence
Industries Association of Europe-Standardization (ASD-STAN), (www.asd-stan.org).
2) Published by: Society of Automotive
...