SIST EN ISO 21627-1:2004

SLOVENSKI STANDARD
SIST EN ISO 21627-1:2004
01-februar-2004
1DGRPHãþD
SIST EN ISO 11376:2002
3ROLPHUQLPDWHULDOL(SRNVLGQHVPROH'RORþHYDQMHNORUD±GHO$QRUJDQVNL
NORU,62
Plastics - Epoxy resins - Determination of chlorine content Part 1: Inorganic chlorine (ISO
21627-1:2002)
Kunststoffe - Epoxidharze - Bestimmung des Chlorgehaltes - Teil 1: Anorganisches Chlor
(ISO 21627-1:2002)
Plastiques - Résines époxydes - Détermination de la teneur en chlore - Partie 1: Chlore
inorganique (ISO 21627-1:2002)
Ta slovenski standard je istoveten z: EN ISO 21627-1:2003
ICS:
83.080.10 Duromeri Thermosetting materials
SIST EN ISO 21627-1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 21627-1:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 21627-1:2004
EUROPEAN STANDARD
EN ISO 21627-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2003
ICS 83.080.10 Supersedes EN ISO 11376:2001
English version
Plastics - Epoxy resins - Determination of chlorine content Part
1: Inorganic chlorine (ISO 21627-1:2002)
Plastiques - Résines époxydes - Détermination de la teneur Kunststoffe - Epoxidharze - Bestimmung des Chlorgehaltes
en chlore - Partie 1: Chlore inorganique (ISO 21627- - Teil 1: Anorganisches Chlor (ISO 21627-1:2002)
1:2002)
This European Standard was approved by CEN on 25 October 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21627-1:2003 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 21627-1:2004
EN ISO 21627-1:2003 (E)
Foreword
The text of ISO 21627-1:2002 has been prepared by Technical Committee ISO/TC 61 "Plastics”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO
21627-1:2003 by Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held
by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2004, and conflicting national standards
shall be withdrawn at the latest by May 2004.
This document supersedes EN ISO 11376:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 21627-1:2002 has been approved by CEN as EN ISO 21627-1:2003 without any
modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 21627-1:2004
EN ISO 21627-1:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 3696 1987 Water for analytical laboratory use - EN ISO 3696 1995
Specification and test methods
3

---------------------- Page: 5 ----------------------

SIST EN ISO 21627-1:2004

---------------------- Page: 6 ----------------------

SIST EN ISO 21627-1:2004
INTERNATIONAL ISO
STANDARD 21627-1
First edition
2002-08-15
Plastics — Epoxy resins — Determination
of chlorine content —
Part 1:
Inorganic chlorine
Plastiques — Résines époxydes — Détermination de la teneur en chlore —
Partie 1: Chlore inorganique

Reference number
ISO 21627-1:2002(E)
© ISO 2002

---------------------- Page: 7 ----------------------

SIST EN ISO 21627-1:2004
ISO 21627-1:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2002 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 21627-1:2004
ISO 21627-1:2002(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Term and definition . 1
4 Principle . 1
5 Reagents . 2
6 Apparatus . 2
7 Procedure . 3
8 Expression of results . 3
9 Precision . 4
10 Test report . 4
Bibliography. 5
©
ISO 2002 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 21627-1:2004
ISO 21627-1:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 21627 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 21627-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 12, Thermosetting materials.
This first edition cancels and replaces ISO 11376:1997 of which it constitutes a technical revision.
ISO 21627 consists of the following parts, under the general title Plastics — Epoxy resins — Determination of
chlorine content:
— Part 1: Inorganic chlorine
— Part 2
...