SIST EN 3386:2012
(Main)Aerospace series - Rings retaining, radial mounting, steel, phosphated
Aerospace series - Rings retaining, radial mounting, steel, phosphated
This European Standard defines the characteristics of radial mounting retaining rings, in steel, phosphated, for aerospace applications.
These retaining rings are used only when EN 3384 cannot be used for installation problems.
The phosphating restricts the use at temperatures not exceeding 200 °C.
Luft- und Raumfahrt - Sicherungsringe, radial montierbar, aus Stahl, phosphatiert
Diese Norm legt die Merkmale von radial montierbaren Sicherungsringen aus Stahl mit Phosphatbeschichtung
zur Anwendung in der Luft- und Raumfahrt fest.
Diese Sicherungsringe werden nur verwendet, wenn EN 3384 aufgrund von Installationsproblemen nicht
angewandt werden kann.
Die Phosphatbeschichtung beschränkt die Verwendung auf Temperaturen von nicht mehr als 200 °C.
Série aérospatiale - Anneaux d’arrêt, à montage radial, en acier, phosphatés
La présente Norme Européenne définit les caractéristiques des anneaux d’arrêt, à montage radial, en acier, phosphatés pour applications aérospatiales.
Ces anneaux d’arrêt sont seulement utilisés lorsque l'EN 3384 ne peut être employée pour des problèmes de montage.
La phosphatation limite l’utilisation à des températures ne dépassant pas 200 °C.
Aeronavtika - Varnostni obroči za radialno pritrditev, jekleni, fosfatirani
Ta standard določa lastnosti jeklenih fosfatiranih varnostnih obročev za radialno pritrditev za uporabo v aeronavtiki. Ti varnostni obroči se uporabljajo samo, če zaradi težav z inštalacijo ni mogoče uporabiti standarda EN 3384. Fosfatiranje omejuje uporabo na temperature, ki ne presegajo 200 °C.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RVIDWLUDQLLuft- und Raumfahrt - Sicherungsringe, radial montierbar, aus Stahl, phosphatiertSérie aérospatiale - Anneaux d’arrêt, à montage radial, en acier, phosphatésAerospace series - Rings retaining, radial mounting, steel, phosphated49.030.50Podložke in drugi blokirni elementiWashers and other locking elementsICS:Ta slovenski standard je istoveten z:EN 3386:2012SIST EN 3386:2012en01-maj-2012SIST EN 3386:2012SLOVENSKI
STANDARD
SIST EN 3386:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3386
March 2012 ICS 49.030.50 English Version
Aerospace series - Rings retaining, radial mounting, steel, phosphated
Série aérospatiale - Anneaux d'arrêt, à montage radial, en acier, phosphatés
Luft- und Raumfahrt - Sicherungsringe, radial montierbar, aus Stahl, phosphatiert This European Standard was approved by CEN on 24 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3386:2012: ESIST EN 3386:2012
EN 3386:2012 (E) 2 Contents Page Foreword . 31 Scope and field of application . 42 Normative references . 43 Required characteristics . 43.1 Configuration — Dimensions — Masses . 43.2 Materials . 43.3 Surface treatment . 44 Designation . 65 Marking. 76 Technical specification . 77 Mounting . 7 SIST EN 3386:2012
EN 3386:2012 (E) 3 Foreword This document (EN 3386:2012) has been prepared b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.