SIST ISO 10129:2020

SLOVENSKI STANDARD
SIST ISO 10129:2020
01-oktober-2020
Drsni ležaji - Preskušanje kovin za ležaje - Odpornost kovine proti korozivnemu
delovanju maziva v kopeli
Plain bearings - Testing of bearing metals - Resistance to corrosion by lubricants under
static conditions
Paliers lisses - Essai des matériaux antifriction - Résistance à la corrosion par des
lubrifiants dans des conditions statiques
Ta slovenski standard je istoveten z: ISO 10129:2017
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 10129:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 10129:2020

---------------------- Page: 2 ----------------------
SIST ISO 10129:2020
INTERNATIONAL ISO
STANDARD 10129
Second edition
2017-03
Plain bearings — Testing of bearing
metals — Resistance to corrosion by
lubricants under static conditions
Paliers lisses — Essai des matériaux antifriction — Résistance à la
corrosion par des lubrifiants dans des conditions statiques
Reference number
ISO 10129:2017(E)
©
ISO 2017

---------------------- Page: 3 ----------------------
SIST ISO 10129:2020
ISO 10129:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 10129:2020
ISO 10129:2017(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Health and safety . 1
5 General principles . 1
6 Lubricants . 2
7 Apparatus . 2
8 Preparation of test samples . 2
9 Test procedure . 3
10 Expression of results . 3
10.1 Mass change . 3
10.2 Changes in dimensions . 3
10.3 Surface changes . 3
10.4 Microstructural changes . 4
10.5 Type and nature of the corrosion products . 4
10.6 Change of lubricant . 4
11 Test report . 4
Bibliography . 5
© ISO 2017 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 10129:2020
ISO 10129:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 2,
Materials and lubricants, their properties, characteristics, test methods and testing conditions.
This second edition cancels and replaces the first edition (ISO 10129:2006), which has been technically
revised.
iv © ISO 2017 – All rights reserved

---------------------- Page: 6 ----------------------
SIST ISO 10129:2020
ISO 10129:2017(E)

Introduction
It is essential that certain properties of bearing materials combined within the tribological system
remain unchanged or change only within a permissible range over a long period of time. It is on account
of these properties that the materials are regarded as being especially suitable for the tribological
system. As to the tribological system “plain bearing”, the compatibility between the bearing materials
and lubricant is of special interest and is dependent on chemical and mechanical actions.
The test established in this document determines the behaviour of plain bearing materials with respect
to corrosion by lubricants (lubricating oils) under static conditions, i.e. without any mechanical action
taking place simultaneously.
In order for such corrosion tests to be evaluated and compared, it is necessary that they be carried out in
accordance with the conditions laid down in this document. Other conditions are to be indicated in detail.
© ISO 2017 – All rights reserved v

---------------------- Page: 7 ----------------------
SIST ISO 10129:2020

---------------------- Page: 8 ----------------------
SIST ISO 10129:2020
INTERNATIONAL STANDARD ISO 10129:2017(E)
Plain bearings — Testing of bearing metals — Resistance to
corrosion by lubricants un
...