kSIST FprEN 14404-5:2022

SLOVENSKI STANDARD
oSIST prEN 14404-5:2019
01-maj-2019
2VHEQDYDURYDOQDRSUHPDâþLWQLNL]DNROHQD]DGHORYNOHþHþHPSRORåDMXGHO
=DKWHYH]DSRGORJH]DNROHQDWLS
Personal protective equipment - Knee protectors for work in the kneeling position – Part
5: Requirements for knee mats (type 3)
Persönliche Schutzausrüstung - Knieschutz für Arbeiten in kniender Haltung - Teil 5:
Anforderungen an Kniematten (Typ 3)
Équipements de protection individuelle - Protection des genoux pour le travail à genoux -
Partie 5 : Exigences relatives aux tapis pour genoux (type 3)
Ta slovenski standard je istoveten z: prEN 14404-5
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
oSIST prEN 14404-5:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 14404-5:2019
oSIST prEN 14404-5:2019
DRAFT
EUROPEAN STANDARD
prEN 14404-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2019
ICS 13.340.50 Will supersede EN 14404:2004+A1:2010
English Version
Personal protective equipment - Knee protectors for work
in the kneeling position - Part 5: Requirements for knee
mats (type 3)
Équipements de protection individuelle - Protection Persönliche Schutzausrüstung - Knieschutz für
des genoux pour le travail à genoux - Partie 5 : Arbeiten in kniender Haltung - Teil 5: Anforderungen
Exigences relatives aux tapis pour genoux (type 3) an Kniematten (Typ 3)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 162.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14404-5:2019 E
worldwide for CEN national Members.

oSIST prEN 14404-5:2019
prEN 14404-5:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Performance levels . 5
5 Requirements . 6
5.1 General requirements for knee mats . 6
5.2 Products for testing . 7
5.3 Orientation of the knee mats . 7
5.4 Specific requirements for knee mats . 7
5.4.1 Size and dimension . 7
5.4.2 Penetration resistance . 8
5.4.3 Force distribution . 8
5.4.4 Peak transmitted force. 8
5.5 Optional requirements - Water resistance . 9
5.6 Ergonomic requirements . 9
6 Marking . 9
6.1 General . 9
6.2 Specific . 9
7 Information to be supplied by the manufacturer . 10
Annex A (informative) Information on the problems of using knee protectors for work in
the kneeling position . 12
A.1 Introduction . 12
A.2 Advice to users . 12
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/425 of the European Parliament and of the
Council of 9 March 2016 on personal protective equipment aimed to be covered. 13
oSIST prEN 14404-5:2019
prEN 14404-5:2019 (E)
European foreword
This document (prEN 14404-5:2019) has been prepared by Technical Committee CEN/TC 162
“Protective clothing including hand and arm protection and life jackets”, the secretariat of which is held
by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 14404:2004+A1:2010.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
This standard “Personal protective equipment - Knee protectors for work in the kneeling position” is
split into 6 parts:
— Part 1: Test methods
— Part 2: Requirements for wearable knee protectors (type 1)
— Part 3: Requirements for the combination of knee pads and garments (type 2)
— Part 4: Requirements for the combination of interoperable knee pads and garments (type 2)
— Part 5: Requirements for knee mats (type 3)
— Part 6: Requirements for kneeling systems (type 4)
oSIST prEN 14404-5:2019
prEN 14404-5:2019 (E)
Introduction
Kneeling is a frequently occurring working position, but one which is problematic from an occupational
health viewpoint. Without knee protectors, workers may suffer immediate injuries from hard surfaces
and small stones and similar objects lying on the surfaces. However, no knee protector can ensure that
workers will not suffer medical complications if they are required to kneel for long periods.
It is important that knee protectors do not compromise venous drainage in the leg while kneeling or
standing up. Therefore, it is important that it is easy for workers to change position and to stand up to
re-establish a normal blood circulation at frequent intervals while wearing knee protectors.
Work in a kneeling position involves the risk of chronic diseases such as prepatellar bursitis and
cartilage injuries caused by continuous pressure on the knees. Knee protection is therefore
recommended for all work in the kneeling position. The protection should distribute forces evenly and
prevent small hard objects on the ground causing injuries. Many workers have pre-existing damage to
their knees, particularly to their cartilages from sports injuries and from previous work. These injuries
will be made worse by further kneeling. Wearing knee protectors cannot correct existing damage, but
should slow down further damaging effects.
Work in a kneeling position may expose the skin of the shins, knees and thighs to toxic and corrosive
materials normally kept off the body while walking and standing by waterproof or water-resistant
footwear. Knee protectors and trousers for use with such wet materials and particularly wet cement,
should take this into account and provide adequate protection, as does footwear.
For working in kneeling position exist 4 types of knee protectors:
— wearable knee protectors (type 1),
— knee pads in combination with garments (type 2),
— knee mats (type 3) and
— kneeling systems (type 4)
This standard describes test methods, specifies requirements for knee protectors and defines
performance levels. Requirements for the marking of knee protectors and the information to be
supplied by the manufacturer are given. Where protection against additional hazards is claimed,
performance requirements from other applicable standards may also be applied.
This standard does not apply to knee protectors that are medical devices or are intended for sports and
motorcycles.
oSIST prEN 14404-5:2019
prEN 14404-5:2019 (E)
1 Scope
This document specifies the requirements for knee mats (type 3) for use by work in kneeling position.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
prEN 14404-1:2019, Knee protectors for work in the kneeling position – Test methods
EN ISO 3758, Textiles - Care labelling code using symbols
EN ISO 13688, Protective clothing - General requirements (ISO 13688)
ISO 7000, Graphical symbols for use on equipment — Registered symbols
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
knee mat (type 3)
device not attached to the body, but put into place as the user moves around
Note 1 to entry: These may be for each knee or both knees together.
3.2
zone of protection
surface of the knee protector that is intended to provide the user with protection of patellar and
infrapatellar areas
4 Performance levels
4 performance levels are defined. The tests for the performance levels are described in 4 of
prEN 14404-1:2019:
— level 0: knee protectors suitable for use on flat floor surfaces and providing no protection against
penetration.
— level 1: knee protectors suitable for use on flat floor surfaces and providing protection against
penetration at a force of at least 100 N
— level 1U: knee protectors suitable for use on even or uneven surfaces providing protection against
penetration at a force of at least 100 N.
— level 2: knee protectors suitable for use on flat or non-flat floor surfaces in severe conditions and
providing protection against penetration at a force of at least 250 N.
oSIST prEN 14404-5:2019
prEN 14404-5:2019 (E)
5 Requirements
Summary of the requirements given in Clause 5.1 – 7 for knee mats (type 3) and the tests applicable
Table 1 — Summary of requirements for knee mats (type 3) and the tests applicable
Level
Clause Clauses describing the
Subject
number tests applicable
0 1 1U 2
5.1 General requirements X X X X Part 1: 5.4.1
Part 1: 5.4.2
5.1 Innocuousness X X X X
EN ISO 13688
Comparison with Clause 5,
5.2 Products for testing X X X X
5.2
Comparison with Clause 5,
5.3.1 Orientation of the knee protector X X X X
5.3.1
5.4.1.1 Size designation X X X X Part 1: 5.4.3
5.4.1.2 Dimensions X X X X Part 1: 5.4.3
Penetration resistance
5.4.2 n.a. X X X Part 1: 5.5
(Performance levels 1, 1U and 2)
5.4.3.1 Force distribution on an even surface X X n.a. n.a. Part 1: 5.6.2.1
Force distribution on an uneven
5.4.3.2 n.a. n.a. X X Part 1: 5.6.2.2
surface
5.4.4 Peak transmitted force X X X X Part 1: 5.7
Optional requirement for water
5.5 X X X X Part 1: 5.9.1
resistance
5.6 Comfort during use X X X X Part 1: 5.11.2.1
6 Marking X X X X Comparison with Clause 4
7 Manufacturer information X X X X Comparison with Clause 5
NOTE n
...