SIST EN ISO 877-2:2012
(Main)Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO 877-2:2009)
Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO 877-2:2009)
ISO 877-2:2009 specifies a method for the direct exposure of plastics to solar radiation and a method for the exposure of plastics to glass-filtered solar radiation (exposure behind window glass). The purpose is to assess property changes produced after specified stages of such exposures.
Kunststoffe - Freibewitterung - Teil 2: Bewitterung und Bestrahlen hinter Fensterglas (ISO 877-2:2009)
Dieser Teil von ISO 877 legt ein Verfahren für die direkte Beanspruchung von Kunststoffen durch die Sonnenstrahlung
(Verfahren A) und ein Verfahren für die Beanspruchung von Kunststoffen hinter Fensterglas
(Verfahren B) fest. Das Ziel ist es, die Eigenschaftsänderungen, die nach bestimmten Stufen derartiger Beanspruchungen
eintreten, zu beurteilen. Eine allgemeine Anleitung, die den Anwendungsbereich von ISO 877
betrifft, ist in ISO 877-1:2009, Abschnitt 1, angegeben.
Plastiques - Méthodes d'exposition au rayonnement solaire - Partie 2: Exposition directe et exposition derrière une vitre en verre (ISO 877-2:2009)
L'ISO 877-2:2009 spécifie une méthode d'exposition directe des plastiques au rayonnement solaire et une méthode d'exposition des plastiques au rayonnement solaire sous filtre de verre (exposition derrière une vitre en verre). L'objectif consiste à évaluer les changements de propriété produits après des phases d'exposition spécifiées.
Polimerni materiali - Metode izpostavitve vremenskim vplivom - 2. del: Vremenski vplivi z dnevno svetlobo, filtrirano skozi steklo (ISO 877-2:2009)
Ta del standarda ISO 877 določa metodo za neposredno izpostavitev polimernih materialov sončnemu sevanju (metoda A) in metodo za izpostavitev polimernih materialov sončnemu sevanju, ki jih filtrira steklo (izpostavitev za okenskim steklom) (metoda B). Namen je oceniti spremembe lastnosti, do katerih pride po določenih stopnjah take izpostavitve. Splošni napotki v zvezi s področjem uporabe standarda ISO 877 so podani v točki 1 standarda ISO 877-1:2009.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 877-2:2012
01-marec-2012
1DGRPHãþD
SIST EN ISO 877:2000
Polimerni materiali - Metode izpostavitve vremenskim vplivom - 2. del: Vremenski
vplivi z dnevno svetlobo, filtrirano skozi steklo (ISO 877-2:2009)
Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and
exposure behind window glass (ISO 877-2:2009)
Kunststoffe - Freibewitterung - Teil 2: Bewitterung und Bestrahlen hinter Fensterglas
(ISO 877-2:2009)
Plastiques - Méthodes d'exposition au rayonnement solaire - Partie 2: Exposition directe
et exposition derrière une vitre en verre (ISO 877-2:2009)
Ta slovenski standard je istoveten z: EN ISO 877-2:2010
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 877-2:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 877-2:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 877-2:2012
EUROPEAN STANDARD
EN ISO 877-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2010
ICS 83.080.01 Supersedes EN ISO 877:1996
English Version
Plastics - Methods of exposure to solar radiation - Part 2: Direct
weathering and exposure behind window glass (ISO 877-
2:2009)
Plastiques - Méthodes d'exposition au rayonnement solaire Kunststoffe - Freibewitterung - Teil 2: Bewitterung und
- Partie 2: Exposition directe et exposition derrière une vitre Bestrahlen hinter Fensterglas (ISO 877-2:2009)
en verre (ISO 877-2:2009)
This European Standard was approved by CEN on 4 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 877-2:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 877-2:2012
EN ISO 877-2:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 877-2:2012
EN ISO 877-2:2010 (E)
Foreword
The text of ISO 877-2:2009 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 877-2:2010 by
Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2011, and conflicting national standards shall be withdrawn at
the latest by June 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 877:1996.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 877-2:2009 has been approved by CEN as a EN ISO 877-2:2010 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 877-2:2012
---------------------- Page: 6 ----------------------
SIST EN ISO 877-2:2012
INTERNATIONAL ISO
STANDARD 877-2
First edition
2009-06-01
Plastics — Methods of exposure to solar
radiation —
Part 2:
Direct weathering and exposure behind
window glass
Plastiques — Méthodes d'exposition au rayonnement solaire —
Partie 2: Exposition directe et exposition derrière une vitre en verre
Reference number
ISO 877-2:2009(E)
©
ISO 2009
---------------------- Page: 7 ----------------------
SIST EN ISO 877-2:2012
ISO 877-2:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 877-2:2012
ISO 877-2:2009(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Principle. 1
4 Apparatus . 1
5 Test specimens . 3
6 Conditions of exposure of the test specimens. 4
7 Exposure stages . 4
8 Procedure . 5
9 Expression of results . 6
10 Test report . 6
© ISO 2009 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 877-2:2012
ISO 877-2:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 877-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 6, Ageing, chemical
and environmental resistance.
Together with the other parts (see below), it cancels and replaces ISO 877:1994, which has been technically
revised.
ISO 877 consists of the following parts, under the general title Plastics — Methods of exposure to solar
radiation:
⎯ Part 1: General guidance
⎯ Part 2: Direct weathering and exposure behind window glass
⎯ Part 3: Intensified weathering using concentrated solar radiation
iv © ISO 2009 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 877-2:2012
INTERNATIONAL STANDARD ISO 877-2:2009(E)
Plastics — Methods of exposure to solar radiation —
Part 2:
Direct weathering and exposure behind window glass
1 Scope
This part of ISO 877 specifies a method for the direct exposure of plastics to solar radiation (method A) and a
method for the exposure of plastics to glass-filtered solar radiation (exposure behind window glass)
(method B). The purpose is to assess property changes produced after specified stages of such exposures.
General guidance concerning the scope of ISO 877 is given in ISO 877-1:2009, Clause 1.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 877-1: 2009, Plastics — Methods of exposure to solar radiation — Part 1: General guidance
ISO 4582, Plastics — Determination of changes in colour and variations in properties after exposure to
daylight under gl
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Polimerni materiali - Metode izpostave vremenskim vplivom - 2. del: Vremenski vplivi z dnevno svetlobo, filtrirano skozi steklo (ISO 877-2:2009)Kunststoffe - Freibewitterung - Teil 2: Bewitterung und Bestrahlen hinter Fensterglas (ISO 877-2:2009)Plastiques - Méthodes d'exposition au rayonnement solaire - Partie 2: Exposition directe et exposition derrière une vitre en verre (ISO 877-2:2009)Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO 877-2:2009)83.080.01Polimerni materiali na splošnoPlastics in generalICS:Ta slovenski standard je istoveten z:FprEN ISO 877-2kSIST FprEN ISO 877-2:2010en,fr,de01-september-2010kSIST FprEN ISO 877-2:2010SLOVENSKI
STANDARD
kSIST FprEN ISO 877-2:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 877-2
June 2010 ICS 83.080.01 Will supersede EN ISO 877:1996English Version
Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO 877-2:2009)
Plastiques - Méthodes d'exposition au rayonnement solaire - Partie 2: Exposition directe et exposition derrière une vitre en verre (ISO 877-2:2009)
Kunststoffe - Freibewitterung - Teil 2: Bewitterung und Bestrahlen hinter Fensterglas (ISO 877-2:2009) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 877-2:2010: EkSIST FprEN ISO 877-2:2010
FprEN ISO 877-2:2010 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 877-2:2010
FprEN ISO 877-2:2010 (E) 3 Foreword The text of ISO 877-2:2009 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 877-2:2010 by Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN ISO 877:1996. Endorsement notice The text of ISO 877-2:2009 has been approved by CEN as a FprEN ISO 877-2:2010 without any modification.
kSIST FprEN ISO 877-2:2010
kSIST FprEN ISO 877-2:2010
Reference numberISO 877-2:2009(E)© ISO 2009
INTERNATIONAL STANDARD ISO877-2First edition2009-06-01Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure behind window glass Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 2: Exposition directe et exposition derrière une vitre en verre
kSIST FprEN ISO 877-2:2010
ISO 877-2:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2009 – All rights reserved
kSIST FprEN ISO 877-2:2010
ISO 877-2:2009(E) © ISO 2009 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Principle.1 4 Apparatus.1 5 Test specimens.3 6 Conditions of exposure of the test specimens.4 7 Exposure stages.4 8 Procedure.5 9 Expression of results.6 10 Test report.6
kSIST FprEN ISO 877-2:2010
ISO 877-2:2009(E) iv © ISO 2009 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 877-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 6, Ageing, chemical and environmental resistance. Together with the other parts (see below), it cancels and replaces ISO 877:1994, which has been technically revised. ISO 877 consists of the following parts, under the general title Plastics — Methods of exposure to solar radiation: ⎯ Part 1: General guidance ⎯ Part 2: Direct weathering and exposure behind window glass ⎯ Part 3: Intensified weathering using concentrated solar radiation
kSIST FprEN ISO 877-2:2010
INTERNATIONAL STANDARD ISO 877-2:2009(E) © ISO 2009 – All rights reserved 1Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure behind window glass 1 Scope This part of ISO 877 specifies a method for the direct exposure of plastics to solar radiation (method A) and a method for the exposure of plastics to glass-filtered solar radiation (exposure behind window glass) (method B). The purpose is to assess property changes produced after specified stages of such exposures. General guidance concerning the scope of ISO 877 is given in ISO 877-1:2009, Clause 1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 877-1: 2009, Plastics — Methods of exposure to solar radiation — Part 1: General guidance ISO 4582, Plastics — Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources ASTM G 24, Standard Practice for Conducting Exposures to Daylight Filtered Through Glass 3 Principle General guidance is given in ISO 877-1:2009, Clause 4. 4 Apparatus 4.1 General requirements Refer to ISO 877-1:2009, Subclause 5.1, for general requirements. When installed, the racks employed in test methods A and B shall be capable of providing the desired angle of inclination (see 6.1) and shall be such that no portion of an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.