SIST EN 14296:2005

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sanitary appliances - Communal washing troughsSanitarna oprema – Skupinska umivalna koritaAppareils sanitaires - Lavabos collectifsSanitärausstattungsgegenstände - ReihenwaschanlagenTa slovenski standard je istoveten z:EN 14296:2005SIST EN 14296:2005de91.140.70ICS:SLOVENSKI
STANDARDSIST EN 14296:200501-september-2005







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14296May 2005ICS 91.140.70English versionSanitary appliances - Communal washing troughsAppareils sanitaires - Lavabos collectifsSanitärausstattungsgegenstände - ReihenwaschanlagenThis European Standard was approved by CEN on 25 March 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14296:2005: E



EN 14296:2005 (E) 2 Contents page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Requirements.4 4.1 General.4 4.2 Cleanability.4 4.3 Load resistance.5 4.4 Durability.5 5 Test methods.5 5.1 Cleanability.5 5.2 Determination of load resistance.5 6 Marking and product designation.11 7 Evaluation of conformity.11 7.1 General.11 7.2 Initial type testing.12 7.3 Factory production control (FPC).12 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Directive.13 Bibliography.17



EN 14296:2005 (E) 3 Foreword This document (EN 14296:2005) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2005, and conflicting national standards shall be withdrawn at the latest by February 2007. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 89/106. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.



EN 14296:2005 (E) 4 1 Scope This European Standard specifies requirements for the cleanability, load resistance and durability of communal washing troughs used for domestic purposes. NOTE For the purposes of this European Standard the term "domestic purposes" includes use in factory changing-rooms, sportsclubs, accommodation for students, hospitals and similar buildings, except when special medical provisions are required. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 695, Kitchen sinks — Connecting dimensions 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 communal washing trough single bowl sanitary appliance at which more than one person can wash at the same time, designed to be installed with (a) permanently open waste fitting(s) capable of accepting the flow from more than one tap. Communal washing troughs can be installed standing alone (free standing (pedestal)) or wall mounted 3.2 cleanability characteristics which allow surfaces intended to come into contact with water to be visibly smooth, non-absorbent and free from unacceptable internal corners, such they can be kept visibly free from dirt and/or stains when subject to a regular maintenance routine, which may include, when appropriate, the specific instructions for use and care as specified by the manufacturer 4 Requirements 4.1 General The manufacturer shall supply instructions on installation, use and care. The waste outlet hole shall comply with the dimensions as specified in EN 695, unless the manufacturer provides the waste fitting. with the washing trough. 4.2 Cleanability When tested as described in 5.1, communal washing troughs shall have smooth and readily cleansed non-absorbent functional surfaces which are free from acute internal corners, i.e., surfaces intended to or likely to come into contact with water during use. Experience has shown that communal washing troughs manufactured from plastics, enamelled steel/cast iron, stainless steel, glazed ceramics, glass and anodised aluminium, designed and constructed without acute internal corners, satisfy these requirements.



EN 14296:2005 (E) 5 4.3 Load resistance Communal washing troughs shall not crack, collapse or show permanent distortion which prevents water from draining through the waste hole when tested as specified in 5.2.2 and 5.2.4. Communal washing troughs shall not crack, or collapse when tested as specified in 5.2.3. 4.4 Durability Communal washing troughs shall be manufactured from materials that will satisfy the requirements of 4.2 and 4.3. 5 Test methods 5.1 Cleanability Visually examine the functional surface of the communal washing trough using a suitable light source. Record the material of construction and any failure to comply with the requirements of 4.2. Imperfections that do not affect the functionality of the surface shall not constitute a failure. 5.2 Determination of load resistance 5.2.1 General Install the communal washing trough to be tested according to the manufacturer's installation instructions. 5.2.2 Load evenly distributed on the rim Apply an evenly distributed load of 250,50+kg every 50 cm on the rim, as shown in Figures 1a, 1b, 1c and 1d. Reinforced cloth bags filled with lead shot, iron shot or sand shall be used. The load shall remain in position for a minimum period of 1 h.
Key 1 One bag of 250,50+kg or two bags of 12,50,250+kg Figure 1a — Installation for load test - Test on the rim - Wall mounted trough, viewed from the side



EN 14296:2005 (E) 6
Key 1 One bag of 250,50+kg or two bags of 12,50,250+kg Figure 1b — Installation for load test - Test on the rim - Wall mounted trough, viewed from above
Key 1 One bag of 250,50+kg or two bags of 12,50,250+kg Figure 1c — Installation for load test - Test on the rim - Free standing trough, viewed from the side



EN 14296:2005 (E) 7
Key 1 One bag of 250,50+kg or two bags of 12,50,250+kg Figure 1d — Installation for load test - Test on the rim - Free standing trough, viewed from above Note any crack, collapse or permanent distortion preventing water from draining trough the waste hole. 5.2.3 Localised load on the rim Apply a load of 751,50+kg in the middle of the rim, as shown in Figures 2a, 2b, 2c and 2d. Reinforced cloth bags filled with lead shot, iron shot or sand shall be used. The load shall remain in position for a minimum period of 1 h.
Key 1 Three bags of 250,50+kg or six bags of 12,50,250+kg Figure 2a — Installation for load test - Test on the rim - Wall mounted trough, viewed from the side



EN 14296:2005 (E) 8
Key 1 Three bags of 250,50+kg or six bags of 12,50,250+kg Figure 2b — Installation for load test - Test on the rim - Wall mounted trough, viewed from above
Key 1 Three bags of 250,50+kg or six bags of 12,50,250+kg Figure 2c — Installation for load test - Test on the rim - Free standing trough, viewed from the side



EN 14296:2005 (E) 9
Key 1 Three bags of 250,50+kg or six bags of 12,50,250+kg Figure 2d — Installation for load test - Test on the rim - Free standing trough, viewed from above Note any crack, or collapse of the trough. 5.2.4 Test on the bottom Apply an evenly distributed load of 250,50+kg every 50 cm on the bottom, as shown in Figures 3a, 3b, 3c and 3d with a minimum total loading of 75 kg. Rei
...