SIST EN 12390-1:2021
(Main)Testing hardened concrete - Part 1: Shape, dimensions and other requirements for specimens and moulds
Testing hardened concrete - Part 1: Shape, dimensions and other requirements for specimens and moulds
This document specifies the shape, dimensions and tolerances of cast concrete test specimens in the form of cubes, cylinders and prisms, and of the moulds required to produce them.
NOTE The tolerances specified in this document are based on the needs of strength testing, but they can be applicable to tests for other properties.
Prüfung von Festbeton - Teil 1: Form, Maße und andere Anforderungen für Probekörper und Formen
Dieses Dokument legt die Form, Maße und zulässigen Abweichungen von Probekörpern aus Beton in Form von Würfeln, Zylindern und Prismen und die für ihre Herstellung erforderlichen Formen fest.
ANMERKUNG Die in diesem Dokument festgelegten zulässigen Abweichungen basieren auf den Erfordernissen von Festigkeitsprüfungen, sie können jedoch auch für die Prüfungen anderer Eigenschaften angewendet werden.
Essais pour béton durci - Partie 1 : Forme, dimensions et autres exigences aux éprouvettes et aux moules
Le présent document spécifie la forme, les dimensions et tolérances des éprouvettes de béton moulé ayant la forme de cubes, cylindres et prismes ainsi que des moules nécessaires à leur confection.
NOTE Les tolérances spécifiées dans le présent document ont été établies en fonction des besoins des essais de résistance, mais peuvent aussi convenir à des essais de détermination d’autres caractéristiques.
Preskušanje strjenega betona - 1. del: Oblika, mere in druge zahteve za vzorce in kalupe
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12390-1:2021
01-september-2021
Nadomešča:
SIST EN 12390-1:2013
Preskušanje strjenega betona - 1. del: Oblika, mere in druge zahteve za vzorce in
kalupe
Testing hardened concrete - Part 1: Shape, dimensions and other requirements for
specimens and moulds
Prüfung von Festbeton - Teil 1: Form, Maße und andere Anforderungen für Probekörper
und Formen
Essais pour béton durci - Partie 1 : Forme, dimensions et autres exigences aux
éprouvettes et aux moules
Ta slovenski standard je istoveten z: EN 12390-1:2021
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
SIST EN 12390-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12390-1:2021
---------------------- Page: 2 ----------------------
SIST EN 12390-1:2021
EN 12390-1
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2021
EUROPÄISCHE NORM
ICS 91.100.30 Supersedes EN 12390-1:2012
English Version
Testing hardened concrete - Part 1: Shape, dimensions and
other requirements for specimens and moulds
Essais pour béton durci - Partie 1 : Forme, dimensions Prüfung von Festbeton - Teil 1: Form, Maße und andere
et autres exigences aux éprouvettes et aux moules Anforderungen für Probekörper und Formen
This European Standard was approved by CEN on 7 June 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12390-1:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12390-1:2021
EN 12390-1:2021 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Shape, dimensions and tolerances of specimens . 5
4.1 General . 5
4.2 Cubes . 6
4.2.1 Nominal sizes . 6
4.2.2 Designated sizes . 6
4.2.3 Tolerances . 6
4.3 Cylinders. 6
4.3.1 Nominal sizes . 6
4.3.2 Designated sizes .
...
SLOVENSKI STANDARD
oSIST prEN 12390-1:2019
01-november-2019
Preskušanje strjenega betona - 1. del: Oblika, mere in druge zahteve za vzorce in
kalupe
Testing hardened concrete - Part 1: Shape, dimensions and other requirements for
specimens and moulds
Prüfung von Festbeton - Teil 1: Form, Maße und andere Anforderungen für Probekörper
und Formen
Essais pour béton durci - Partie 1 : Forme, dimensions et autres exigences relatives aux
éprouvettes et aux moules
Ta slovenski standard je istoveten z: prEN 12390-1
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
oSIST prEN 12390-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12390-1:2019
---------------------- Page: 2 ----------------------
oSIST prEN 12390-1:2019
DRAFT
EUROPEAN STANDARD
prEN 12390-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2019
ICS 91.100.30 Will supersede EN 12390-1:2012
English Version
Testing hardened concrete - Part 1: Shape, dimensions and
other requirements for specimens and moulds
Essais pour béton durci - Partie 1 : Forme, dimensions Prüfung von Festbeton - Teil 1: Form, Maße und andere
et autres exigences relatives aux éprouvettes et aux Anforderungen für Probekörper und Formen
moules
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 104.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12390-1:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12390-1:2019
prEN 12390-1:2019 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Shape, dimensions and tolerances of specimens . 5
4.1 General . 5
4.2 Cubes . 6
4.2.1 Nominal sizes . 6
4.2.2 Designated sizes . 6
4.2.3 Tolerances . 6
4.3 Cylinders.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.