iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12373-15:2002

(Main)

Aluminium and aluminium alloys - Anodizing - Part 15: Assessment of resistance of anodic oxidation coatings to cracking by deformation

Aluminium and aluminium alloys - Anodizing - Part 15: Assessment of resistance of anodic oxidation coatings to cracking by deformation

This part of this European Standard specifies an empirical method for assessing the resistance of anodic oxidation coatings to cracking by deformation. The method is applicable particularly to sheet material with anodic oxidation coatings of thickness less than 5 micrometres, and is useful for development purposes.

Aluminium und Aluminiumlegierungen - Anodisieren - Teil 15: Prüfung der Beständigkeit von anodisch erzeugten Oxidschichten gegen Rißbildung bei Verformung

Dieser Teil dieser Europäischen Norm legt ein empirisches Verfahren zur Prüfung der Beständigigkeit anodisch erzeugter Oxidschichten gegen Rißbildung durch Verformung fest. Das Verfahren ist besonders bei Blech mit dünnen erzeugten Oxidschichten kleiner 5 microm anwendbar und für Entwicklungßwecke von Nutzen.

Aluminium et alliages d'aluminium - Anodisation - Partie 15: Evaluation de la résistance des couches anodiques a la formation de criques par déformation

La présente partie de cette norme européenne spécifie une méthode de contrôle empirique permettant d'évaluer la résistance des couches anodiques a la formation de criques par déformations. Cette méthode s'applique particulierement aux tôles recouvertes d'une mince couche anodique d'épaisseur inférieure a 5 micrometres et trouve son application en particulier en développement.

Aluminij in aluminijeve zlitine - Anodizacija - 15. del: Ocenjevanje odpornosti anodizirane plasti proti razpokanju zaradi deformacije

General Information

Status
Withdrawn
Publication Date
31-Jan-2002
Withdrawal Date
22-Nov-2011
ICS
25.220.20 - Surface treatment
77.120.10 - Aluminium and aluminium alloys
Technical Committee
INEK - Nonferrous metals
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
21-Nov-2011
Due Date
14-Dec-2011
Completion Date
23-Nov-2011
Ref Project
EN 12373-15:2000 - Aluminium and aluminium alloys - Anodizing - Part 15: Assessment of resistance of anodic oxidation coatings to cracking by deformation

Relations

Replaced By
SIST EN ISO 3211:2012 - Anodizing of aluminium and its alloys - Assessment of resistance of anodic oxidation coatings to cracking by deformation (ISO 3211:2010)
Effective Date
01-Jan-2012

Buy Standard

EN 12373-15:2002EN 12373-15:2002
PreviousNext
Standard
EN 12373-15:2002
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminij in aluminijeve zlitine - Anodizacija - 15. del: Ocenjevanje odpornosti anodizirane plasti proti razpokanju zaradi deformacijeAluminium und Aluminiumlegierungen - Anodisieren - Teil 15: Prüfung der Beständigkeit von anodisch erzeugten Oxidschichten gegen Rißbildung bei VerformungAluminium et alliages d'aluminium - Anodisation - Partie 15: Evaluation de la résistance des couches anodiques a la formation de criques par déformationAluminium and aluminium alloys - Anodizing
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 7668:2021(Main)
Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20°, 45°, 60° or 85° (ISO 7668:2021)
EN ISO 7668:2021

This document specifies methods for the measurement of specular reflectance and specular gloss of
flat samples of anodized aluminium using geometries of 20° (Method A), 45° (Method B), 60° (Method
C) and 85° (Method D) and of specular reflectance by an additional 45° method (Method E) employing a
narrow acceptance angle.
The methods described are intended mainly for use with clear anodized surfaces. They can be used
with colour-anodized aluminium, but only with similar colours.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 18771:2020(Main)
Anodizing of aluminium and its alloys - Method to test the surface abrasion resistance using glass-coated abrasive paper (ISO 18771:2019)
EN ISO 18771:2020

This document specifies a method for the determination of the surface abrasion resistance of anodic oxidation coatings produced by sulfuric acid anodizing of aluminium and its alloys. It is mainly intended for the evaluation of external architectural coatings. It is a production control method that relies to a large extent on operator experience and instruction.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 2106:2020(Main)
Anodizing of aluminium and its alloys - Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method (ISO 2106:2019)
EN ISO 2106:2020

This document specifies a gravimetric method for determining the mass per unit area(surface density) of anodic oxidation coatings on aluminium and its alloys. Themethod is applicable to all oxidation coatings formed by anodizing aluminium andits alloys, either cast or wrought, and is suitable for most aluminium alloys,except those in which the mass fraction of copper is greater than 6 %.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 2376:2019(Main)
Anodizing of aluminium and its alloys - Determination of breakdown voltage and withstand voltage (ISO 2376:2019)
EN ISO 2376:2019

This document specifies test methods for the determination of the breakdown voltage and withstand
voltage of anodic oxidation coatings on aluminium and its alloys, on flat or near-flat surfaces and on
round wire. The methods are applicable to anodic oxidation coatings used primarily as electrical
insulators.
The methods are not applicable to coatings in the vicinity of cut edges, the edges of holes, or sharp
changes of angle on, for example, extruded shapes.
NOTE 1 Breakdown voltage and withstand voltage are affected by relative humidity.
NOTE 2 The methods described do not give satisfactory results for unsealed coatings because they are
affected by the humidity in particular.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 8994:2019(Main)
Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Grid method (ISO 8994:2018)
EN ISO 8994:2018

This document specifies a grid rating system that provides a means of defining levels of performance of
anodic oxidation coatings on aluminium and its alloys that have been subjected to corrosion tests.
This rating system is applicable to pitting corrosion resulting from
— accelerated tests,
— exposure to corrosive environments, and
— practical service tests.
This document takes into account only pitting corrosion of the basis metal resulting from penetration
of the protective anodic oxidation coating.
NOTE 1 ISO 8993[1] describes a similar rating system based on defined chart scales.
NOTE 2 The grid rating system is frequently used for rating the results of short-term corrosion tests for
relatively thin anodic oxidation coating, such as those used in the automotive industry.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3211:2019(Main)
Anodizing of aluminium and its alloys - Assessment of resistance of anodic oxidation coatings to cracking by deformation (ISO 3211:2018)
EN ISO 3211:2018

This document specifies an empirical method for assessing the resistance of anodic oxidation coatings
to cracking by deformation.
The method is applicable particularly to sheet material with anodic oxidation coatings of thickness less
than 5 μm, and is useful for development purposes.
NOTE If the test specimen is thick, more than 5 μm of coating can be measured (see Clause 9).

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 2085:2018(Main)
Anodizing of aluminium and its alloys - Check for continuity of thin anodic oxidation coatings - Copper sulfate test (ISO 2085:2018)
EN ISO 2085:2018

This document specifies a method for checking the continuity of thin anodic oxidation coatings on
aluminium and its alloys by a copper sulfate contact test.
The use of this method is limited to anodic oxidation coatings of thickness less than 5 μm or coatings
that have been deformed, which includes those produced by coil anodizing techniques.
NOTE The method described enables a rapid check to be made for the continuity of a thin coating of
aluminium oxidation on aluminium and its alloys. In cases of doubt regarding a visible fault on the surface of
a coating, the use of this method makes it possible to verify whether the fault corresponds to a local gap in the
coating that exposes bare metal.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 8251:2018(Main)
Anodizing of aluminium and its alloys - Measurement of abrasion resistance of anodic oxidation coatings (ISO 8251:2018)
EN ISO 8251:2018

This document specifies the following tests:
a) abrasive-wheel-wear test, determining the abrasion resistance of anodic oxidation coatings with
abrasive wheel on flat specimens of aluminium and its alloys;
b) abrasive jet test, determining the comparative abrasion resistance of anodic oxidation coatings
with jet of abrasive particles on anodic oxidation coatings of aluminium and its alloys;
c) falling sand abrasion test, determining the abrasion resistance of anodic oxidation coatings with
falling sand on thin anodic oxidation coatings of aluminium and its alloys.
The use of abrasive-wheel-wear test and abrasive jet test for coatings produced by hard anodizing is
described in ISO 10074.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 6581:2018(Main)
Anodizing of aluminium and its alloys - Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings (ISO 6581:2018)
EN ISO 6581:2018

This document specifies a comparative method for the determination of the fastness of coloured anodic
oxidation coatings to ultraviolet (UV) light and heat.
The method is not suitable for testing coloured anodic oxidation coatings that are heat sensitive.
NOTE Dark-coloured test specimens will normally reach the highest temperatures.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 8993:2018(Main)
Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Chart method (ISO 8993:2018)
EN ISO 8993:2018

This document specifies a chart rating system based on standard charts that provides a means of
defining levels of performance of anodic oxidation coatings on aluminium and its alloys that have been
subjected to corrosion tests.
This rating system is applicable to pitting corrosion resulting from
— accelerated tests,
— exposure to corrosive environments, and
— practical service tests.
This document takes into account only pitting corrosion resulting from penetration of the protective
anodic oxidation coating.
NOTE ISO 8994[1] describes a similar rating system based on defined grids.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day