SIST EN 14309:2010+A1:2013
(Main)Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification
Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification
This European Standard specifies the requirements for factory made products of expanded polystyrene which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 180 °C to + 80 °C. Modified expanded polystyrene polymers with a higher temperature resistance are also covered by this standard. NOTE Below an operating temperature of - 50 °C, special tests regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturers’ advice should be heeded in all cases. The products are manufactured in the form of faced or unfaced boards, rolls, lags, pipe sections or other prefabricated ware. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This standard does not specify the required level or class of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,060 W/(m•K) at 10 °C are not covered by this standard. This standard does not cover products for in situ insulation (for loose fill or poured insulation) or products for the insulation of the building structure.
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation
Diese Europäische Norm legt die Anforderungen für werkmäßig hergestellte Produkte aus expandiertem Polystyrol fest, die als Wärmedämmstoffe für die technische Gebäudeausrüstung und betriebstechnische Anlagen in der Industrie im Temperaturbereich von etwa 180 °C bis +80 °C benutzt werden. Diese Europäische Norm gilt auch für expandierte modifizierte Polystyrol-Polymere mit einem höheren Temperaturwiderstand.
ANMERKUNG Unterhalb einer Betriebstemperatur von 50 °C sind besondere Prüfungen bezüglich der Eignung der Produkte für den beabsichtigten Anwendungsfall ratsam (z. B. Sauerstoffverflüssigung). In jedem Fall sollten die Empfehlungen des Herstellers beachtet werden.
Die Produkte werden mit oder ohne Kaschierung in der Form von Platten, Rollen, Segmenten, Rohrschalen oder anderen vorgefertigten Produkten hergestellt.
Diese Europäische Norm beschreibt die Stoffeigenschaften und enthält die Prüfverfahren und Festlegungen für die Konformitätsbewertung, die Kennzeichnung und die Etikettierung.
In dieser Norm beschriebene Produkte werden auch in vorgefertigten Wärmedämmsystemen und Mehr¬schicht-Verbundplatten angewendet; die Eigenschaften von Systemen, in die diese Produkte integriert sind, werden nicht behandelt.
Diese Norm legt keine Leistungsstufen oder Klassen für eine vorgegebene Eigenschaft fest, die ein Produkt erreichen muss, um für einen bestimmten Anwendungsfall tauglich zu sein. Für bestimmte Anwendungen benötigte Klassen und Stufen können Regelwerken oder Ausschreibungen entnommen werden.
Diese Norm gilt nicht für Produkte, deren Nennwert der Wärmeleitfähigkeit größer ist als 0,060 W/(m K) bei 10 °C.
Diese Norm gilt nicht für Produkte für an der Verwendungsstelle hergestellte Wärmedämmung (eingeblasen oder geschüttet) oder Produkte, die zur Dämmung von Gebäudehüllen bestimmt sind.
Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en polystyrène expansé (PSE) - Spécification
La présente Norme européenne spécifie les exigences relatives aux produits manufacturés en polystyrène expansé utilisés pour l'isolation thermique de l’équipement du bâtiment et des installations industrielles dont la température de service se situe entre – 180 °C et + 80 °C environ. Des polymères modifiés de polystyrène expansé ayant une résistance accrue à la température sont également couverts par la présente norme.
NOTE Pour une température de service inférieure à – 50 °C, des essais particuliers sont recommandés pour s'assurer de l'aptitude à l'emploi du produit dans l'application visée (par exemple, liquéfaction de l'oxygène). Il convient de se référer systématiquement aux conseils du fabricant.
Les produits sont fabriqués sous la forme de panneaux avec ou sans parements, de rouleaux, de segments, de coquilles et autres pièces préfabriquées.
La présente norme décrit les caractéristiques des produits et comporte des modes opératoires d'essai, d'évaluation de conformité, de marquage et d’étiquetage.
Les produits couverts par la présente norme sont également utilisés dans des systèmes préfabriqués d'isolation thermique et dans des panneaux composites ; les performances des systèmes incorporant ces produits ne sont pas traitées.
La présente norme ne spécifie pas le niveau ou la classe requis pour une propriété donnée que doit posséder un produit pour démontrer son aptitude à une application particulière. Les classes ou niveaux requis pour une application particulière peuvent être trouvés dans les réglementations et les appels d'offres.
Les produits dont la conductivité thermique déclarée supérieure à 0,060 W/(m.K) à 10 °C ne sont pas couverts par la présente norme.
La présente norme ne couvre pas les produits pour isolation in situ (en vrac ou par déversement) ni ceux destinés à l’isolation de la structure du bâtiment.
Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz ekspandiranega polistirena (EPS) - Specifikacija
Ta evropski standard določa zahteve za proizvode iz ekspandiranega polistirena, ki se uporabljajo za toplotno izolacijo opreme stavb in industrijskih inštalacij z razponom delovne temperature približno od –180 °C do 80 °C. Modificirani polimeri ekspandiranega polistirena z višjo temperaturno odpornostjo so prav tako zajeti v tem standardu. OPOMBA Pod delovno temperaturo –50 °C se priporočajo posebni preskusi glede primernosti proizvoda za nameravano vrsto uporabe (npr. utekočinjenje kisika). V vseh primerih je treba upoštevati napotke proizvajalca. Proizvodi so izdelani v obliki prevlečenih ali neprevlečenih plošč, kolutov, oblog, vodovodnih odsekov ali drugih predizdelanih oblik. Ta standard opisuje lastnosti proizvodov ter zajema postopke za preskušanje, vrednotenje skladnosti, označevanje in etiketiranje. Proizvodi iz tega standarda se uporabljajo tudi v predizdelanih sistemih toplotne izolacije in vezanih ploščah; lastnosti sistemov iz teh proizvodov niso opisane. Ta standard ne določa zahtevane ravni ali razreda določene lastnosti, ki jo mora proizvod doseči, da se dokaže njegova primernost namenu za posamezno vrsto uporabe. Zahtevani razredi in ravni za posamezno uporabo so določeni v uredbah in javnih razpisih. Proizvodi z deklarirano toplotno prevodnostjo, višjo od 0,060 W/mK pri 10 °C, v tem standardu niso zajeti. Ta standard ne zajema proizvodov za izolacijo na kraju samem (za izolacijo s prostim polnilom ali vlivano izolacijo) ali proizvodov za izolacijo stavbne strukture.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz ekspandiranega polistirena (EPS) - SpecifikacijaWärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - SpezifikationProduits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en polystyrène expansé (PSE) - SpécificationThermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 14309:2009+A1:2013SIST EN 14309:2010+A1:2013en,fr,de01-maj-2013SIST EN 14309:2010+A1:2013SLOVENSKI
STANDARD
SIST EN 14309:2010+A1:2013
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14309:2009+A1
January 2013 ICS 91.100.60 Supersedes EN 14309:2009English Version
Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification
Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en polystyrène expansé (PSE) - Spécification
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation This European Standard was approved by CEN on 29 September 2009 and includes Amendment 1 approved by CEN on 11 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14309:2009+A1:2013: ESIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 2 Contents Page Foreword .4 1 Scope .6 2 Normative references .6 3 Terms, definitions, symbols, units and abbreviated terms .8 4 Requirements . 11 5 Test methods . 20 6 Designation code . 24 7 Evaluation of Conformity . 25 8 Marking and labelling . 26 Annex A (normative)
Factory production control . 27 Annex B (normative)
Product classification . 34 Annex C (normative)
Determination of minimum service temperature . 35 Annex D (informative)
Additional properties . 39 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Directive. 42 Bibliography . 50
Figures Figure A.1 — Relationship between compressive stress at 10 % deformation and apparent density for indirect testing; 1 – α = 90; n = 495 . 31 Figure A.2 — Relationship between declared thermal conductivity (at 50 mm reference thickness and 10 °C mean temperature) and apparent density for indirect testing; 1 – α = 90; n = 3 873 . 32 Figure ZA.1 — Example of CE marking information . 49
Tables Table 1 — Dimensional tolerances . 12 Table 2 — Classes of dimensional stability under normal laboratory conditions . 13 Table 3 — Levels of dimensional stability under specified temperature and humidity conditions . 15 Table 4 — Levels for compressive stress at 10 % deformation . 15 Table 5 — Levels for tensile strength perpendicular to faces . 16 Table 6 — Levels of bending strength . 16 Table 7 — Levels for long time water absorption by total immersion . 17 Table 8 — Levels for long time water absorption by diffusion . 18 Table 9 — Levels for dynamic stiffness . 19 Table 10 — Classes for thickness tolerances . 19 SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 3 Table 11 — Levels for compressibility . 20 Table 12 — Test methods, test specimens, conditions . 22 Table A.1 — Minimum product testing frequencies . 27 Table A.2 — Minimum product testing frequencies for the reaction to fire characteristics . 29 Table A.3 — Thickness effect parameter, L, for the determination of the declared
thermal conductivity, λD
............................................................................................................................................................... 33 Table
B.1 — Classification of EPS products . 34 Table B.2 — Classification of load bearing EPS products with acoustical properties . 34 Table D.1 — Correlation between bending strength and shear strength . 39 Table D.2 — Tabulated values of water vapour diffusion resistance index and water vapour permeability . 40 Table D.3 — Test methods . 41 Table ZA.1 — Relevant clauses . 43 Table ZA.2 — System(s) of attestation of conformity. 44 Table ZA.3 — Assignment of evaluation of conformity tasks for products under system 1 . 45 Table ZA.4 — Assignment of evaluation of conformity tasks for products under system 3 or system 3 combined with system 4 for reaction to fire . 46
SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 4 Foreword This document (EN 14309:2009+A1:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2013, and conflicting national standards shall be withdrawn at the latest by July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14309:2009. This document includes Amendment 1 approved by CEN on 2012-11-11. The start and finish of text introduced or altered by amendment is indicated in the text by tags !". This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 89/106/EEC. For relationship with EU Directive 89/106/EEC, see informative Annex ZA, which is an integral part of this document. Locally responsible authorities and contracting entities, who are bound by EU Directives to specify their requirements using European harmonized product standards, are allowed to demand additional properties outside the provisions of this standard if this is technically necessary because of prevailing operational conditions of the building equipment or the industrial installation projected or because of safety regulations. This European Standard contains five Annexes: Annex A (normative), Factory production control Annex B (normative), Product classification
Annex C (normative), Determination of minimum service temperature Annex D (informative), Additional properties Annex ZA (informative), Clauses of this European Standard addressing the provisions of the EU Construction Products Directive This document includes a bibliography. This European Standard is one of a series of standards for insulation products used in building equipment and industrial installations, but this standard can be used in other areas, where appropriate. In pursuance of Resolution BT 20/1993 revised, CEN/TC 88 have proposed defining the standards listed below as a European package of standards, setting 21 months after availability as the date of withdrawal (dow) of national standards which conflict with the European Standards of this package. The package of standards comprises the following group of interrelated standards for the specifications of factory made thermal insulation products, all of which come within the scope of CEN/TC 88: EN 14303, Thermal insulation products for building equipment and industrial installations — Factory made mineral wool (MW) products — Specification SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 5 EN 14304, Thermal insulation products for building equipment and industrial installations — Factory made flexible elastomeric foam (FEF) products — Specification EN 14305, Thermal insulation products for building equipment and industrial installations — Factory made cellular glass (CG) products — Specification EN 14306, Thermal insulation products for building equipment and industrial installations — Factory made calcium silicate (CS) products — Specification EN 14307,Thermal insulation products for building equipment and industrial installations — Factory made extruded polystyrene foam (XPS) products — Specification EN 14308, Thermal insulation products for building equipment and industrial installations — Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products — Specification EN 14309, Thermal insulation products for building equipment and industrial installations — Factory made products of expanded polystyrene (EPS) — Specification EN 14313, Thermal insulation products for building equipment and industrial installations — Factory made polyethylene foam (PEF) products — Specification EN 14314, Thermal insulation products for building equipment and industrial installations — Factory made phenolic foam (PF) products — Specification According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 6 1 Scope This European Standard specifies the requirements for factory made products of expanded polystyrene which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 180 °C to + 80 °C. Modified expanded polystyrene polymers with a higher temperature resistance are also covered by this standard. NOTE Below an operating temperature of - 50 °C, special tests regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturers’ advice should be heeded in all cases. The products are manufactured in the form of faced or unfaced boards, rolls, lags, pipe sections or other prefabricated ware. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This standard does not specify the required level or class of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this standard. This standard does not cover products for in situ insulation (for loose fill or poured insulation) or products for the insulation of the building structure. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 822, Thermal insulating products for building applications — Determination of length and width EN 823, Thermal insulating products for building applications — Determination of thickness EN 824, Thermal insulating products for building applications — Determination of squareness EN 825, Thermal insulating products for building applications — Determination of flatness EN 826, Thermal insulating products for building applications — Determination of compression behaviour EN 1602, Thermal insulating products for building applications — Determination of the apparent density EN 1603, Thermal insulating products for building applications — Determination of dimensional stability under constant normal laboratory conditions (23 °C/50 % relative humidity) EN 1604, Thermal insulating products for building applications — Determination of dimensional stability under specified temperature and humidity conditions EN 1606, Thermal insulating products for building applications — Determination of compressive creep EN 1607, Thermal insulating products for building applications — Determination of tensile strength perpendicular to faces SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 7 EN 12085, Thermal insulating products for building applications — Determination of linear dimensions of test specimens EN 12086, Thermal insulating products for building applications — Determination of water vapour transmission properties EN 12087, Thermal insulating products for building applications — Determination of long term water absorption by immersion EN 12088, Thermal insulating products for building applications — Determination of long term water absorption by diffusion EN 12089, Thermal insulating products for building applications — Determination of bending behaviour EN 12091, Thermal insulating products for building applications — Determination of freeze-thaw resistance EN 12431, Thermal insulating products for building applications — Determination of thickness for floating floor insulating products EN 12667, Thermal performance of building materials and products — Determination of thermal resistance by means of guarded hot plate and heat flow meter methods — Products of high and medium thermal resistance EN 12939, Thermal performance of building materials and products — Determination of thermal resistance by means of guarded hot plate and heat flow meter methods — Thick products of high and medium thermal resistance EN 13172, Thermal insulating products — Evaluation of conformity EN 13467, Thermal insulating products for building equipment and industrial installations — Determination of dimensions, squareness and linearity of preformed pipe insulation EN 13468, Thermal insulating products for building equipment and industrial installations — Determination of trace quantities of water soluble chloride, fluoride, silicate, and sodium ions and pH EN 13469, Thermal insulating products for building equipment and industrial installations — Determination of water vapour transmission properties of preformed pipe insulation EN 13470, Thermal insulating products for building equipment and industrial installations — Determination of the apparent density of preformed pipe insulation EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using data from reaction to fire tests EN 13823, Reaction to fire tests for building products — Building products excluding floorings exposed to the thermal attack by a single burning item EN 14706, Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature EN 14707, Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature of preformed pipe insulation EN 15715:2009, Thermal insulation products — Instructions for mounting and fixing for reaction to fire testing — Factory made products EN 29052-1, Acoustics — Determination of dynamic stiffness — Part 1: Materials used under floating floors in dwellings EN ISO 1182, Reaction to fire tests for building products — Non-combustibility test (ISO 1182:2002) SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 8 EN ISO 1716, Reaction to fire tests for building products — Determination of the heat of combustion
(ISO 1716:2002) EN ISO 8497, Thermal insulation — Determination of steady-state thermal transmission properties of thermal insulation for circular pipes (ISO 8497:1994) EN ISO 11925-2, Reaction to fire tests
— Ignitability of building products subjected to direct impingement of flame — Part 2: Single flame source-test (ISO 11925-2:2002) EN ISO 13787, Thermal insulation products for building equipment and industrial installations — Determination of declared thermal conductivity (ISO 13787:2003) 3 Terms, definitions, symbols, units and abbreviated terms 3.1 Terms and definitions For the purposes of this document the following terms and definitions apply. 3.1.1 Terms and definitions as given in EN ISO 9229:2007 3.1.1.1 pipe section (insulation) product in the shape of a cylindrical annulus which may be split
to facilitate application 3.1.1.2 board slab (insulation) rigid or semi-rigid product of rectangular shape and cross-section in which the thickness is uniform and substantially smaller than the other dimensions NOTE Boards are usually thinner than slabs. They may also be delivered in tapered form. 3.1.1.3 roll (insulation) product supplied in the form of a wound cylinder 3.1.1.4 lag segment rigid or semi-rigid insulation product for application on large diameter cylindrical or spherical equipment 3.1.2 Additional terms and definitions 3.1.2.1 expanded polystyrene (EPS) rigid cellular plastics insulation material, manufactured by moulding beads of expandable polystyrene or one of its copolymers and which has a closed cellular structure filled with air 3.1.2.2 expanded polystyrene block rigid insulation product or material generally of rectangular cross section and with a thickness not significantly smaller than the width. Blocks are supplied trimmed or untrimmed 3.1.2.3 expanded polystyrene board rigid insulation product (cut, moulded or continuously foamed) of rectangular shape and cross section in which the thickness is significantly smaller than the other dimensions
SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 9 NOTE Boards can be of uniform thickness or tapered. The board edges can be of various sorts (e.g. square, half lapped, tongue and groove). 3.1.2.4 level given value, which is the upper or lower limit of a requirement
NOTE The level is given by the declared value of the characteristic concerned 3.1.2.5 class combination of two levels of the same property between which the performance shall fall. 3.1.2.6 production line assemblage of equipment that produces products using a continuous process 3.1.2.7 production unit assemblage of equipment that produces products using a discontinuous process NOTE For ITT and FPC, units using the same process in one factory are considered together (as one production line). 3.1.2.8 prefabricated ware pieces cut, abraded or otherwise formed from a board or block of product e.g. elbows, T-pieces etc. 3.1.2.9 product material, element or component about which information is required. Refers to a construction product, as defined in the Construction Products Directive, from an individual producer 3.2 Symbols, units and abbreviated terms 3.2.1 Symbols and units used in this standard α
is the confidence level – b
is the width mm d
is the thickness mm Di
is the inside diameter mm D
is the water vapour permeability mg/(m·h·Pa) dD
is the declared thickness of a product mm ∆εb
is the relative change in width % ∆εl
is the relative change in length % ∆εd
is the relative change in thickness % Edyn
is the dynamic elasticity modulus MN/m2 k
is a factor related to the number of test results available - l
is the length mm SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 10 L
is the deviation from linearity mm λ90, 90
is the thermal conductivity of 90 % fractile and 90 % confidence level W/(m·K) λD
is the declared thermal conductivity W/(m·K) λi
is one test result of thermal conductivity W/(m·K) λmean
is the mean value of the measured thermal conductivity W/(m·K) µ
is the water vapour diffusion resistance factor – p
is the fractile value (quantile) – ρa
is the apparent density kg/m3 s'
is the dynamic stiffness MN/m3 σ10
is the compressive stress at 10 % deformation kPa σb
is the bending strength kPa σmt
is the tensile strength perpendicular to faces kPa Sb
s the deviation from squareness mm/m sλ
is the estimate of the standard deviation of the thermal conductivity W/(m·K) Smax
is the deviation from flatness mm sR
is the estimate of the standard deviation of the thermal resistance (m2·K)/W τ
is the shear strength kPa v
is the deviation of squareness mm WdV
is the water absorption by diffusion vol.-% Wlt
is the long-term water absorption by total immersion vol.-% Wlp
is the long-term water absorption by partial immersion kg/m2 X0
is the initial deformation (after 60 s from the beginning of the loading) mm Xct
is the absolute compressive creep mm or % Xt
is the deformation at time t mm Z
is the water vapour resistance (m2·h·Pa)/mg BS
is the symbol of the declared level for bending strength CC(i1/i2/y)σc is the symbol of the declared level for compressive creep CL
is the symbol of the declared level for water soluble chloride ions CS(10)
is the symbol of the declared level for compressive stress at 10 % deformation DS(N)
is the symbol of the declared class for dimensional stability under normal laboratory conditions SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 11 DS(T\L)
is the symbol of the declared level for dimensional stability under load and temperature F
is the symbol of the declared level of water soluble fluoride ions L
is the symbol of the declared class for length tolerances MU
is the symbol for the declared water vapour diffusion factor NA
is the symbol of the declared level of water soluble sodium ions
P
is the symbol of the declared class for flatness tolerance pH
is the symbol of the declared level for the pH-value S
is the symbol of the declared class for squareness tolerance SI
is the symbol of the declared level of water soluble silicate ions ST(+)
is the symbol of the declared level of maximum service temperature ST(–)
is the symbol of the declared level of minimum service temperature T
is the symbol of the declared class for thickness tolerance TR
is the symbol of the declared level for tensile strength perpendicular to faces W
is the symbol of the declared class for width tolerance WD(V)
is the symbol of the declared level for water absorption by diffusion WL(T)
is the symbol of the declared level for water absorption by total immersion WS
is the symbol of the declared level for short term water absorption Z
is the symbol of the declared water vapour resistance value 3.2.2 Abbreviated terms used in this standard EPS is Expanded PolyStyrene ITT is Initial Type Test ML is Manufacturer’s Literature FPC
is Factory Production Control 4 Requirements 4.1 General Product properties shall be assessed in accordance with Clause 5. To comply with this standard, products shall meet the requirements of Subclause 4.2, and the requirements of Subclause 4.3 as appropriate. NOTE
Information on additional properties is given in Annex E. One test result on a product property is the average of the measured values on the number of test specimens given in Table 12. SIST EN 14309:2010+A1:2013
EN 14309:2009+A1:2013 (E) 12 4.2 For all applications 4.2.1 Thermal conductivity For flat specimens, thermal conductivity shall be based upon measurements carried out in accordance with EN 12667 or EN 12939 for thick products. For cylindrical specimens EN ISO 8497 shall be used as specified in Subclause 5.3.2. In both cases, the thermal conductivity values shall be determined by the manufacturer and verified in accordance with EN ISO 13787. They shall be declared by the manufacturer according to the measuring standards mentioned above covering the product service temperature range. The following conditions apply: the measured values shall be expressed to three significant figures; the declared thermal conductivity curve shall be given as a limit curve, defined in EN ISO 13787; the value of the declared thermal conductivity, λD, shall be rounded upwards to the nearest 0,001 W/(m·K). The declared equation/ limit curve is the "declared reference" with three significant figures, that is to 0,000 1 W/(m·K)
used as a reference for the verification of the declaration. When thermal conductivity is declared as a table derived from the equation, rounding upwards to the next
0,001 W/(m·K) has to be done for the full range of the thermal conductivity. NOTE Determinations of the declared thermal conductivity of pipe sections, following EN ISO 8497, having joints in the metering area, include the effects of these joints as defined in EN ISO 23993. 4.2.2 Dimensions and tolerances 4.2.2.1 Linear dimensions The length, l, width, b, and thickness, d, of flat products shall be determined in accordance with EN 822 and EN 823.
The length, l, thickness, d, and inside diameter, Di, of pipe sections, segments and prefabricated ware shall be determined in accordance with EN 13467. No test result shall deviate from the declared values by more than the tolerances given in Table 1 for the labelled class. Table 1 — Dimensional tolerances Form of delivery Len
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.