SIST EN IEC 63522-1:2026

SLOVENSKI STANDARD
01-januar-2026
Električni releji - Preskusi in meritve - 7-1. del: Vizualni pregled in preverjanje mer
Electrical relays - Tests and Measurements - Part 1: Visual inspection and check of
dimensions
Elektromechanische Elementarrelais - Mess- und Prüfverfahren - Teil 7-1: Sichtprüfung
und Überprüfung der Abmessungen
Relais électriques - Essais et mesurages - Partie 1: Examen visuel et contrôle des
dimensions
Ta slovenski standard je istoveten z: EN IEC 63522-1:2025
ICS:
29.120.70 Releji Relays
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 63522-1

NORME EUROPÉENNE
EUROPÄISCHE NORM November 2025
ICS 29.120.70
English Version
Electrical relays - Tests and measurements - Part 1: Visual
inspection and check of dimensions
(IEC 63522-1:2025)
Relais électriques - Essais et mesurages - Partie 1: Elektromechanische Elementarrelais - Mess- und
Examen visuel et contrôle des dimensions Prüfverfahren - Teil 7-1: Sichtprüfung und Überprüfung der
(IEC 63522-1:2025) Abmessungen
(IEC 63522-1:2025)
This European Standard was approved by CENELEC on 2025-11-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63522-1:2025 E

European foreword
The text of document 94/1124/FDIS, future edition 1 of IEC 63522-1, prepared by TC 94 "Electrical
relays" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2026-11-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-11-30
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document is read in conjunction with EN IEC 63522-0:— .
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63522-1:2025 was approved by CENELEC as a European
Standard without any modification.

Under preparation. Stage at the time of publication: prEN IEC 63522-0:2025.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
2 3
IEC 63522-0 — Electrical relays - Tests and Measurements EN IEC 63522-0 —
- Part 0: General and Guidance
4 5
IEC 63522-41 — Electrical relays - Tests and measurements EN IEC 63522-41 —
- Part 41: Insulation coordination

Under preparation. Stage at the time of publication: IEC CDV 63522-0:2024.
Under preparation. Stage at the time of publication: prEN IEC 63522-0:2025.
Under preparation. Stage at the time of publication: IEC CDV 63522-41:2024.
Under preparation. Stage at the time of publication: prEN IEC 63522-41:2024.
IEC 63522-1 ®
Edition 1.0 2025-10
INTERNATIONAL
STANDARD
Electrical relays - Tests and measurements -
Part 1: Visual inspection and check of dimensions
ICS 29.120.70  ISBN 978-2-8327-0692-3

IEC 63522-1:2025-10(en)
IEC 63522-1:2025 © IEC 2025
CONTENTS
FOREWORD . 2
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test procedure . 4
4.1 Purpose . 4
4.2 Inspection procedure. 5
4.2.1 General. 5
4.2.2 Initial inspection . 5
4.2.3 Visual inspection . 5
4.2.4 Detailed inspection. 5
4.3 Check of dimensions . 5
4.3.1 General. 5
4.3.2 Kind of dimensions . 6
4.4 Conditions to be specified. 6
4.4.1 Inspection . 6
4.4.2 Check of dimensions . 7
5 Evaluation . 7
5.1 General . 7
5.2 Test report . 7
Bibliography . 8

IEC 63522-1:2025 © IEC 2025
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Electrical relays - Tests and measurements -
Part 1: Visual inspection and check of dimensions

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is no
...