SIST EN 353-1:2002

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Personal protective equipment against falls from a height - Part 1: Guided type fall arresters including a rigid anchor lineEquipement de protection individuelle contre les chutes de hauteur - Partie 1: Antichutes mobiles incluant un support d'assurage rigidePersönliche Schutzausrüstungen gegen Absturz - Teil 1: Steigschutzeinrichtungen einschließlich fester Führung13.340.99Druga varovalna opremaOther protective equipment13.340.60Protection against falling and slippingICS:SIST EN 353-1:2002enTa slovenski standard je istoveten z:EN 353-1:200201-november-2002SIST EN 353-1:2002SLOVENSKI
STANDARDSIST EN 353-1:19961DGRPHãþD







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 353-1May 2002ICS 13.340.99Supersedes EN 353-1:1992English versionPersonal protective equipment against falls from a height - Part1: Guided type fall arresters including a rigid anchor lineEquipement de protection individuelle contre les chutes dehauteur - Partie 1: Antichutes mobiles incluant un supportd'assurage rigidePersönliche Schutzausrüstungen gegen Absturz -Mitlaufende Auffanggeräte einschließlich fester FührungThis European Standard was approved by CEN on 12 March 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 353-1:2002 E



EN 353-1:2002 (E)2ContentspageForeword.31Scope.42Normative references.43Terms and definitions.44Requirements.54.1Design and ergonomics.54.2Materials and construction.54.3Locking.64.3.1Locking after conditioning.64.3.2Locking after optional conditioning.64.4Static strength.64.5Dynamic performance.64.6Corrosion resistance.64.7Marking and information.65Test methods.75.1Locking test after conditioning.75.1.1Apparatus.75.1.2Method.75.2Static strength test.75.2.1Apparatus.75.2.2Method.75.3Dynamic performance test.75.3.1Apparatus.75.3.2Method.75.4Corrosion test.76Marking.87Information supplied by the manufacturer.88Packaging.9Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or otherprovisions of EU Directives.10Bibliography.11



EN 353-1:2002 (E)3ForewordThis document EN 353-1:2002 has been prepared by Technical Committee CEN/TC 160 "Protection against fallsfrom a height including working belts", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at the latestby November 2002.This document supersedes EN 353-1:1992. This new edition contains the old text of the standard and incorporatessome urgent amendments that are intended to give additional information and clarify inconsistencies. Acomprehensive revision of the standard will follow at a later stage.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.



EN 353-1:2002 (E)41 ScopeThis European Standard specifies the requirements, test methods, marking, information supplied by the manufacturerand packaging for guided type fall arresters including a rigid anchor line usually attached to or integrated in fixedladders or rungs adequately adjusted to suitable structures. Guided type fall arresters including a rigid anchor lineconforming to this European Standard are sub-systems constituting one of the fall arrest systems covered by EN 363,when combined with a full body harness specified in EN 361 including a front attachment point located appropriatelyin relation to the fall arrester. Other types of fall arresters are specified in EN 353-2 or in EN 360. Energy absorbersare specified in EN 355.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references, the latest edition of thepublication referred to applies (including amendments).EN 354:2002, Personal protective equipment against falls from a height – Lanyards.EN 355:2002, Personal protective equipment against falls from a height - Energy absorbers.EN 362, Personal protective equipment against falls from a height – Connectors.EN 363:2002, Personal protective equipment against falls from a height - Fall arrest systems.EN 364:1992, Personal protective equipment against falls from a height - Test methods.EN 365:1992, Personal protective equipment against falls from a height - General requirements for instructions foruse and for marking.3 Terms and definitionsFor the purposes of this European Standard, the following terms and definitions apply.3.1guided type fall arrester including a rigid anchor linesub-system consisting of a rigid anchor line, a self-locking guided type fall arrester which is attached to the rigidanchor line and a connector or a connector-terminated lanyard. An energy dissipating function may be installedbetween the fall arrester and the anchor line or an energy absorber may be incorporated in the lanyard or in theanchor line [EN 363]3.2guided type fall arresterfall arrester with a self-locking function and a guide facility. The guided type fall arrester travels along an anchor line,accompanies the user without requiring manual adjustment during upward or downward changes of position and locksautomatically on the anchor line when a fall occurs [EN 363]3.3rigid anchor lineconnecting element specified for a sub-system with a guided type fall arrester. A rigid anchor line may be a rail or awire rope and is intended for securing to a structure in such a way that lateral movements of the line are limited[EN 363]



EN 353-1:2002 (E)53.4energy absorberelement or a component of a fall arr
...