SIST EN 14707:2013

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Ugotavljanje najvišje temperature servisiranja predoblikovanih cevnih izolacijWärmedämmstoffe für die Haustechnik und für betriebstechnische Anlagen - Bestimmung der oberen Anwendungsgrenztemperatur von vorgeformten RohrdämmstoffenProduits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Détermination de la température maximale de service des coquilles isolantes préforméesThermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 14707:2012SIST EN 14707:2013en,fr,de01-februar-2013SIST EN 14707:2013SLOVENSKI
STANDARDSIST EN 14707:2006+A1:20081DGRPHãþD



SIST EN 14707:2013



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14707
October 2012 ICS 91.100.60 Supersedes EN 14707:2005+A1:2007English Version
Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation
Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Détermination de la température maximale de service des coquilles isolantes préformées
Wärmedämmstoffe für die Haustechnik und für betriebstechnische Anlagen - Bestimmung der oberen Anwendungsgrenztemperatur von vorgeformten Rohrdämmstoffen This European Standard was approved by CEN on 24 August 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14707:2012: ESIST EN 14707:2013



EN 14707:2012 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .44 Principle .45 Apparatus .46 Test specimens .76.1 Dimensions of test specimens .76.2 Number of test specimens .76.3 Conditioning of test specimens .87 Procedure .87.1 Test conditions .87.2 Test procedure .88 Calculation and expression of results .98.1 Thickness deformation versus time .98.2 Additional tests and/or observations . 118.3 Internal self heating . 119 Accuracy of measurement . 1110 Test report . 11Annex A (normative)
Modifications of and additions to the general test method for mineral wool products . 13A.1 Introduction . 13A.2 Dimensions of test specimens . 13A.3 Procedure . 13A.3.1 Test conditions . 13A.3.2 Test procedure . 13A.4 Additional tests and/or observations . 13A.5 Test for internal self-heating . 13Annex B (normative)
Modifications of and additions to the general test method for polyethylene foam (PEF) and flexible elastomeric foam (FEF) products. 15B.1 Introduction . 15B.2 Apparatus . 15B.3 Dimensions of test specimens . 15B.4 Test procedure . 16B.5 Dimensional changes . 17Annex C (normative)
Modifications of and additions to the general test method for phenolic foam products . 18C.1 Introduction . 18C.2 Conditioning of test specimens . 18C.3 Test procedure . 18C.4 Additional tests and/or observations . 18Bibliography . 20 SIST EN 14707:2013



EN 14707:2012 (E) 3 Foreword This document (EN 14707:2012) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14707:2005+A1:2007. The main technical changes that have been made in this new version of EN 14707 are: a) 6.1, Dimensions of test specimens has been modified; b) B.3, Dimension of test specimens has been completed. This European Standard is one of a series of European Standards which specify test methods for determining dimensions and properties of thermal insulating materials and products. It supports a series of product standards for thermal insulating materials and products which derive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (Directive 89/106/EEC) through the consideration of the essential requirements. This European Standard has been prepared for products used to insulate building equipment and industrial installations, but it may also be applied to products used in other areas. A similar standard is available for testing of flat products: EN 14706, Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 14707:2013



EN 14707:2012 (E) 4 1 Scope This European Standard specifies the equipment and procedures for determining the maximum service temperature for preformed pipe insulation. It is applicable to thermal insulating products. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12429, Thermal insulating products for building applications — Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 13467, Thermal insulating products for building equipment and industrial installations — Determination of dimensions, squareness and linearity of preformed pipe insulation EN 14706, Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature 3 Terms and definitions For the purposes of this document, the following term and definition applies. 3.1 maximum service temperature highest temperature at which the insulation product, when installed a the recommended thickness in a given application, continues to function within specified limits of performance [SOURCE: EN ISO 9229:2007, 2.6.9.1] Note 1 to entry: The required performance may be in the areas of dimensional stability, thermal properties, and mechanical properties as well as changes in appearance and resistance against creation of hazards such as internal self-heating (see annexes and requirements in the relevant product standard). Note 2 to entry: In the present test procedure, which is used as a reference, the test specimen is exposed to a temperature difference going from ambient to the maximum service temperature. This may not reflect the actual application conditions when products are exposed to different temperatures on the two main faces, e.g. in multi-layer systems or for faced products where the facing may limit the maximum service temperature. 4 Principle Measure thickness and length after one sided heat treatment for a specified time period, at the maximum service temperature, achieved using a specified rate of temperature increase. The thickness of the test specimen is measured during heat treatment and the length only after cooling to ambient temperature. The procedure may be an iterative process. Additional requirements for assessing the maximum service temperature of specific materials are described in normative annexes to this European Standard or the relevant product standard or any other European Technical Specification. 5 Apparatus A general arrangement of the apparatus is indicated in Figure 1 and is comprised of: SIST EN 14707:2013



EN 14707:2012 (E) 5 5.1 Hot pipe, with a uniform temperature distribution in the measuring zone on the hot surface and a heat flux perpendicular to the surface of the pipe within the measuring zone (two pipes are required, with diameters that fulfil the requirements of 6.1).
The hot pipe shall be linear to within ± 1 mm in the measuring zone at ambient temperature. The hot pipe shall be capable of being controlled to within ± 2 % of a predetermined temperature ± 10 °C whichever is smaller over the central 60 % of the total pipe length. The hot pipe shall be capable of being heated at 50 °C/h and/or 300 °C/h. 5.2 End insulation, with a gap as small as possible between end insulation and guard piece of the test specimen (e.g. ≤ 3 mm) which will permit free movement during the test of the test specimen. 5.3 Temperature sensors, (e.g. thermocouples) capable of recording the hot surface temperature of the test pipe to the nearest ± 1 % in centigrade but not less than ± 1 °C, which are placed within grooves on the hot pipe. 5.4 Flexible metal foil, 3 pieces, (e.g. brass) capable of exerting a uniform pressure of 500 Pa on the upper surface of the test specimen along its testing length of (500 ± 5) mm and the two end guards, length (250 ± 5) mm.
The pressure shall be calculated using the area: e.g. the test length of 500 mm times the diameter of the hot pipe. 5.5 Device, e.g. electromechanical for measuring the thickness of the test specimen during the test to the nearest 0,1 mm. When determining the thickness of the test specimen, the thermal movement of the apparatus (e.g. quartz rod) shall be taken into account up to the maximum service temperature. SIST EN 14707:2013



EN 14707:2012 (E) 6 Dimensions in millimetres
Key 1 device for measuring thickness, e. g. electromechanical device
2a
test length of the test specimen 2b test specimen end guard 3 end insulation 4 small gap 5 circumferential joints 6 thermocouples 7 hot pipe 8 power supply and temperature control l length of the hot pipe between the end insulation a) General arrangement SIST EN 14707:2013



EN 14707:2012 (E) 7 Dimensions in millimetres
Key 1 device for measuring thickness, e.g. electromechanical device 2 thermocouple 3 hot pipe
4 test speci
...