SIST EN ISO 14245:2021/A1:2026

SLOVENSKI STANDARD
01-april-2026
Plinske jeklenke - Specifikacije in preskušanje ventilov za jeklenke za utekočinjeni
naftni plin (UNP) - Samozaporni ventili - Dopolnilo A1 (ISO 14245:2021/Amd 1:2025)
Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing -
Amendment 1 (ISO 14245:2021/Amd 1:2025)
Gasflaschen - Spezifikation und Prüfung von Flaschenventilen für Flüssiggas (LPG) -
Selbstschließend - Änderung 1 (ISO 14245:2021/Amd 1:2025)
Bouteilles à gaz - Spécifications et essais pour valves de bouteilles de GPL - Fermeture
automatique - Amendement 1 (ISO 14245:2021/Amd 1:2025)
Ta slovenski standard je istoveten z: EN ISO 14245:2021/A1:2025
ICS:
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 Tlačni regulatorji Pressure regulators
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 14245:2021/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2025
EUROPÄISCHE NORM
ICS 23.020.35
English Version
Gas cylinders - Specifications and testing of LPG cylinder
valves - Self-closing - Amendment 1 (ISO
14245:2021/Amd 1:2025)
Bouteilles à gaz - Spécifications et essais pour valves de Gasflaschen - Spezifikation und Prüfung von
bouteilles de GPL - Fermeture automatique - Flaschenventilen für Flüssiggas (LPG) -
Amendement 1 (ISO 14245:2021/Amd 1:2025) Selbstschließend - Änderung 1 (ISO 14245:2021/Amd
1:2025)
This amendment A1 modifies the European Standard EN ISO 14245:2021; it was approved by CEN on 25 July 2025.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14245:2021/A1:2025 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 14245:2021/A1:2025) has been prepared by Technical Committee ISO/TC 58
"Gas cylinders" in collaboration with Technical Committee CEN/TC 286 “Liquefied petroleum gas
equipment and accessories” the secretariat of which is held by NSAI.
This Amendment to the European Standard EN ISO 14245:2021 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by June 2026, and
conflicting national standards shall be withdrawn at the latest by June 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 14245:2021/Amd 1:2025 has been approved by CEN as EN ISO 14245:2021/A1:2025
without any modification.
International
Standard
ISO 14245
Third edition
Gas cylinders — Specifications and
2021-06
testing of LPG cylinder valves —
Self-closing
AMENDMENT 1
2025-12
AMENDMENT 1
Bouteilles à gaz — Spécifications et essais pour valves de
bouteilles de GPL — Fermeture automatique
AMENDEMENT 1
Reference number
ISO 14245:2021/Amd.1:2025(en) © ISO 2025

ISO 14245:2021/Amd.1:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 14245:2021/Amd.1:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2, Cylinder
fittings, in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 286, Liquefied petroleum gas equipment and accessories,in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iii
ISO 14245:2021/Amd.1:2025(en)
Gas cylinders — Specifications and testing of LPG cylinder
valves — Self-closing
AMENDMENT 1
Clause 2, Normative references
Add the following normative reference:
MIL-STD-810G:2008, Department of Defence Test Method Standard, Environmental Engineering Considerations
and Laboratory Tests
3.13
Delete term and definition and re-number the following terms and definitions.

4.2
Add the following new subclause:
4.2.5  Adhesives
Where used, adhesives shall be proven compatible with LPG in accordance with recognized international,
regional or national standards.

4.3.3, first sentence
Replace sentence with the following:
Valve inlet connections shall conform to an international, regional or national standard or proprietary
designs that have been qualified to an acceptable industry standard.

4.3.3, NOTE
Replace NOTE with the following:
NOTE 1 Valve inlet connection standards are, for example, ISO 11363-1 and ISO 15245-1.
NOTE 2 Qualification procedures for proprietary valve inlet connection designs are, for example, given in
ISO 10692-2.
4.3.3, third paragraph
Replace the reference "Table 3" with "Table 4".

ISO 14245:2021/Amd.1:2025(en)
4.3.4, first sentence
Replace sentence with the following:
Valve outlet connections shall conform to an international, regional or national standard or proprietary
designs that have been qualified to an acceptable industry standard.

4.3.4, NOTE
Replace NOTE with the following:
NOTE 1 Valve outlet connection standards are, for example, ISO 5145 and EN 15202.
NOTE 2 Qualification procedures for proprietary valve outlet connection designs are, for example, given in CGA V-1.

4.4.1
Add the following paragraph at the end of the subclause:
Where threaded joints are used within the valve, an anaerobic sealant may be used if proven compatible
with LPG in accordance with recognized international, regional (e.g. EN 751-1) or national standards.

4.4.4
Add the following indents and the example to the end of the list:
d) There shall be sufficient thread engagement between the vent screw and the fixed liquid level gauge to
allow metal to metal contact in the event of absence of the seal.
e) The dip tube shall be securely fitted to the valve to ensure that it does not disassemble during installation
or operation.
EXAMPLE Using adhesive, press fitting or any other mechanical means.

4.4.9
Add the following paragraph and example at the end of the subclause:
The sediment tube shall be securely fitted to the valve to ensure that it does not disass
...