SIST EN ISO 4943:2022

SLOVENSKI STANDARD
01-november-2022
Nadomešča:
SIST EN 24943:1997
SIST EN 24943:1997/AC:1997
Jeklo in lito železo - Določevanje bakra - Plamenska atomska absorpcijska
spektrometrična metoda (ISO 4943:2022)
Steel and cast iron - Determination of copper content - Flame atomic absorption
spectrometric method (ISO 4943:2022)
Stahl und Gusseisen - Bestimmung des Kupfergehalts -
Flammenatomabsorptionsspektrometrisches Verfahren (ISO 4943:2022)
Aciers et fontes - Détermination de la teneur en cuivre - Méthode par spectrométrie
d'absorption atomique dans la flamme (ISO 4943:2022)
Ta slovenski standard je istoveten z: EN ISO 4943:2022
ICS:
77.040.30 Kemijska analiza kovin Chemical analysis of metals
77.080.01 Železne kovine na splošno Ferrous metals in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 4943
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2022
EUROPÄISCHE NORM
ICS 77.080.01 Supersedes EN 24943:1990, EN 24943:1990/AC:1991
English Version
Steel and cast iron - Determination of copper content -
Flame atomic absorption spectrometric method (ISO
4943:2022)
Aciers et fontes - Détermination de la teneur en cuivre - Stahl und Gusseisen - Bestimmung des Kupfergehalts -
Méthode par spectrométrie d'absorption atomique Flammenatomabsorptionsspektrometrisches
dans la flamme (ISO 4943:2022) Verfahren (ISO 4943:2022)
This European Standard was approved by CEN on 5 August 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4943:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 4943:2022) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee CEN/TC 459/SC 2 “Methods of chemical analysis for iron and
steel ” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2023, and conflicting national standards shall
be withdrawn at the latest by March 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 24943:1990, EN 24943:1990/AC:1991.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 4943:2022 has been approved by CEN as EN ISO 4943:2022 without any modification.

INTERNATIONAL ISO
STANDARD 4943
Second edition
2022-08
Steel and cast iron — Determination
of copper content — Flame atomic
absorption spectrometric method
Aciers et fontes — Détermination de la teneur en cuivre — Méthode
par spectrométrie d'absorption atomique dans la flamme
Reference number
ISO 4943:2022(E)
ISO 4943:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 4943:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Reagents . 1
6 Apparatus . 2
6.1 Atomic absorption spectrometer . 2
6.1.1 Minimum precision . 3
6.1.2 Limit of detection . 3
6.1.3 Calibration linearity . 3
6.1.4 Characteristic concentration . 3
6.2 Ancillary equipment . 3
7 Sampling . 3
8 Procedure .3
8.1 Test portion . 3
8.2 Blank test . 4
8.3 Determination . 4
8.3.1 Preparation of the test solution . 4
8.3.2 Preparation of the calibration solutions . 4
8.3.3 Adjustment and optimization of atomic absorption spectrometer . 6
8.3.4 Spectrometric measurements . 7
8.4 Plotting the calibration curve . 7
9 Expression of results . 7
10 Precision . 8
11 Test report . 8
Annex A (normative) Procedures for the determination of instrumental criteria .10
Annex B (informative) Additional information on the international interlaboratory
precision test .13
Annex C (informative) Graphical representation of precision data .14
Bibliography .15
iii
ISO 4943:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 1, Methods
of determination of chemical composition, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 459/SC 2, Methods of chemical analysis for iron
and steel, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
This second edition cancels and replaces the first edition (ISO 4943:1985), which has been technically
revised. The main changes are as follows:
— extension of the determination range;
— re-organization of a precision test;
— re-assessment of the precision data.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 4943:2022(E)
Steel and cast iron — Determination of copper content —
Flame atomic absorption spectrometric method
1 Scope
This document specifies a flame atomic absorption spectrometric method for the determination of
copper in steel and cast iron.
The method is applicable to copper contents in the range of 0,003 % (mass fraction) to 3,0 % (mass
fraction).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 648, Laboratory glassware — Single-volume pipettes
ISO 1042, Laboratory glassware — One-mark volumetric flasks
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 14284, Steel and iron — Sampling and preparation of samples for the determination of chemical
composition
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Principle
Dissolution of a test portion in a mixture of hydrochloric, nitric and perchloric acids.
Nebulization of the test solution into an air/acetylene flame of an atomic absorption spectrometer.
Spectrometric measurement of the atomic absorption of the 324,7 nm or 327,4 nm spectral line emitted
by a copper hollow-cathode lamp.
NOTE Other suitable radiation sources can also be used.
5 Reagents
During the analysis, unless otherwise stated, use only reagents of recognized analytical grade and only
grade 2 water as specified in ISO 3696.
5.1 Pure iron, containing less than 0,000 5 % (mass fraction) of copper or having a very low and
known copper content.
ISO 4943:2022(E)
5.2 Hydrochloric acid-nitric acid mixture.
Mix three parts by volume of hydrochloric acid (ρ about 1,19 g/ml), one part by volume of nitric acid (ρ
about 1,40 g/ml), and two parts by volume of water.
Prepare this mixture immediately before use.
5.3 Hydrochloric, nitric and perchloric acids mixture.
Mix 20 ml of hydrochloric acid (ρ about 1,19 g/ml) with 55 ml of nitric acid (ρ about 1,40 g/ml) and
75 ml of perchloric acid (ρ about 1,54 g/ml).
NOTE Perchloric acid (ρ about 1,67 g/ml) can also be used. 100 ml of perchloric acid (ρ about 1,54 g/ml) are
equivalent to 79 ml of perchloric acid (ρ about 1,67 g/ml).
5.4 Copper standard solution, 1,0 g/l.
Weigh (1,000 ± 0,001) g of copper [purity >99,95 % (mass fraction)]. Transfer into a 400 ml beaker,
add 25 ml of nitric acid (ρ about 1,40 g/ml, diluted 1 + 4) and cover with a watch-glass. Heat gently
to complete dissolution. Allow to cool, transfer the solution quantitatively into a 1 000 ml one-mark
volumetric flask, dilute to the mark with water and mix.
1 ml of this standard solution contains 1 mg of Cu.
5.5 Copper standard solution, 20 mg/l.
Transfer 20,0 ml of the standard solution (5.4) into a 1 000 ml one-mark volumetric flask, dilute to the
mark with water and mix.
1 ml of this standard solution contains 20 μg of Cu.
Prepare this standard solution immediately before use.
6 Apparatus
All volumetric glassware shall be class A, in accordance with ISO 648 or ISO 1042 as appropriate.
All glassware shall first be washed in hydrochloric acid (ρ about 1,19 g/ml, diluted 1 + 1), and then
in water. The quantity of copper present in the beakers and flasks can be checked by measuring the
absorption of distilled water introduced in the glassware after the acid wash.
Ordinary laboratory apparatus and the following shall be used.
6.1 Atomic absorption spectrometer
The spectrometer shall be equipped with a copper hollow-cathode lamp, and supplied with air and
acetylene sufficiently pure to give a steady clear fuel-lean flame, free from water and oil, and free from
copper.
NOTE Other suitable radiation sources can also be used.
The atomic absorption spectrometer used will be satisfactory if, after optimization in accordance with
8.3.4, the limit of detection and characteristic concentration are in reasonable agreement with the
values given by the manufacturer and it meets the precision criteria given in 6.1.1 to 6.1.3.
The instrument should also conform to the additional performance requirement given in 6.1.4.
ISO 4943:2022(E)
6.1.1 Minimum precision
Use the procedures described in Annex A. Calculate the standard deviation of 10 measurements of the
absorbance of the most concentrated calibration solution. This standard deviation shall not exceed
1,0 % of the mean absorbance.
Calculate the standard deviation of 10 measurements of the absorbance of the least concentrated
calibration solution (excluding the zero member). This standard deviation shall not exceed 0,5 % of the
mean absorbance of the most concentrated calibration solution.
6.1.2 Limit of detection
Use the procedures described in Annex A. The li
...