SIST EN IEC 62148-11:2025

SLOVENSKI STANDARD
01-april-2025
Aktivne komponente in naprave optičnih vlaken - Standardi oblike in vmesnika -
11. del: Integrirani modulatorji z lasersko diodo s 14 kontakti in moduli z lasersko
diodo za črpanje (IEC 62148-11:2024)
Fibre optic active components and devices - Package and interface standards - Part 11:
14-pin modulator integrated laser diode modules and pump laser diode modules (IEC
62148-11:2024)
Aktive Lichtwellenleiterbauelemente und -geräte – Gehäuse- und Schnittstellennormen
– Teil 11: 14-polige modulare integrierte Laserdiodenmodule und
Pumplaserdiodenmodule (IEC 62148-11:2024)
Composants et dispositifs actifs fibroniques - Normes de boîtier et d’interface - Partie 11:
Modules à diodes laser à modulateur intégré et à diodes laser de pompage de 14
broches (IEC 62148-11:2024)
Ta slovenski standard je istoveten z: EN IEC 62148-11:2025
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62148-11

NORME EUROPÉENNE
EUROPÄISCHE NORM February 2025
ICS 33.180.20 Supersedes EN 62148-11:2009
English Version
Fibre optic active components and devices - Package and
interface standards - Part 11: 14-pin modulator integrated laser
diode modules and pump laser diode modules
(IEC 62148-11:2024)
Composants et dispositifs actifs fibroniques - Normes de Aktive Lichtwellenleiterbauelemente und -geräte - Gehäuse-
boîtier et d'interface - Partie 11: Modules à diodes laser à und Schnittstellennormen - Teil 11: 14-polige modulare
modulateur intégré de 14 broches et à diodes laser de integrierte Laserdiodenmodule und
pompage de 14 broches Pumplaserdiodenmodule
(IEC 62148-11:2024) (IEC 62148-11:2024)
This European Standard was approved by CENELEC on 2025-01-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62148-11:2025 E

European foreword
The text of document 86C/1925/CDV, future edition 3 of IEC 62148-11, prepared by SC 86C "Fibre
optic systems, sensing and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN IEC 62148-11:2025.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2026-02-28
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-02-29
document have to be withdrawn
This document supersedes EN 62148-11:2009 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62148-11:2024 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60793-2-50 NOTE Approved as EN IEC 60793-2-50
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 61754 series Fibre optic interconnecting devices and passive EN 61754 series
components - Fibre optic connector interfaces
IEC 62148-1 - Fibre optic active components and devices - EN IEC 62148-1 -
Package and interface standards - Part 1:
General and guidance
IEC 62148-11 ®
Edition 3.0 2024-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic active components and devices – Package and interface standards –

Part 11: 14-pin modulator integrated laser diode modules and pump laser diode

modules
Composants et dispositifs actifs fibroniques – Normes de boîtier et d’interface –

Partie 11: Modules à diodes laser à modulateur intégré de 14 broches et à

diodes laser de pompage de 14 broches

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20  ISBN 978-2-8327-0086-0

– 2 – IEC 62148-11:2024 © IEC 2024
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 6
3.1 Terms and definitions . 6
3.2 Abbreviated terms . 6
4 Classification . 6
5 Specifications . 7
5.1 14-pin modulator integrated laser diode modules . 7
5.1.1 Pigtail interface . 7
5.1.2 Electrical interface . 7
5.1.3 Mechanical interface . 8
5.1.4 Case outline . 8
5.2 14-pin pump laser diode modules . 9
5.2.1 Pigtail interface . 9
5.2.2 Electrical interface . 9
5.2.3 Mechanical interface . 10
5.2.4 Case outline . 10
Bibliography . 11

Figure 1 – Electrical terminal numbering assignments (viewed from the top of the
module) . 7
Figure 2 – Case outline for 14-pin modulator integrated laser diode modules . 8
Figure 3 – Electrical terminal numbering assignments (viewed from the top of the
module) . 9
Figure 4 – Case outline for 14-pin pump laser diode modules . 10

Table 1 – Pin-function definitions for modulator integrated laser diode modules . 7
Table 2 – Pin function definitions for pump laser diode modules . 9

IEC 62148-11:2024 © IEC 2024 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
PACKAGE AND INTERFACE STANDARDS –

Part 11: 14-pin modulator integrated laser diode modules and
pump laser diode modules
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 62148-11 has been
...