SIST EN ISO 1179-2:2023
(Main)Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2022)
Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2022)
This document specifies the dimensions, performance requirements and test procedures for heavyduty (S series) and light-duty (L series) stud ends with threads, and the elastomeric sealing (type E)
that is used with them as defined in ISO 228-1.
Heavy-duty (S series) stud ends with type E sealing in accordance with this document can be used
at working pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing
in accordance with this document can be used at working pressures up to 25 MPa (250 bar). The
permissible working pressure depends upon size, materials, design, working conditions, application,
etc.
This document is applicable to connectors detailed in ISO 8434-1, ISO 8434-2 and ISO 8434-6.
NOTE The Introduction gives recommendations for ports and stud ends to be used for new designs in
hydraulic and pneumatic fluid power applications
Leitungsanschlüsse für allgemeine Anwendung und Fluidtechnik - Einschraublöcher und Einschraubzapfen mit Gewinde nach ISO 228-1 und Elastomerdichtung oder metallener Dichtkante - Teil 2: Einschraubzapfen mit Elastomerdichtung (Form E), schwere (S) und leichte Reihe (L) (ISO 1179-2:2022)
Dieses Dokument legt Maße, Leistungsanforderungen und Prüfverfahren für Einschraubzapfen der schweren Reihe (S-Reihe) und der leichten Reihe (L-Reihe) mit Gewinde und die damit verwendete Elastomerdichtung (Form E) nach ISO 228 1 fest.
Einschraubzapfen der schweren Reihe (S-Reihe) mit Dichtung der Form E, die diesem Dokument entsprechen, können bei Arbeitsdrücken bis 63 MPa (630 bar) eingesetzt werden. Einschraubzapfen der leichten Reihe (L-Reihe) mit Dichtung der Form E, die diesem Dokument entsprechen, können bei Arbeitsdrücken bis 25 MPa (250 bar) eingesetzt werden. Der zulässige Arbeitsdruck ist von Größe, Werkstoffen, Konstruktion, Betriebsbedingungen, Anwendung, usw. abhängig.
Dieses Dokument ist anwendbar für Verschraubungen nach ISO 8434 1, ISO 8434 2 und ISO 8434 6.
ANMERKUNG Die Einleitung enthält Empfehlungen für Einschraublöcher und -zapfen, die für Neukonstruktionen in hydraulischen und pneumatischen Kraftübertragungsanlagen zu verwenden sind.
Raccordements pour applications générales et transmissions hydrauliques et pneumatiques - Orifices et éléments mâles à filetage ISO 228-1 à joint en élastomère ou étanchéité métal sur métal - Partie 2: Éléments mâles de séries légère (série L) et lourde (série S) avec joint en élastomère (type E) (ISO 1179-2:2022)
Le présent document spécifie les dimensions, les exigences de performance et les modes opératoires des éléments mâles de série lourde (série S) et de série légère (série L) à filetage et à joint élastomère (type E) qui est utilisé avec ceux-ci, tel que défini dans l’ISO 228‑1.
Les éléments mâles de série lourde (série S) avec étanchéité de type E conformes au présent document peuvent être utilisés jusqu’à des pressions d’utilisation de 63 MPa (630 bar). Les éléments mâles de série légère (série L) avec étanchéité de type E conformes au présent document peuvent être utilisés jusqu’à des pressions d’utilisation de 25 MPa (250 bar). La pression d’utilisation admissible dépend des dimensions, des matériaux, de la conception, des conditions d’exploitation, des applications, etc.
Le présent document s’applique aux raccords de l’ISO 8434‑1, de l’ISO 8434‑2 et de l’ISO8434-6.
NOTE L’introduction donne des recommandations pour les orifices et les éléments mâles destinés à être utilisés pour de nouvelles conceptions dans des applications de transmissions hydrauliques et pneumatiques.
Priključki za splošno uporabo in za fluidno tehniko - Odprtine in priključki z navoji po ISO 228-1 z elastomernim ali kovinskim tesnjenjem - 2. del: Zelo obremenjeni ravni priključki (vrsta S) in malo obremenjeni ravni priključki (vrsta L) z elastomernim tesnjenjem (tip E) (ISO 1179-2:2022)
Ta dokument določa mere, zahtevane lastnosti in preskusne postopke za zelo obremenjene (vrsta S) in malo obremenjene (vrsta L) priključke z navoji ter za elastomerno tesnjenje (tipa E), ki se z njimi uporablja, kot je opredeljeno v standardu ISO 228-1. Zelo obremenjene priključke (vrsta S) s tesnjenjem tipa E v skladu s tem dokumentom je mogoče uporabljati pri delovnem tlaku do 63 MPa (630 barov). Malo obremenjene priključke (vrsta S) s tesnjenjem tipa E v skladu s tem dokumentom je mogoče uporabljati pri delovnem tlaku do 25 MPa (250 barov). Dovoljeni delovni tlak je odvisen od velikosti, materialov, oblike, delovnih pogojev, uporabe itd. Ta dokument se uporablja za priključke, podrobno opisane v standardih ISO 8434-1, ISO 8434-2 in ISO 8434-6. OPOMBA: V uvodu so navedena priporočila glede odprtin in priključkov z navoji, ki jih je treba za hidravlično in pnevmatsko fluidno tehniko uporabiti pri novem projektiranju.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 1179-2:2023
01-januar-2023
Nadomešča:
SIST EN ISO 1179-2:2014
Priključki za splošno uporabo in za fluidno tehniko - Odprtine in priključki z navoji
po ISO 228-1 z elastomernim ali kovinskim tesnjenjem - 2. del: Zelo obremenjeni
ravni priključki (vrsta S) in malo obremenjeni ravni priključki (vrsta L) z
elastomernim tesnjenjem (tip E) (ISO 1179-2:2022)
Connections for general use and fluid power - Ports and stud ends with ISO 228-1
threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and
light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2022)
Leitungsanschlüsse für allgemeine Anwendung und Fluidtechnik - Einschraublöcher und
Einschraubzapfen mit Gewinde nach ISO 228-1 und Elastomerdichtung oder metallener
Dichtkante - Teil 2: Einschraubzapfen mit Elastomerdichtung (Form E), schwere (S) und
leichte Reihe (L) (ISO 1179-2:2022)
Raccordements pour applications générales et transmissions hydrauliques et
pneumatiques - Orifices et éléments mâles à filetage ISO 228-1 à joint en élastomère ou
étanchéité métal sur métal - Partie 2: Éléments mâles de séries légère (série L) et lourde
(série S) avec joint en élastomère (type E) (ISO 1179-2:2022)
Ta slovenski standard je istoveten z: EN ISO 1179-2:2022
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
SIST EN ISO 1179-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 1179-2:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 1179-2:2023
EN ISO 1179-2
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 23.100.40 Supersedes EN ISO 1179-2:2013
English Version
Connections for general use and fluid power - Ports and
stud ends with ISO 228-1 threads with elastomeric or
metal-to-metal sealing - Part 2: Heavy-duty (S series) and
light-duty (L series) stud ends with elastomeric sealing
(type E) (ISO 1179-2:2022)
Raccordements pour applications générales et Leitungsanschlüsse für allgemeine Anwendung und
transmissions hydrauliques et pneumatiques - Orifices Fluidtechnik - Einschraublöcher und Einschraubzapfen
et éléments mâles à filetage ISO 228-1 à joint en mit Gewinde nach ISO 228-1 und Elastomerdichtung
élastomère ou étanchéité métal sur métal - Partie 2: oder metallener Dichtkante - Teil 2: Einschraubzapfen
Éléments mâles de séries légère (série L) et lourde mit Elastomerdichtung (Form E), schwere (S) und
(série S) avec joint en élastomère (type E) (ISO 1179- leichte Reihe (L) (ISO 1179-2:2022)
2:2022)
This European Standard was approved by CEN on 13 November 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1179-2:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 1179-2:2023
EN ISO 1179-2:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 1179-2:2023
EN ISO 1179-2:2022 (E)
European foreword
This document (EN ISO 1179-2:2022) has been prepared by Technical Committee ISO/TC 131 "Fluid
power systems" in collaboration with Technical Committee CEN/TC 459/SC 10 “Steel tubes, and iron
and steel fittings” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1179-2:2013.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 1179-2:2022 has been approved by CEN as EN ISO 1179-2:2022 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 1179-2:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 1179-2:2023
INTERNATIONAL ISO
STANDARD 1179-2
Third edition
2022-11
Connections for general use and fluid
power — Ports and stud ends with
ISO 228-1 threads with elastomeric or
metal-to-metal sealing —
Part 2:
Heavy-duty (S series) and light-duty
(L series) stud ends with elastomeric
sealing (type E)
Raccordements pour applications générales et transmissions
hydrauliques et pneumatiques — Orifices et éléments mâles à filetage
ISO 228-1 à joint en élastomère ou étanchéité métal sur métal —
Partie 2: Éléments mâles de séries légère (série L) et lourde (série S)
avec joint en élastomère (type E)
Reference number
ISO 1179-2:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 1179-2:2023
ISO 1179-2:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 1179-2:2023
ISO 1179-2:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Interchangeability warning .2
5 Dimensions .2
6 Elastomeric seals .3
7 Requirements . 5
7.1 Working pressure . 5
7.2 Performance . 5
8 Designation of stud ends and elastomeric seals . 6
8.1 Stud ends . . 6
8.2 Elastomeric seals . 6
9 Identification statement (reference to this document) . 7
Bibliography . 8
iii
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 1179-2:2023
ISO 1179-2:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee
SC 4, Connectors and similar products and components, in collaboration with the European Committee
for Standardization (CEN) Technical Committee CEN/TC 459, ECISS - European Committee for Iron and
Steel Standardization, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 1179-2:2013), which has been technically
revised.
The main changes are as follows:
— Clause 4, Interchangeability warning, concerning the hazards of intermixing of stud ends with
various port types, has been added;
— material requirements for elastomeric seal have been added;
— test methods, test report and re-use of components have been replaced with the equivalent
requirements of ISO 19879;
— Figures 1 and 2 have been redrawn;
— the tables have been renumbered to the order in which they are cited in the text (Table 2 to Table 1,
Table 4 to Table 2, Table 3 remains the same, Table 5 to Table 4, Table 1 to Table 5);
— Annex A and the references to the annex have been deleted;
A list of all parts in the ISO 1179 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 1179-2:2023
ISO 1179-2:2022(E)
Introduction
In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under
pressure within a circuit. In general applications, a fluid can be conveyed under pressure. Components
are connected throu
...
SLOVENSKI STANDARD
oSIST prEN ISO 1179-2:2022
01-april-2022
Priključki za splošno uporabo in za fluidno tehniko - Odprtine in priključki z navoji
po ISO 228-1 z elastomernim ali kovinskim tesnjenjem - 2. del: Zelo obremenjeni
ravni priključki (vrsta S) in malo obremenjeni ravni priključki (vrsta L) z
elastomernim tesnjenjem (tip E) (ISO/DIS 1179-2:2022)
Connections for general use and fluid power - Ports and stud ends with ISO 228-1
threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and
light-duty (L series) stud ends with elastomeric sealing (type E) (ISO/DIS 1179-2:2022)
Leitungsanschlüsse für allgemeine Anwendung und Fluidtechnik – Einschraublöcher und
Einschraubzapfen mit Gewinde nach ISO 228-1 und Elastomerdichtung oder metallener
Dichtkante – Teil 2: Einschraubzapfen mit Elastomerdichtung (Form E), schwere (S) und
leichte Reihe (L) (ISO/DIS 1179-2:2022)
Raccordements pour applications générales et transmissions hydrauliques et
pneumatiques - Orifices et éléments mâles à filetage ISO 228-1 et joint en élastomère ou
étanchéité métal sur métal - Partie 2: Éléments mâles de séries légère (série L) et lourde
(série S) avec joint en élastomère (type E) (ISO/DIS 1179-2:2022)
Ta slovenski standard je istoveten z: prEN ISO 1179-2
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
oSIST prEN ISO 1179-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 1179-2:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 1179-2:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 1179-2
ISO/TC 131/SC 4 Secretariat: ANSI
Voting begins on: Voting terminates on:
2022-02-24 2022-05-19
Connections for general use and fluid power — Ports and
stud ends with ISO 228-1 threads with elastomeric or
metal-to-metal sealing —
Part 2:
Heavy-duty (S series) and light-duty (L series) stud ends
with elastomeric sealing (type E)
Raccordements pour applications générales et transmissions hydrauliques et pneumatiques — Orifices et
éléments mâles à filetage ISO 228-1 et joint en élastomère ou étanchéité métal sur métal —
Partie 2: Éléments mâles de séries légère (série L) et lourde (série S) avec joint en élastomère (type E)
ICS: 23.100.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 1179-2:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 1179-2:2022
ISO/DIS 1179-2:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 1179-2:2022
ISO/DIS 1179-2:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Interchangeability warning .2
5 Dimensions .2
6 Elastomeric seals .2
7 Requirements . 2
7.1 Working pressure . 2
7.2 Performance . 2
8 Designation of stud ends and elastomeric seals . 3
8.1 Stud ends . . 3
8.2 Elastomeric seals . 3
9 Identification statement (reference to this part of ISO 1179) . 3
Bibliography . 8
iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 1179-2:2022
ISO/DIS 1179-2:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 4,
Connectors and similar products and components.
This third edition cancels and replaces the second edition (ISO 1179-2:2013), which has been technically
revised.
ISO 1179 consists of the following parts, under the general title Connections for general use and fluid
power — Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing:
— Part 1: Threaded ports
— Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)
— Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H)
— Part 4: Stud ends for general use only with metal-to-metal sealing (type B)
Changes from previous edition:
— Deleted Annex A and removed references to the Annex.
— Deleted Introduction and incorporated relevant content into Note 2 of Scope
— Added Interchangeability Warning concerning the hazards of intermixing of stud ends with various
port types
— Added material requirements for elastomeric seal
— Replaced Test Methods, Test Report, and Re-Use of Components with the equivalent requirements
of ISO 19879.
— Figures 1 and 2 were redrawn.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 1179-2:2022
DRAFT INTERNATIONAL STANDARD ISO/DIS 1179-2:2022(E)
Connections for general use and fluid power — Ports and
stud ends with ISO 228-1 threads with elastomeric or
metal-to-metal sealing —
Part 2:
Heavy-duty (S series) and light-duty (L series) stud ends
with elastomeric sealing (type E)
1 Scope
This part of ISO 1179 specifies dimensions, performance requirements and test procedures for heavy-
duty (S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing
(type E) that is used with them.
Heavy-duty (S series) stud ends with type E sealing in accordance with this part of ISO 1179 can be
used at working pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing
in accordance with this part of ISO 1179 can be used at working pressures up to 25 MPa (250 bar). The
permissible working pressure depends upon size, materials, design, working conditions, application,
etc.
Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated
performance. It is the responsibility of each manufacturer to perform testing according to the
specification contained in this part of ISO 1179 in order to ensure that components made to this part of
ISO 1179 comply with the performance ratings.
NOTE 1 This part of ISO 1179 applies to connectors detailed in ISO 8434-1, ISO 8434-2, and ISO 8434-6.
NOTE 2 This part of ISO 1179 is not recommended in new designs. For threaded ports and stud ends specified
in new designs in hydraulic fluid power applications the ISO 6149 series should be used. For threaded ports and
stud ends specified in new designs in pneumatic fluid power applications the ISO 16030 should be used, except
where products are to interface with ISO 7-1 threads.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.