SIST ISO 4384-2:2015
Plain bearings - Hardness testing of bearing metals - Part 2: Solid materials
Plain bearings - Hardness testing of bearing metals - Part 2: Solid materials
This International Standard specifies parameters for the hardness testing of solid materials for plain bearings
made from cast and wrought copper and aluminium alloys by machining and forming their wrought products
and ingots, and of tin-based ingots. It represents a supplement to existing International Standards on
hardness testing and, therefore, includes only the extensions and restrictions for observation compared to
those publications.
Owing to the heterogeneous structural composition of the majority of these bearing metals, a Brinell test is
used.
Paliers lisses - Essai de dureté des matériaux antifriction - Partie 2: Matériaux massifs
Drsni ležaji - Preskušanje trdote materialov za ležaje - 2. del: Trdi materiali
Ta mednarodni standard določa parametre za preskušanje trdote trdih materialov za drsne ležaje, izdelane iz litih in gnetenih bakrovih zlitin s strojno obdelavo ter oblikovanjem gnetenih izdelkov in ingotov iz teh materialov, ter iz ingotov na osnovi kositra. Predstavlja dodatek k obstoječim mednarodnim standardom o preskušanju trdote in zato vključuje samo razširitve ter omejitve, ki jih je treba upoštevati v primerjavi s temi objavami.
Zaradi heterogene strukturne sestave večine teh ležajnih kovin se uporablja preskus trdote po Brinellu.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 4384-2:2015
01-marec-2015
1DGRPHãþD
SIST ISO 4384-2:2002
Drsni ležaji - Preskušanje trdote materialov za ležaje - 2. del: Trdi materiali
Plain bearings - Hardness testing of bearing metals - Part 2: Solid materials
Paliers lisses - Essai de dureté des matériaux antifriction - Partie 2: Matériaux massifs
Ta slovenski standard je istoveten z: ISO 4384-2:2011
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 4384-2:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 4384-2:2015
---------------------- Page: 2 ----------------------
SIST ISO 4384-2:2015
INTERNATIONAL ISO
STANDARD 4384-2
Second edition
2011-05-01
Plain bearings — Hardness testing of
bearing metals —
Part 2:
Solid materials
Paliers lisses — Essai de dureté des matériaux antifriction —
Partie 2: Matériaux massifs
Reference number
ISO 4384-2:2011(E)
©
ISO 2011
---------------------- Page: 3 ----------------------
SIST ISO 4384-2:2015
ISO 4384-2:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 4384-2:2015
ISO 4384-2:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4384-2 was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 2,
Materials and lubricants, their properti
...
INTERNATIONAL ISO
STANDARD 4384-2
Second edition
2011-05-01
Plain bearings — Hardness testing of
bearing metals —
Part 2:
Solid materials
Paliers lisses — Essai de dureté des matériaux antifriction —
Partie 2: Matériaux massifs
Reference number
ISO 4384-2:2011(E)
©
ISO 2011
---------------------- Page: 1 ----------------------
ISO 4384-2:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 4384-2:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4384-2 was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 2,
Materials and lubricants, their properties, characteristics, test methods and testing conditions.
This second edition cancels and replaces the first edition (ISO 4384-2:1982), of which it constitutes a minor
revision.
ISO 4384 consists of the following parts, under the general title Plain bearings — Hardness testing of bearing
metals:
⎯ Part 1: Multilayer bearings materials
⎯ Part 2: Solid materials
© ISO 2011 – Al
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.