SIST EN ISO 13002:2000
(Main)Carbon fibre - Designation system for filament yarns (ISO 13002:1998)
Carbon fibre - Designation system for filament yarns (ISO 13002:1998)
1.1 This International Standard establishes a system of designation for filament yarns of carbon fibre which may be used as the basis for specifications.
1.2 This designation system is applicable to filament yarns used for the reinforcement of polymer composites.
It does not apply to discontinuous fibre products pyrolized in the form of staple yarns, woven fabrics, braids, knits,
mats, etc.
1.3 The types of filament yarns are differentiated from each other by a classification system based on appropriate levels of the designatory properties:
a) tensile modulus of elasticity;
b) tensile strength;
c) linear density.
1.4 It is not intended to imply that materials having the same designation give the same performance. This International Standard does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing.
1.5 In order to specify a filament yarn for a particular application or to ensure reproducible processing, additional
requirements may be given in data block 3 (see clause 3).
Kohlenstoffasern - Bezeichnungssystem für Filamentgarne (ISO 13002:1998)
Diese Internationale Norm schafft ein Bezeichnungssystem für Filamentgarne aus Kohlenstoffasern, das als Grundlage für Anforderungen verwendet werden kann. Das Bezeichnungssystem gilt für Filamentgarne, die zur Verstärkung von Polymer-Verbundwerkstoffen verwendet werden. Die Norm gilt nicht für Produkte aus unterbrochenen Fasern, die in Form von Stapelfasergarnen, Geweben, Litzen, Maschenwaren, Matten usw. pyrolysiert wurden.
Fibres de carbone - Systeme de désignation des fils continus (ISO 13002:1998)
1.1 La présente Norme internationale établit un système de désignation des fils continus de carbone, susceptible d'être utilisé comme base pour les spécifications.
1.2 Le présent système de désignation s'applique aux fils continus de carbone utilisés comme renforts dans les composites à matrice polymère.
Il ne s'applique pas aux produits faits de fibres discontinues, pyrolisés sous forme de fils, tissus, tresses, tricots, mats, etc.
1.3 Les types de fils de carbone sont différenciés les uns des autres au moyen d'un système de classement basé sur différents niveaux des propriétés retenues pour la désignation:
a) le module d'élasticité en traction;
b) la résistance en traction;
c) la masse linéique.
1.4 Le fait que des matériaux puissent avoir la même désignation n'impliquent pas qu'ils aient la même performance. La présente Norme internationale ne fournit pas de caractéristiques pour le dimensionnement, de données sur les performances ou de données sur les conditions de fabrication, qui peuvent être nécessaires pour spécifier un matériau pour une application particulière et/ou une méthode de fabrication.
1.5 Pour spécifier un fil de carbone pour une application particulière ou pour assurer une mise en œuvre reproductible, des exigences supplémentaires peuvent être données dans le bloc de données 3 (voir article 3).
Ogljikova vlakna - Sistem označevanja za vlakneno prejo (ISO 13002:1998)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kohlenstoffasern - Bezeichnungssystem für Filamentgarne (ISO 13002:1998)Fibres de carbone - Systeme de désignation des fils continus (ISO 13002:1998)Carbon fibre - Designation system for filament yarns (ISO 13002:1998)59.100.20Ogljikovi materialiCarbon materialsICS:Ta slovenski standard je istoveten z:EN ISO 13002:1998SIST EN ISO 13002:2000en01-maj-2000SIST EN ISO 13002:2000SLOVENSKI
STANDARD
SIST EN ISO 13002:2000
SIST EN ISO 13002:2000
SIST EN ISO 13002:2000
SIST EN ISO 13002:2000
SIST EN ISO 13002:2000
AReference numberISO 13002:1998(E)INTERNATIONALSTANDARDISO13002First edition1998-11-15Carbon fibre — Designation system forfilament yarnsFibres de carbone — Système de désignation des fils continusSIST EN ISO 13002:2000
ISO 13002:1998(E)©
ISO 1998All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronicor mechanical, including photocopying and microfilm, without permission in writing from the publisher.International Organization for StandardizationCase postale 56 · CH-1211 Genève 20 · SwitzerlandInternetiso@iso.chPrinted in SwitzerlandiiForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISOmember bodies). The work of preparing International Standards is normally carried out through ISO technicalcommittees. Each member body interested in a subject for which a technical committee has been established hasthe right to be represented on that committee. International organizations, governmental and non-governmental, inliaison with ISO, also take part in the work. ISO collaborates closely with the International ElectrotechnicalCommission (IEC) on all matters of electrotechnical standardization.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.International Standard ISO 13002 was prepared by Technical Committee ISO/TC 61, Plastics, SubcommitteeSC 13, Composites and reinforcement fibres.SIST EN ISO 13002:2000
INTERNATIONAL STANDARD
© ISOISO 13002:1998(E)1Carbon fibre — Designation system for filament yarns1 Scope1.1
This International Standard establishes a system of designation for filament yarns of carbon fibre which may beused as the basis for specifications.1.2
This designation system is applicable to filament yarns used for the reinforcement of polymer composites.It does not apply to discontinuous fibre products pyrolized in the form of staple yarns, woven fabrics, braids, knits,mats, etc.1.3
The types of filament yarns are differentiated from each other by a classification system based on appropriatelevels of the designatory properties:a) tensile modulus of elasticity;b) tensile strength;c) linear density.1.4
It is not intended to imply that materials having the same designation give the same performance. ThisInternational Standard does not provide engineering data, performance data or data on processing conditions whichmay be required to specify a material for a particular application and/or method of processing.1.5
In order to specify a filament yarn for a particular application or to ensure reproducible processing, additionalrequirements may be given in data block 3 (see clause 3).2 Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of thisInternational Standard. At the time of publication, the editions indicated were valid. All standards are subject torevision, and parties to agreements based on this International Standard are encouraged to investigate thepossibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintainregisters of currently valid International Standards.ISO 1889:1997, Reinforcement yarns — Determination of linear density.ISO 10618:—1), Carbon fibre — Determination of tensile properties of resin-impregnated yarns.
1)
To be published.SIST EN ISO 13002:2000
ISO 13002:1998(E)© ISO23 Designation systemThe designation system for filament yarns is based on the following standardized pattern:DesignationIdentity blockDescriptionInternationalIndividual-item blockblock(optional)Standardnumber blockDatablockDatablockDatablock123The designation consists of an optional description block, reading “Reinforcing fibre”, and an identity blockcomprising the International Standard number and an individual-item block. For unambiguous designation, theindividual-item block is subdivided into three data blocks comprising the following information:¾ Data block 1: Identification of the ca
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.