SIST ISO 18400-101:2018
Soil quality - Sampling - Part 101: Framework for the preparation and application of a sampling plan
Soil quality - Sampling - Part 101: Framework for the preparation and application of a sampling plan
ISO 18400-101:2017 specifies the procedural elements to be taken in the preparation and application of a sampling plan. The sampling plan describes among other things what laboratory samples are to be taken, how they are to be taken and from where they are to be taken, in order that the objectives of the investigation programme can be achieved. The principles or basic rules outlined in this document provide a framework that can be used to
- produce standardized sampling plans for use in more regular or routine circumstances,
- incorporate the specific requirements of national legislation, and
- design and develop a sampling plan for use on a case-by-case basis.
ISO 18400-101:2017 is applicable to sampling of soil and soil material, more specifically, e.g.
- soil in the landscape,
- soil stockpiles,
- potentially contaminated sites,
- agricultural soils,
- landfills, and
- forest soils.
Ultimately, the sampling plan provides the sampler with detailed instructions on how sampling should be carried out.
NOTE 1 There might be a need for more than one sampling plan to meet all the requirements of the investigation programme.
NOTE 2 It might sometimes be appropriate to divide a site or above-ground deposit (e.g. stockpile) into two or more zones and to develop separate sampling plans for each zone. For example, a (potentially) contaminated site might be zoned on the basis of past use, future use, topography or geology and an agricultural site on the basis of known or suspected soil types or use (pasture, type of crops, etc.).
Qualité du sol - Échantillonnage - Partie 101: Cadre pour la préparation et l'application d'un plan d'échantillonnage
ISO 18400-101:2017 spécifie les éléments procéduraux qui doivent être suivis lors de la préparation et de l'application d'un plan d'échantillonnage. Le plan d'échantillonnage décrit entre autres les échantillons pour laboratoire à prélever, la façon de les prélever et l'endroit où les prélever, afin de pouvoir atteindre les objectifs du programme d'investigation. Les principes ou les règles de base énoncés dans le présent document fournissent un cadre pouvant être utilisé pour:
- produire des plans d'échantillonnage normalisés destinés à être utilisés dans des circonstances plus régulières ou de routine;
- incorporer les exigences spécifiques de la législation nationale; et
- concevoir et élaborer un plan d'échantillonnage au cas par cas.
ISO 18400-101:2017 est applicable à l'échantillonnage des sols et des matériaux du sol, notamment par exemple:
- sols dans le paysage;
- dépôts en tas de matériaux de sol;
- sites potentiellement pollués;
- sols agricoles;
- décharges; et
- sols forestiers.
Enfin, le plan d'échantillonnage fournit à l'échantillonneur des instructions détaillées sur la manière dont il convient d'effectuer l'échantillonnage.
Kakovost tal - Vzorčenje - 101. del: Okvirno navodilo za pripravo in uporabo načrta vzorčenja
Ta dokument določa postopkovne elemente, ki jih je treba upoštevati pri pripravi in izvajanju načrta vzorčenja. Načrt vzorčenja med drugim opisuje, katere laboratorijske vzorce je treba odvzeti ter kako in na katerih mestih je treba odvzeti laboratorijske vzorce, da se zagotovi doseganje ciljev preiskovalnega programa. Načela osnovnih pravil, ki so opredeljena v tem dokumentu, zagotavljajo okvir, ki se lahko uporablja za:
– izdelavo standardiziranih načrtov vzorčenja za uporabo v rednih ali rutinskih okoliščinah,
– vključitev posebnih zahtev nacionalne zakonodaje in
– oblikovanje in razvoj načrta vzorčenja, ki se uporablja za vsak primer posebej.
Ta dokument se uporablja za vzorčenje prsti in zemeljskega materiala, in sicer npr. za:
– prsti v pokrajinah,
– nasutja prsti,
– potencialno onesnažena območja,
– kmetijska tla,
– odlagališča in
– gozdna tla.
Načrt vzorčenja vključuje tudi vzorčevalnik in podrobna navodila za izvajanje
vzorčenja.
OPOMBA 1: za izpolnjevanje vseh zahtev preiskovalnega programa je lahko potrebnih več
načrtov vzorčenja.
OPOMBA 2: včasih je lahko primerno, da se mesto odvzema ali nadzemno odlagališče (npr. nasutje) razdeli na dve ali več območij in pripravi ločen načrt vzorčenja za vsako območje posebej. (Potencialno) onesnaženo območje se lahko na primer določi na podlagi pretekle uporabe, prihodnje uporabe, topografije ali geologije, kmetijsko območje pa na podlagi znanih ali predvidenih vrst prsti ali na podlagi uporabe (pašniki, vrste pridelkov itd.).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2018
.DNRYRVWWDO9]RUþHQMHGHO2NYLUQRQDYRGLOR]DSULSUDYRLQXSRUDERQDþUWD
Y]RUþHQMD
Soil quality - Sampling - Part 101: Framework for the preparation and application of a
sampling plan
Qualité du sol - Échantillonnage - Partie 101: Cadre pour la préparation et l'application
d'un plan d'échantillonnage
Ta slovenski standard je istoveten z: ISO 18400-101:2017
ICS:
13.080.05 Preiskava tal na splošno Examination of soils in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 18400-101
First edition
2017-01
Soil quality — Sampling —
Part 101:
Framework for the preparation and
application of a sampling plan
Qualité du sol — Échantillonnage —
Partie 101: Cadre pour la préparation et l’application d’un plan
d’échantillonnage
Reference number
©
ISO 2017
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of a sampling plan . 2
4.1 Principle . 2
4.2 Key elements of a sampling plan . 4
4.2.1 Quality assurance (QA) and quality control (QC) . 4
4.2.2 Involved parties . 4
4.2.3 Objectives of the investigation programme . 4
4.2.4 Investigation phase . 5
4.2.5 Background information . 5
4.2.6 Identify constituents to be tested and test method to be applied . 6
4.2.7 Health and safety . 7
4.2.8 Defining the sampling approach . 7
4.2.9 Identify sampling technique . 8
5 Sampling . 9
5.1 Taking the samples . 9
5.2 Delivery . 9
6 Reporting .10
6.1 Documenting the sampling plan .10
6.2 Sampling record and report.10
Annex A (informative) Checklist for the items to be addressed in a sampling plan .11
Bibliography .13
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html
This document was prepared by Technical Committee ISO/TC 190, Soil Quality, Subcommittee SC 2,
Sampling.
This first edition of ISO 18400-101, together with ISO 18400-104 and ISO 18400-107, cancels and
replaces ISO 10381-1:2002, which has been technically and structurally revised. The ISO 18400 series
is based on a modular structure and cannot be compared to ISO 10381-1 clause by clause.
A list of all parts in the ISO 18400 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
Introduction
The characterization of soils and soil materials within the scope of this document, in terms of their
potential environmental impact, or suitability for a particular use, requires a variety of tests to be
performed. These tests may relate to the chemical, physical and biological properties of the soil or
soil material. Validity of these tests requires performance on a representative sample or a number of
representative samples.
The potential scope of an investigation programme can be complex; the process flowchart in Figure 1
defines seven key elements that make up the essential elements of the investigation programme. The
principles outlined in this document provide a framework that can be used to design and develop a
sampling plan, which is the first of the seven key elements. Other International Standards provide
detailed instructions on how to complete the remaining key elements.
Before any investigation programme is devised, it is important that the objectives be first established
since they are the major determining factors for the actual sampling, e.g. the position, density and depth
of sampling points, time of sampling, sampling procedures, the acceptable levels of sampling uncertainty
and the subsequent treatment of samples and analytical requirements. The details of an investigation
programme depend on whether the information needed is the average value, the distribution, or the
variability of given soil parameters.
The degree of detail and measurement uncertainty required and also to the manner in which the results
are to be expressed and presented, for example, concentration of constituents, maximum and minimum
values, arithmetic means, median values, etc. needs some considerations. Additionally, it is advisable to
compile a list of constituents of interest and the relevant analytical procedures consulted, since these
will usually give guidance on precautions to be observed during sampling and subsequent handling
of soil samples. The investigation programme design often involves iterative discussion between the
involved parties.
Given that complexity, a sampling plan is defined by the specific objectives of the investigation
programme and how those objectives can be practically achieved with reference specifically to the
sampling activities for the situation under investigation. The sampling plan provides simple and
unambiguous instructions for the sampler, and as a consequence sampling is to be performed only
when an approved sampling plan is available.
A large variety of sampling objectives exist, including the following:
— sampling of ex-situ soil (e.g. soil stockpiles) in order to estimate the (average) concentration of
constituents in a specified quantity of soil material;
— sampling of agricultural, natural and near natural soils in the landscape in order to estimate the
(average) concentration of constituents over a specified soil area and depth;
— sampling to determine chemical, physical or biological characteristics of the soil material;
— sampling of (potentially) contaminated sites in order to characterize and delineate the contamination
and to estimate the risks for human health and the environment.
1)
ISO 18400-104 requires that a preliminary (phase 1) investigation comprising a desk study and a site
reconnaissance is carried out before any sampling or other intrusive activities are carried out. The
extent of the preliminary investigation will depend on the objectives of the overall investigation and
1)
the on-site activities expected will be required (see ISO 18400-202 .
It will often be necessary to carry out an exploratory (phase 2) investigation as described in
1)
ISO 18400-104 before the final objectives for the detailed (phase 3) investigation can be defined.
It is important to take into account all relevant data from previous investigation programmes at the
same or similar locations and other information on local conditions. Previous personal experience can
1) Under preparation.
also be very valuable. Time and money allocated to the design of a proper investigation programme
is usually well justified because it ensures that the required information is obtained efficiently and
economically.
In addition to the design and development of a sampling plan, this document deals with the actual
sampling in accordance with that sampling plan and it deals with the development of the sampling
report. A sampling plan shows details of all the information pertinent to a particular sampling exercise.
The procedural elements that will be considered to complete key element 1 ‘The preparation and
application of a sampling plan’ are detailed in Figure 2. It is this process map that provides the basic
framework for the practitioner developing a sampling plan to meet the requirements of any investigation
programme. This document can be used to
— produce standardized sampling plans for use in more routine circumstances,
— incorporate the specific requirements of national legislation, and
— design and develop a sampling plan for use on a case-by-case basis.
This document is part of a series on sampling standards for soil. The role/position of the International
Standards within the total investigation programme is shown in Figure 1.
Essential information for the application of this document and reference to all International Standards
belonging to the ISO 18400 series is provided in
...
INTERNATIONAL ISO
STANDARD 18400-101
First edition
2017-01
Soil quality — Sampling —
Part 101:
Framework for the preparation and
application of a sampling plan
Qualité du sol — Échantillonnage —
Partie 101: Cadre pour la préparation et l’application d’un plan
d’échantillonnage
Reference number
©
ISO 2017
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of a sampling plan . 2
4.1 Principle . 2
4.2 Key elements of a sampling plan . 4
4.2.1 Quality assurance (QA) and quality control (QC) . 4
4.2.2 Involved parties . 4
4.2.3 Objectives of the investigation programme . 4
4.2.4 Investigation phase . 5
4.2.5 Background information . 5
4.2.6 Identify constituents to be tested and test method to be applied . 6
4.2.7 Health and safety . 7
4.2.8 Defining the sampling approach . 7
4.2.9 Identify sampling technique . 8
5 Sampling . 9
5.1 Taking the samples . 9
5.2 Delivery . 9
6 Reporting .10
6.1 Documenting the sampling plan .10
6.2 Sampling record and report.10
Annex A (informative) Checklist for the items to be addressed in a sampling plan .11
Bibliography .13
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html
This document was prepared by Technical Committee ISO/TC 190, Soil Quality, Subcommittee SC 2,
Sampling.
This first edition of ISO 18400-101, together with ISO 18400-104 and ISO 18400-107, cancels and
replaces ISO 10381-1:2002, which has been technically and structurally revised. The ISO 18400 series
is based on a modular structure and cannot be compared to ISO 10381-1 clause by clause.
A list of all parts in the ISO 18400 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
Introduction
The characterization of soils and soil materials within the scope of this document, in terms of their
potential environmental impact, or suitability for a particular use, requires a variety of tests to be
performed. These tests may relate to the chemical, physical and biological properties of the soil or
soil material. Validity of these tests requires performance on a representative sample or a number of
representative samples.
The potential scope of an investigation programme can be complex; the process flowchart in Figure 1
defines seven key elements that make up the essential elements of the investigation programme. The
principles outlined in this document provide a framework that can be used to design and develop a
sampling plan, which is the first of the seven key elements. Other International Standards provide
detailed instructions on how to complete the remaining key elements.
Before any investigation programme is devised, it is important that the objectives be first established
since they are the major determining factors for the actual sampling, e.g. the position, density and depth
of sampling points, time of sampling, sampling procedures, the acceptable levels of sampling uncertainty
and the subsequent treatment of samples and analytical requirements. The details of an investigation
programme depend on whether the information needed is the average value, the distribution, or the
variability of given soil parameters.
The degree of detail and measurement uncertainty required and also to the manner in which the results
are to be expressed and presented, for example, concentration of constituents, maximum and minimum
values, arithmetic means, median values, etc. needs some considerations. Additionally, it is advisable to
compile a list of constituents of interest and the relevant analytical procedures consulted, since these
will usually give guidance on precautions to be observed during sampling and subsequent handling
of soil samples. The investigation programme design often involves iterative discussion between the
involved parties.
Given that complexity, a sampling plan is defined by the specific objectives of the investigation
programme and how those objectives can be practically achieved with reference specifically to the
sampling activities for the situation under investigation. The sampling plan provides simple and
unambiguous instructions for the sampler, and as a consequence sampling is to be performed only
when an approved sampling plan is available.
A large variety of sampling objectives exist, including the following:
— sampling of ex-situ soil (e.g. soil stockpiles) in order to estimate the (average) concentration of
constituents in a specified quantity of soil material;
— sampling of agricultural, natural and near natural soils in the landscape in order to estimate the
(average) concentration of constituents over a specified soil area and depth;
— sampling to determine chemical, physical or biological characteristics of the soil material;
— sampling of (potentially) contaminated sites in order to characterize and delineate the contamination
and to estimate the risks for human health and the environment.
1)
ISO 18400-104 requires that a preliminary (phase 1) investigation comprising a desk study and a site
reconnaissance is carried out before any sampling or other intrusive activities are carried out. The
extent of the preliminary investigation will depend on the objectives of the overall investigation and
1)
the on-site activities expected will be required (see ISO 18400-202 .
It will often be necessary to carry out an exploratory (phase 2) investigation as described in
1)
ISO 18400-104 before the final objectives for the detailed (phase 3) investigation can be defined.
It is important to take into account all relevant data from previous investigation programmes at the
same or similar locations and other information on local conditions. Previous personal experience can
1) Under preparation.
also be very valuable. Time and money allocated to the design of a proper investigation programme
is usually well justified because it ensures that the required information is obtained efficiently and
economically.
In addition to the design and development of a sampling plan, this document deals with the actual
sampling in accordance with that sampling plan and it deals with the development of the sampling
report. A sampling plan shows details of all the information pertinent to a particular sampling exercise.
The procedural elements that will be considered to complete key element 1 ‘The preparation and
application of a sampling plan’ are detailed in Figure 2. It is this process map that provides the basic
framework for the practitioner developing a sampling plan to meet the requirements of any investigation
programme. This document can be used to
— produce standardized sampling plans for use in more routine circumstances,
— incorporate the specific requirements of national legislation, and
— design and develop a sampling plan for use on a case-by-case basis.
This document is part of a series on sampling standards for soil. The role/position of the International
Standards within the total investigation programme is shown in Figure 1.
Essential information for the application of this document and reference to all International Standards
belonging to the ISO 18400 series is provided in ISO 18400-100. ISO 18400-100 will be updated on a
regular basis as long as the International Standards of this series are under development.
vi © ISO 2017 – All rights reserved
Figure 1 — Links between the essential elements of an investigation programme
NOTE 1 Numbers in circles define the key elements (1 to 7) of the investigation programme.
NOTE 2 Figure 1 displays a generic process which can be amended when necessary.
INTERNATIONAL STANDARD ISO 18400-101:2017(E)
Soil quality — Sampling —
Part 101:
Framework for the preparation and application of a
sampling plan
1 Scope
This document specifies the procedural elements to be taken in the preparation and application of a
sampling plan. The sampling plan describes among other things what labo
...
NORME ISO
INTERNATIONALE 18400-101
Première édition
2017-01
Qualité du sol — Échantillonnage —
Partie 101:
Cadre pour la préparation
et l’application d’un plan
d’échantillonnage
Soil quality — Sampling —
Part 101: Framework for the preparation and application of a
sampling plan
Numéro de référence
©
ISO 2017
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – Tous droits réservés
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Préparation d’un plan d’échantillonnage . 2
4.1 Principe . 2
4.2 Éléments clés d’un plan d’échantillonnage . 5
4.2.1 Assurance qualité (AQ) et contrôle qualité (CQ) . 5
4.2.2 Parties concernées . 5
4.2.3 Objectifs du programme d’investigation . 5
4.2.4 Phase d’investigation . 6
4.2.5 Informations de base. 7
4.2.6 Identification des constituants à analyser et de la méthode d’essai à appliquer . 8
4.2.7 Santé et sécurité . 8
4.2.8 Définition de l’approche d’échantillonnage . 8
4.2.9 Identification d’une technique d’échantillonnage .10
5 Échantillonnage .10
5.1 Prélèvement des échantillons .10
5.2 Livraison .11
6 Notification .11
6.1 Documentation du plan d’échantillonnage.11
6.2 Enregistrement et rapport d’échantillonnage .11
Annexe A (informative) Liste de contrôle des éléments devant être abordés dans un
plan d’échantillonnage .12
Bibliographie .14
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion
de l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC) voir le lien suivant: w w w . i s o .org/ iso/ fr/ foreword .html.
Le présent document a été élaboré par le comité technique ISO/TC 190, Qualité du sol, sous-comité SC 2,
Échantillonnage.
Cette première édition de l’ISO 18400-101, conjointement avec l’ISO 18400-104 et l’ISO 18400-107,
annule et remplace l’ISO 10381-1:2002 qui a fait l’objet d’une révision technique et structurelle. La
série ISO 18400 est fondée sur une structure modulaire et ne peut être comparée, article par article, à
l’ISO 10381-1.
Une liste de toutes les parties de la série ISO 18400 peut être consultée sur le site de l’ISO.
iv © ISO 2017 – Tous droits réservés
Introduction
La caractérisation des sols et des matériaux du sol relevant du domaine d’application du présent
document, en fonction de leur impact potentiel sur l’environnement, ou de leur aptitude à un usage
particulier, nécessite la réalisation de divers essais. Ces essais peuvent se rapporter aux propriétés
chimiques, physiques ou biologiques du sol ou des matériaux du sol. La validité de ces essais nécessite
leur réalisation sur un échantillon représentatif ou sur un certain nombre d’échantillons représentatifs.
L’objectif d’un programme d’investigation peut être potentiellement complexe; l’organigramme
présenté à la Figure 1 définit sept éléments clés qui constituent les éléments essentiels du programme
d’investigation. Les principes énoncés dans le présent document fournissent un cadre pouvant servir
à la conception et à la mise en place d’un plan d’échantillonnage, qui constitue le premier des sept
éléments clés. D’autres Normes internationales fournissent des instructions détaillées sur la façon dont
les autres éléments clés doivent être réalisés.
Avant l’élaboration d’un programme d’investigation, il est important que les objectifs soient d’abord
définis car ils constituent les facteurs déterminants majeurs pour l’échantillonnage effectif, par exemple
la position, la densité et la profondeur des points d’échantillonnage, la période de l’échantillonnage, les
procédures d’échantillonnage, les niveaux acceptables d’incertitude d’échantillonnage, le traitement
ultérieur des échantillons et les exigences relatives aux analyses. Les détails d’un programme
d’investigation dépendent des informations que l’on souhaite obtenir, c’est-à-dire la valeur moyenne, la
distribution ou la variabilité de paramètres particuliers du sol.
Le niveau de détail et l’incertitude de mesure exigée, ainsi que la manière dont les résultats doivent être
exprimés et présentés, par exemple sous forme de concentrations de constituants, de valeurs maximales
et minimales, de moyennes arithmétiques, de valeurs médianes, etc., doivent être pris en considération.
De plus, il est conseillé d’établir une liste des constituants présentant un intérêt et de consulter les
modes opératoires d’analyse appropriés car ils donnent habituellement des recommandations sur les
précautions à prendre lors de l’échantillonnage et de la manipulation ultérieure des échantillons de sol.
La conception du programme d’investigation implique souvent des échanges itératifs entre les parties
concernées.
Compte tenu de cette complexité, un plan d’échantillonnage est défini par les objectifs spécifiques
du programme d’investigation et par la manière dont ces objectifs peuvent être concrètement
atteints avec une référence spécifique aux activités d’échantillonnage pour la situation faisant l’objet
de l’investigation. Le plan d’échantillonnage fournit des instructions simples et sans ambiguïté à
l’échantillonneur; de ce fait l’échantillonnage ne doit être effectué que lorsqu’un plan d’échantillonnage
approuvé est disponible.
Il existe une grande variété d’objectifs d’échantillonnage, parmi lesquels:
— échantillonnage d’un sol ex-situ (par exemple dépôts en tas de matériaux du sol) afin d’estimer la
concentration (moyenne) des constituants dans une quantité spécifiée de matériaux du sol;
— échantillonnage de terres agricoles, de sols naturels et quasi naturels dans le paysage afin d’estimer
la concentration (moyenne) des constituants sur une surface et une profondeur spécifiées du sol;
— échantillonnage pour déterminer les caractéristiques chimiques, physiques et biologiques des
matériaux du sol;
— échantillonnage de sites (potentiellement) pollués afin de caractériser et de délimiter la pollution et
d’estimer les risques pour la santé humaine et pour l’environnement.
1)
L’ISO 18400-104 exige d’effectuer une investigation préliminaire (phase 1) comprenant une étude sur
documents et une reconnaissance du site, avant d’entreprendre tout échantillonnage ou autres activités
intrusives. L’étendue de l’investigation préliminaire dépendra des objectifs de l’investigation globale et
1)
des activités sur site qu’il est prévu de réaliser (voir l’ISO 18400-202 ).
1) En cours d’élaboration.
Il sera souvent nécessaire de procéder à une investigation exploratoire (phase 2), telle que décrite dans
1)
l’ISO 18400-104 , avant de pouvoir définir les objectifs finaux de l’investigation détaillée (phase 3).
Il est important de prendre en considération toutes les données appropriées issues des programmes
d’investigation précédents au même endroit ou à des endroits similaires, ainsi que d’autres informations
concernant les conditions locales. Une expérience personnelle antérieure peut également être très
intéressante. Le temps et l’argent alloués à la conception d’un programme d’investigation correct sont
habituellement bien justifiés parce qu’ils garantissent que les informations requises sont obtenues de
manière efficace et économique.
Outre la conception et l’élaboration d’un plan d’échantillonnage, le présent document traite de
l’échantillonnage réel conformément à ce plan d’échantillonnage, ainsi que de l’établissement du rapport
d’échantillonnage. Il convient qu’un plan d’échantillonnage décrive en détail toutes les informations
pertinentes se rapportant à une activité d’échantillonnage particulière.
Les éléments procéduraux qui seront pris en compte pour réaliser l’élément clé 1 «Préparation et
application d’un plan d’échantillonnage» sont détaillées à la Figure 2. Cette cartographie de processus
fournit le cadre de base permettant au concepteur d’élaborer un plan d’échantillonnage conforme aux
exigences d’un programme d’investigation. Le présent document peut être utilisé pour
— produire des plans d’échantillonnage normalisés destinés à être utilisés dans des circonstances
plus courantes,
— inco
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.