SIST EN 302 617-2 V1.1.1:2010
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
- Abstract
The present document applies to DSB AM ground base stations, with channel separations of 25 kHz intended for analogue speech. The scope of the present document is limited to ground based transmitters, receivers and transceivers. These radio equipment types are capable of operating in all or any part of the aeronautical frequency band between 225 MHz and 399,975 MHz. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2, which states that "... radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive as well as essential requirements under the Single European Sky
Interoperability Regulation (as amended) [i.3] and related implementing rules may apply to equipment within the scope of the present document.
- Status
- Published
- Publication Date
- 08-Nov-2010
- Technical Committee
- MOC - Mobile Communications
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 03-Nov-2010
- Due Date
- 08-Jan-2011
- Completion Date
- 09-Nov-2010
- Mandate
- M/405
Buy Documents
en_30261702v010101p - Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 302 617-2 V1.1.1 (2010-06) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
SIST EN 302 617-2 V1.1.1:2010 is a Harmonized European Standard for ground-based UHF radio transmitters, receivers and transceivers used in the UHF aeronautical mobile service with amplitude modulation. It specifies the technical requirements and test provisions used to show conformity with article 3.2 of the R&TTE Directive, for DSB AM ground base stations with 25 kHz channel separation intended for analogue speech. In practice, it is used to assess spectrum use, transmitter performance and receiver selectivity for fixed aeronautical ground stations.
What does SIST EN 302 617-2 V1.1.1:2010 specify?
SIST EN 302 617-2 V1.1.1:2010 applies to ground-based transmitters, receivers and transceivers operating in the aeronautical frequency band from 225 MHz to 399,975 MHz. The document is focused on article 3.2 of Directive 1999/5/EC, which is about effective spectrum use and avoiding harmful interference.
The standard is organized into five clauses and three annexes.
| Part | What it covers |
|---|---|
| Clause 1 | Scope |
| Clause 2 | References |
| Clause 3 | Definitions and abbreviations |
| Clause 4 | Technical requirements specifications |
| Clause 5 | Testing for compliance with technical requirements |
| Annex A | HS Requirements and conformance Test specifications Table (HS-RTT) |
| Annex B | EN title in the official languages |
| Annex C | Bibliography |
Annex A is the key compliance map: it links each requirement to its test specification and marks the tests as essential for presumption of conformity.
What are the key requirements of SIST EN 302 617-2 V1.1.1:2010?
SIST EN 302 617-2 V1.1.1:2010 requires equipment to meet its technical limits within the declared operational environmental profile. That means the supplier must state the operating environment, and the equipment has to comply throughout that declared range.
Transmitter performance
Clause 4.2.1 covers transmitter requirements such as frequency error, carrier power, adjacent channel power, conducted spurious emissions, intermodulation attenuation, keying transient frequency behaviour and cabinet radiation. These checks matter because they show whether the transmitter stays on frequency, radiates the intended power and keeps unwanted emissions low enough to protect nearby channels.
The transmitter limits and test methods are taken from EN 302 617-1, except for cabinet radiation, which refers to EN 300 113-1. In practice, this lets a test house reuse common measurement methods while checking the specific aeronautical radio parameters required here.
Receiver performance
Clause 4.2.2 covers sensitivity, adjacent channel rejection, spurious response rejection, intermodulation response rejection, blocking or desensitisation, conducted spurious emissions, cross modulation rejection and cabinet radiation. The standard notes that these receiver aspects are essential for immediate and successful ground-to-air communication.
For users, this means the receiver must keep working when other signals are present nearby. Poor receiver performance can force retransmissions, which wastes spectrum and can disrupt aeronautical communications.
Test conditions and uncertainty
Clause 5 says tests shall be carried out at representative points within the declared environmental profile, using the procedures in EN 302 617-1 and, for cabinet radiation, EN 300 113-1. This makes the test reflect the way the equipment is actually intended to operate.
Clause 5.2 requires measurement uncertainty to be reported and controlled according to TR 100 028. The standard also ties the uncertainty figures to the confidence level used for the measurements, so test reports can be judged consistently.
Compliance mapping
Annex A lists 15 requirements and their corresponding test specifications in the HS-RTT table. All listed requirements are marked as essential, so a successful test programme has to cover the essential radio test suite to support presumption of conformity.
What terms does SIST EN 302 617-2 V1.1.1:2010 define?
- Aeronautical mobile service - A mobile service between aeronautical stations and aircraft stations, with survival craft stations also able to participate.
- Ground base station - Aeronautical station equipment for use with an external antenna and intended for a fixed location.
- Conducted measurements - Measurements made through a direct RF connection to the equipment under test.
- Radiated measurements - Measurements based on the radiated field from the equipment.
- Environmental profile - The range of environmental conditions within which the equipment must meet the standard.
- AM (Amplitude Modulation) - The modulation method used by the equipment covered by this standard.
- DSB (Double Side Band) - The AM mode named in the scope for the ground base stations.
- RF (Radio Frequency) - The frequency domain used for the direct and radiated measurements.
Who uses SIST EN 302 617-2 V1.1.1:2010?
Manufacturers of aeronautical ground radio equipment use this standard when designing and declaring compliance for transmitters, receivers and transceivers. Test laboratories use it to run the transmitter and receiver test suites and to prepare compliance reports.
Quality managers, conformity assessment teams and buyers use it to check whether a product is aimed at fixed UHF aeronautical voice communications in the 225 MHz to 399,975 MHz band. Regulators and spectrum specialists use it when assessing article 3.2 conformity for equipment intended for ground-to-air communications.
Which standards are used with SIST EN 302 617-2 V1.1.1:2010?
- ETSI EN 302 617-1 (V1.1.1) - Provides the technical characteristics, definitions and measurement methods reused throughout this part, including the transmitter and receiver test procedures.
- ETSI EN 300 113-1 (V1.6.2) - Supplies the cabinet radiation limits and the related test procedures referenced for both transmitter and receiver cabinet radiation.
- ETSI TR 100 028 (all parts) - Gives the method used to calculate and report measurement uncertainty.
- ETSI EG 201 399 - Explains the modular structure used for Harmonized Standards under the R&TTE Directive.
What does the SIST EN 302 617-2 V1.1.1:2010 document contain?
The document contains the scope, reference documents, definitions and abbreviations, followed by the technical requirements for transmitters and receivers. Clause 5 gives the compliance test approach, including environmental conditions, interpretation of measurement results and the essential radio test suites.
It also includes Table 1 for measurement uncertainty limits and Annex A’s HS-RTT mapping of requirements to test specifications. Annex B provides the title in official languages, and Annex C gives the bibliography.
Buy Documents
en_30261702v010101p - Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 302 617-2 V1.1.1 (2010-06) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
SIST EN 302 617-2 V1.1.1:2010 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Electromagnetic compatibility and Radio spectrum Matters (ERM) - Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive". This standard covers: The present document applies to DSB AM ground base stations, with channel separations of 25 kHz intended for analogue speech. The scope of the present document is limited to ground based transmitters, receivers and transceivers. These radio equipment types are capable of operating in all or any part of the aeronautical frequency band between 225 MHz and 399,975 MHz. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2, which states that "... radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive as well as essential requirements under the Single European Sky Interoperability Regulation (as amended) [i.3] and related implementing rules may apply to equipment within the scope of the present document.
The present document applies to DSB AM ground base stations, with channel separations of 25 kHz intended for analogue speech. The scope of the present document is limited to ground based transmitters, receivers and transceivers. These radio equipment types are capable of operating in all or any part of the aeronautical frequency band between 225 MHz and 399,975 MHz. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2, which states that "... radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive as well as essential requirements under the Single European Sky Interoperability Regulation (as amended) [i.3] and related implementing rules may apply to equipment within the scope of the present document.
SIST EN 302 617-2 V1.1.1:2010 is classified under the following ICS (International Classification for Standards) categories: 33.060.20 - Receiving and transmitting equipment; 33.100.01 - Electromagnetic compatibility in general. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 302 617-2 V1.1.1:2010 is associated with the following European legislation: EU Directives/Regulations: 1999/5/EC, TRRTP124; Standardization Mandates: M/405. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 302 617-2 V1.1.1:2010 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Ground-based UHF radio transmitters,
receivers and transceivers for the UHF
aeronautical mobile service using amplitude modulation;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
2 ETSI EN 302 617-2 V1.1.1 (2010-10)
Reference
DEN/ERM-JTFEA-002-2
Keywords
aeronautical, AM, DSB, radio, testing, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 302 617-2 V1.1.1 (2010-10)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Technical requirements specifications . 7
4.1 Environmental profile . 7
4.2 Conformance requirements . 8
4.2.1 Transmitter requirements . 8
4.2.1.1 Frequency error . 8
4.2.1.2 Carrier power (conducted) . 8
4.2.1.3 Adjacent channel power . 8
4.2.1.4 Conducted spurious emissions . 8
4.2.1.5 Intermodulation attenuation . 8
4.2.1.6 Keying transient frequency behaviour . 8
4.2.1.7 Cabinet Radiation . 8
4.2.2 Receiver requirements . 8
4.2.2.1 Sensitivity . 8
4.2.2.2 Adjacent channel rejection . 8
4.2.2.3 Spurious response rejection . 9
4.2.2.4 Intermodulation response rejection . 9
4.2.2.5 Blocking or desensitisation . 9
4.2.2.6 Conducted spurious emissions . 9
4.2.2.7 Cross modulation rejection . 9
4.2.2.8 Cabinet radiation . 9
5 Testing for compliance with technical requirements . 9
5.1 Environmental conditions for testing . 9
5.2 Interpretation of the measurement results . 9
5.3 Essential radio test suites . 10
5.3.1 Transmitter test specifications . 10
5.3.1.1 Frequency error . 10
5.3.1.2 Carrier power (conducted) . 10
5.3.1.3 Adjacent channel power . 10
5.3.1.4 Conducted spurious emissions . 10
5.3.1.5 Intermodulation attenuation . 10
5.3.1.6 Keying transient frequency behaviour . 10
5.3.1.7 Cabinet Radiation . 11
5.3.2 Receiver test specifications . 11
5.3.2.1 Sensitivity . 11
5.3.2.2 Adjacent channel rejection . 11
5.3.2.3 Spurious response rejection . 11
5.3.2.4 Intermodulation response rejection . 11
5.3.2.5 Blocking or desensitisation . 11
5.3.2.6 Conducted spurious emissions . 11
5.3.2.7 Cross modulation rejection . 11
5.3.2.8 Cabinet Radiation . 11
ETSI
4 ETSI EN 302 617-2 V1.1.1 (2010-10)
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 12
Annex B (informative): The EN title in the official languages . 14
Annex C (informative): Bibliography . 15
History . 16
ETSI
5 ETSI EN 302 617-2 V1.1.1 (2010-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.5] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering Ground-based UHF radio transmitters, receivers and
transceivers for the UHF aeronautical mobile service using amplitude modulation, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 20 October 2010
Date of latest announcement of this EN (doa): 31 January 2011
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 July 2011
Date of withdrawal of any conflicting National Standard (dow): 31 July 2012
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.4].
ETSI
6 ETSI EN 302 617-2 V1.1.1 (2010-10)
1 Scope
The present document applies to DSB AM ground base stations, with channel separations of 25 kHz intended for
analogue speech. The scope of the present document is limited to ground based transmitters, receivers and transceivers.
These radio equipment types are capable of operating in all or any part of the aeronautical frequency band between
225 MHz and 399,975 MHz.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2,
which states that ". radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive as well as essential requirements under the Single European Sky
Interoperability Regulation (as amended) [i.3] and related implementing rules may apply to equipment within the scope
of the present document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references,only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 302 617-1 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile
service using amplitude modulation; Part 1: Technical characteristics and methods of
measurement".
[2] ETSI EN 300 113-1 (V1.6.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using
constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical
characteristics and methods of measurement".
2.2 Informative references
The following referenced documents are n
...
Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Ground-based UHF radio
transmitters, receivers and transceivers for the UHF
aeronautical mobile service using amplitude modulation;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
2 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Reference
DEN/ERM-JTFEA-002-2
Keywords
aeronautical, AM, DSB, radio, testing, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Technical requirements specifications . 7
4.1 Environmental profile . 7
4.2 Conformance requirements . 8
4.2.1 Transmitter requirements . 8
4.2.1.1 Frequency error . 8
4.2.1.2 Carrier power (conducted) . 8
4.2.1.3 Adjacent channel power . 8
4.2.1.4 Conducted spurious emissions . 8
4.2.1.5 Intermodulation attenuation . 8
4.2.1.6 Keying transient frequency behaviour . 8
4.2.1.7 Cabinet Radiation . 8
4.2.2 Receiver requirements . 8
4.2.2.1 Sensitivity . 8
4.2.2.2 Adjacent channel rejection . 8
4.2.2.3 Spurious response rejection . 9
4.2.2.4 Intermodulation response rejection . 9
4.2.2.5 Blocking or desensitisation . 9
4.2.2.6 Conducted spurious emissions . 9
4.2.2.7 Cross modulation rejection . 9
4.2.2.8 Cabinet radiation . 9
5 Testing for compliance with technical requirements . 9
5.1 Environmental conditions for testing . 9
5.2 Interpretation of the measurement results . 9
5.3 Essential radio test suites . 10
5.3.1 Transmitter test specifications . 10
5.3.1.1 Frequency error . 10
5.3.1.2 Carrier power (conducted) . 10
5.3.1.3 Adjacent channel power . 10
5.3.1.4 Conducted spurious emissions . 10
5.3.1.5 Intermodulation attenuation . 10
5.3.1.6 Keying transient frequency behaviour . 10
5.3.1.7 Cabinet Radiation . 11
5.3.2 Receiver test specifications . 11
5.3.2.1 Sensitivity . 11
5.3.2.2 Adjacent channel rejection . 11
5.3.2.3 Spurious response rejection . 11
5.3.2.4 Intermodulation response rejection . 11
5.3.2.5 Blocking or desensitisation . 11
5.3.2.6 Conducted spurious emissions . 11
5.3.2.7 Cross modulation rejection . 11
5.3.2.8 Cabinet Radiation . 11
ETSI
4 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 12
Annex B (informative): The EN title in the official languages . 14
Annex C (informative): Bibliography . 15
History . 16
ETSI
5 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the ETSI standards
One-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.5] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering Ground-based UHF radio transmitters, receivers and
transceivers for the UHF aeronautical mobile service using amplitude modulation, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.4].
ETSI
6 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
1 Scope
The present document applies to DSB AM ground base stations, with channel separations of 25 kHz intended for
analogue speech. The scope of the present document is limited to ground based transmitters, receivers and transceivers.
These radio equipment types are capable of operating in all or any part of the aeronautical frequency band between
225 MHz and 399,975 MHz.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2,
which states that ". radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive as well as essential requirements under the Single European Sky
Interoperability Regulation (as amended) [i.3] and related implementing rules may apply to equipment within the scope
of the present document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references,only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 302 617-1 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile
service using amplitude modulation; Part 1: Technical characteristics and methods of
measurement".
[2] ETSI EN 300 113-1 (V1.6.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using
constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical
characteristics and methods of measurement".
2.2 Informative references
The following refe
...
SLOVENSKI STANDARD
01-december-2010
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP (50 7DOQL
8+)UDGLMVNLRGGDMQLNLVSUHMHPQLNLLQVSUHMHPQLNLRGGDMQLNL]D8+)DHURQDYWLþQR
PRELOQRVWRULWHYNLXSRUDEOMDDPSOLWXGQRPRGXODFLMRGHO +DUPRQL]LUDQL(1NL
]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Ground-based UHF
radio transmitters, receivers and transceivers for the UHF aeronautical mobile service
using amplitude modulation - Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 302 617-2 Version 1.1.1
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Ground-based UHF radio
transmitters, receivers and transceivers for the UHF
aeronautical mobile service using amplitude modulation;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
2 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Reference
DEN/ERM-JTFEA-002-2
Keywords
aeronautical, AM, DSB, radio, testing, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Technical requirements specifications . 7
4.1 Environmental profile . 7
4.2 Conformance requirements . 8
4.2.1 Transmitter requirements . 8
4.2.1.1 Frequency error . 8
4.2.1.2 Carrier power (conducted) . 8
4.2.1.3 Adjacent channel power . 8
4.2.1.4 Conducted spurious emissions . 8
4.2.1.5 Intermodulation attenuation . 8
4.2.1.6 Keying transient frequency behaviour . 8
4.2.1.7 Cabinet Radiation . 8
4.2.2 Receiver requirements . 8
4.2.2.1 Sensitivity . 8
4.2.2.2 Adjacent channel rejection . 8
4.2.2.3 Spurious response rejection . 9
4.2.2.4 Intermodulation response rejection . 9
4.2.2.5 Blocking or desensitisation . 9
4.2.2.6 Conducted spurious emissions . 9
4.2.2.7 Cross modulation rejection . 9
4.2.2.8 Cabinet radiation . 9
5 Testing for compliance with technical requirements . 9
5.1 Environmental conditions for testing . 9
5.2 Interpretation of the measurement results . 9
5.3 Essential radio test suites . 10
5.3.1 Transmitter test specifications . 10
5.3.1.1 Frequency error . 10
5.3.1.2 Carrier power (conducted) . 10
5.3.1.3 Adjacent channel power . 10
5.3.1.4 Conducted spurious emissions . 10
5.3.1.5 Intermodulation attenuation . 10
5.3.1.6 Keying transient frequency behaviour . 10
5.3.1.7 Cabinet Radiation . 11
5.3.2 Receiver test specifications . 11
5.3.2.1 Sensitivity . 11
5.3.2.2 Adjacent channel rejection . 11
5.3.2.3 Spurious response rejection . 11
5.3.2.4 Intermodulation response rejection . 11
5.3.2.5 Blocking or desensitisation . 11
5.3.2.6 Conducted spurious emissions . 11
5.3.2.7 Cross modulation rejection . 11
5.3.2.8 Cabinet Radiation . 11
ETSI
4 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 12
Annex B (informative): The EN title in the official languages . 14
Annex C (informative): Bibliography . 15
History . 16
ETSI
5 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the ETSI standards
One-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.5] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering Ground-based UHF radio transmitters, receivers and
transceivers for the UHF aeronautical mobile service using amplitude modulation, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.4].
ETSI
6 Final draft ETSI EN 302 617-2 V1.1.1 (2010-06)
1 Scope
The present document applies to DSB AM ground base stations, with channel separations of 25 kHz intended for
analogue speech. The scope of the present document is limited to ground based transmitters, receivers and transceivers.
These radio equipment types are capable of operating in all or any part of the aeronautical frequency band between
225 MHz and 399,975 MHz.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2,
which states that ". radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive as well as essential requirements under the Single European Sky
Interoperability Regulation (as amended) [i.3] and related implementing rules may apply to equipment within the scope
of the present document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references,only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 302 617-1 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Ground-based UHF radio transmitters, receivers and transcei
...