SIST EN 13763-25:2004

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Eksplozivi za civilno uporabo - Detonatorji in zakasnilniki - 25. del: Ugotavljanje prenosne zmogljivosti površinskih konektorjev, zakasnilnikov in spojnih elementovLQGHUQExplosifs a usage civil - Détonateurs et relais - Partie 25:
Détermination de la capacité de transmission des relais et des manchonsExplosives for civil uses - Detonators and relays - Part 25: Determination of transfer capability of surface connectors, relays and coupling accessories71.100.30Eksplozivi. PirotehnikaExplosives. PyrotechnicsICS:Ta slovenski standard je istoveten z:EN 13763-25:2004SIST EN 13763-25:2004en01-september-2004SIST EN 13763-25:2004SLOVENSKI
STANDARD







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13763-25May 2004ICS 71.100.30English versionExplosives for civil uses - Detonators and relays - Part 25:Determination of transfer capability of surface connectors, relaysand coupling accessoriesExplosifs à usage civil - Détonateurs et relais - Partie 25: Détermination de la capacité de transmission des relais etdes manchonsExplosivstoffe für zivile Zwecke - Zünder undVerzögerungselemente - Teil 25: Bestimmung desÜbertragungsvermögens von Oberflächenverbindern,Verzögerern und VerbindernThis European Standard was approved by CEN on 2 February 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13763-25:2004: E



EN 13763-25:2004 (E)2ContentspageForeword.3Introduction.51Scope.62Normative references.63Terms and definitions.64Test pieces.65Apparatus.66Procedure.67Test report.7Annex A (informative)
Range of applicability of the test method.8Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or otherprovisions of EU Directives.9



EN 13763-25:2004 (E)3ForewordThis document (EN 13763-25:2004) has been prepared by Technical Committee CEN /TC 321, "Explosives for civiluses", the secretariat of which is held by AENOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by November 2004,and conflicting national standards shall be withdrawn at the latestby November 2004.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.Annex A is informative.This European Standard is one of a series of standards with the generic title Explosives for civil uses – Detonatorsand relays. The other parts of this series are listed below:EN 13763-1Part 1: RequirementsEN 13763-2Part 2: Determination of thermal stabilityEN 13763-3Part 3: Determination of sensitiveness to impactEN 13763-4Part 4: Determination of resistance to abrasion of leading wires and shock tubesEN 13763-5Part 5: Determination of resistance to cutting damage of leading wires and shock tubesEN 13763-6Part 6: Determination of resistance to cracking at low temperatures of leading wiresEN 13763-7Part 7: Determination of the mechanical strength of leading wires, shock tubes, connections,crimps and closuresEN 13763-8Part 8: Determination of resistance to vibration of plain detonatorsEN 13763-9Part 9: Determination of resistance to bending of detonatorsprEN 13763-10Part 10:Method for the determination of resistance to torsion of sealing plugsEN 13763-11Part 11: Determination of resistance to damage by dropping of detonators and relaysEN 13763-12Part 12: Determination of resistance to hydrostatic pressureEN 13763-13Part 13: Determination of resistance of electric detonator to electrostatic dischargeEN 13763-15Part 15: Determination of equivalent initiating capabilityEN 13763-16Part 16: Determination of delay accuracyEN 13763-17Part 17: Determination of no-fire current of electric detonatorsEN 13763-18Part 18: Determination of series firing current of electric detonatorsEN 13763-19Part 19: Determination of firing impulse of electric detonatorsEN 13763-20Part 20: Determination of total el
...