iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 725-3:2000

(Main)

Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas

Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas

This part of EN 725 describes a method for the determination of the oxygen content of non-oxide powders used for technical ceramics, using a hot carrier gas thermal extraction method.

Hochleistungskeramik - Prüfverfahren für keramische Pulver - Teil 3: Bestimmung des Sauerstoffgehaltes in Nichtoxid-Pulvern mittels Trägergasheißextraktion

Dieser Teil von EN 725 beschreibt ein Verfahren zur Bestimmung des Sauerstoffgehaltes mittels Trägergasheissextraktion in Nichtoxidpulvern, die für technische Keramik verwendet werden.

Céramiques techniques avancées - Méthodes d'essai pour poudres céramiques - Partie 3: Détermination de la teneur en oxygene de poudres non-oxydes par extraction a chaud sous gaz porteur

La présente partie de l'EN 725 décrit un mode opératoire permettant de déterminer la teneur en oxygene de poudres non-oxydes, a l'aide d'une méthode d'extraction a chaud utilisant un gaz porteur chaud.

Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas

General Information

Status
Withdrawn
Publication Date
30-Nov-2000
Withdrawal Date
10-Jun-2007
ICS
81.060.30 - Advanced ceramics
Technical Committee
I13 - Imaginarni 13
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
11-Jun-2007
Due Date
04-Jul-2007
Completion Date
11-Jun-2007
Mandate
M/BC/CEN/90/4 - Request concerning the realisation of a standardization programme in the field of advanced technical ceramics
Ref Project
EN 725-3:1994 - Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas

Relations

Child
SIST ENV 725-4:2000 - Advanced technical ceramics - Methods of test for ceramic powders - Part 4: Determination of oxygen content in aluminium nitride by XRF analysis
Effective Date
22-Dec-2008
Replaced By
SIST EN 725-3:2007 - Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas
Effective Date
01-May-2007

Buy Standard

EN 725-3:2000EN 725-3:2000
PreviousNext
Standard
EN 725-3:2000
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 725-3:2000
01-december-2000
Advanced technical ceramics - Methods of test for ceramic powders - Part 3:
Determination of the oxygen content of non-oxides by thermal extraction with a
carrier gas
Advanced technical ceramics - Methods of test for ceramic powders - Part 3:
Determination of the oxygen content of non-oxides by thermal extraction with a carrier
gas
Hochleistungskeramik - Prüfverfahren für keramische Pulver - Teil 3: Bestimmung des
Sauerstoffgehaltes in Nichtoxid-Pulvern mittels Trägergasheißextraktion
Céramiques techniques avancées - Méthodes d'essai pour poudres céramiques - Partie
3: Détermination de la teneur en oxygene de poudres non-oxydes par extraction a chaud
sous gaz porteur
Ta slovenski standard je istoveten z: EN 725-3:1994
ICS:
81.060.30 Sodobna keramika Advance
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 20509:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of oxidation resistance of non-oxide monolithic ceramics (ISO 20509:2003)
EN ISO 20509:2023

ISO 20509:2003 describes the method of test for determining the oxidation resistance of non-oxide monolithic ceramics, such as silicon nitride, sialon and silicon carbide at high temperatures. This International Standard is designed to provide an assessment of the mass and dimensional changes of test pieces following oxidation at high temperature in an oxidizing atmosphere, and to assess whether oxidation has a significant effect on the subsequent strength. This test method may be used for materials development, quality control, characterization, and design data generation purposes.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 24370:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for fracture toughness of monolithic ceramics at room temperature by chevron-notched beam (CNB) method (ISO 24370:2005)
EN ISO 24370:2023

This International Standard ISO 24370 specifies a test method for determining the fracture toughness of monolithic ceramic materials at room temperature by the chevron-notched beam (CNB) method.
This International Standard is applicable to monolithic ceramics and whisker- or particulate-reinforced ceramics that are regarded as macroscopically homogeneous. It is not applicable to continuous-fibre reinforced ceramic composites.
This International Standard is usually applicable to ceramic materials with a fracture toughness less than about 12 MPa(m1/2). The test method is applicable to materials with a flat crack-growth resistance curve and may be applicable to materials with a rising crack-growth resistance curve (R-curve).

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 17947:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for chemical analysis of fine silicon nitride powders (ISO 17947:2014)
EN ISO 17947:2023

The International Standard specifies the methods for the chemical analysis of fine silicon nitride powders used as the raw material for fine ceramics.
This International Standard stipulates the determination methods of total silicon, total nitrogen, aluminium, iron, calcium, oxygen, carbon, fluorine, and chlorine in fine silicone nitride powders.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 17092:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of corrosion resistance of monolithic ceramics in acid and alkaline solutions (ISO 17092:2005)
EN ISO 17092:2023

ISO 17092:2005 describes the test method for determining the corrosion resistance of fine ceramics in acid and alkaline solutions, such as sulfuric acid and sodium hydroxide. This International Standard is designed to provide an assessment of the mass changes and dimensional changes of test specimens following the corrosion test immersed in the corrosive liquids, and to assess whether corrosion has a significant effect on the subsequent strength. This test method may be used for development of materials, quality control, characterization, and design-data generation purposes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 20501:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Weibull statistics for strength data (ISO 20501:2019)
EN ISO 20501:2022

This document covers the reporting of uniaxial strength data and the estimation of probability distribution parameters for advanced ceramics which fail in a brittle fashion. The failure strength of advanced ceramics is treated as a continuous random variable. Typically, a number of test specimens with well-defined geometry are brought to failure under well-defined isothermal loading conditions. The load at which each specimen fails is recorded. The resulting failure stresses are used to obtain parameter estimates associated with the underlying population distribution.
This document is restricted to the assumption that the distribution underlying the failure strengths is the two-parameter Weibull distribution with size scaling. Furthermore, this document is restricted to test specimens (tensile, flexural, pressurized ring, etc.) that are primarily subjected to uniaxial stress states. Subclauses 6.4 and 6.5 outline methods of correcting for bias errors in the estimated Weibull parameters, and to calculate confidence bounds on those estimates from data sets where all failures originate from a single flaw population (i.e. a single failure mode). In samples where failures originate from multiple independent flaw populations (e.g. competing failure modes), the methods outlined in 6.4 and 6.5 for bias correction and confidence bounds are not applicable.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 20504:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Mechanical properties of ceramic composites at room temperature - Determination of compressive properties (ISO 20504:2022)
EN ISO 20504:2022

This document describes procedures for determination of the compressive behaviour of ceramic matrix composite materials with continuous fibre reinforcement at room temperature. This method applies to all ceramic matrix composites with a continuous fibre reinforcement, uni-directional (1D), bi-directional (2D) and tri-directional (xD, with 2 < x < 3), tested along one principal axis of reinforcement or off axis conditions. This method also applies to carbon-fibre-reinforced carbon matrix composites (also known as carbon/carbon or C/C). Two cases of testing are distinguished: compression between platens and compression using grips.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 21821:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of densification properties of ceramic powders on natural sintering (ISO 21821:2019)
EN ISO 21821:2022

This document specifies the test method to determine the extent to which ceramic powder compacts made of granulated or ungranulated ceramic powders are densified, when they are sintered at a high temperature without the application of any external pressure or external densification force. The test method is applicable to pure oxides, mixtures of oxides and solid solutions, and is also applicable to non-oxides (e.g. carbides, nitrides) that can be sintered under vacuum or constant gas pressure (1 bar or less) to prevent oxidation or decomposition. The test method is not applicable to ceramics that can only be sintered using pressure-assisted sintering techniques such as hot pressing (HP), hot isostatic pressing (HIP), gas pressure sintering (GPS) or spark plasma sintering (SPS). Inorganic sintering additives can be used where their presence is reported.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 21814:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for chemical analysis of aluminium nitride powders (ISO 21814:2019)
EN ISO 21814:2022

This document specifies methods for the chemical analysis of fine aluminium nitride powders used as the raw material for fine ceramics.
This document stipulates the determination methods of the aluminium, total nitrogen, boron, calcium, copper, iron, magnesium, manganese, molybdenum, nickel, potassium, silicon, sodium, titanium, tungsten, vanadium, zinc, zirconium, carbon, chlorine, fluorine, and oxygen contents in aluminium nitride powders. The aluminium content is determined by using either an acid pressure decomposition-CyDTA-zinc back titration method or an acid digestion-inductively coupled plasma-optical emission spectrometry (ICP-OES) method. The total nitrogen content is determined by using an acid pressure decomposition-distillation separation-acidimetric titration method, a direct decomposition-distillation separation-acidimetric titration method, or an inert gas fusion-thermal conductivity method. The boron, calcium, copper, iron, magnesium, manganese, molybdenum, nickel, potassium, silicon, sodium, titanium, tungsten, vanadium and zinc contents are determined by using an acid digestion-ICP-OES method or an acid pressure decomposition-ICP-OES method. The sodium and potassium contents are determined via an acid pressure decomposition-flame emission method or an acid pressure decomposition-atomic absorption spectrometry method. The oxygen content is determined by using an inert gas fusion-IR absorption spectrometry method, while that of carbon is determined via a combustion-IR absorption spectrometry method or a combustion-conductometry method. The chlorine and fluorine contents are determined by using a pyrohydrolysation method followed by ion chromatography or spectrophotometry.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 21813:2023(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for chemical analysis of high purity barium titanate powders (ISO 21813:2019)
EN ISO 21813:2022

ISO 21813 specifies methods for the chemical analysis of fine high purity barium titanate powders used as the raw material for fine ceramics.
ISO 21813 stipulates the determination methods of the barium, titanium, aluminium, cadmium, calcium, cobalt, dysprosium, iron, lead, magnesium, manganese, nickel, niobium, potassium, silicon, sodium, strontium, vanadium, zirconium, carbon, oxygen and nitrogen contents in high purity barium titanate powders. The barium and titanium contents, the major elements, are determined by using an acid decomposition-gravimetric method or an acid decomposition-inductively coupled plasma-optical emission spectrometry (ICP-OES) method. The aluminium, cadmium, calcium, chromium, cobalt, dysprosium, iron, lead, magnesium, manganese, nickel, niobium, potassium, silicon, strontium, vanadium and zirconium contents are simultaneously determined via an acid digestion-ICP-OES method. The nitrogen content is determined by using an inert gas fusion-thermal conductivity method, while that of oxygen is determined via an inert gas fusion-IR absorption spectrometry method. Finally, the carbon content is determined using a combustion-IR absorption spectrometry method or a combustion-conductometry method.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19629:2022(Main)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Thermophysical properties of ceramic composites - Determination of unidimensional thermal diffusivity by flash method (ISO 19629:2018)
EN ISO 19629:2022

This document describes the flash method for the determination of thermal diffusivity of ceramic matrix composites with continuous fibre reinforcement.
In order to conform with the unidimensional heat transfer hypothesis, the experimental conditions are defined such that the material behaves in a homogeneous manner. This involves performing tests in one symmetry axis of the composite.
The method is applicable to materials which are physically and chemically stable during the measurement, and covers the range of temperature from 100 K to 2 800 K. It is suitable for the measurement of thermal diffusivity values in the range 10−4 m2∙s−1 to 10−7 m2∙s−1.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day