SIST EN 300 113-1 V1.5.1:2003
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement
- Abstract
Update of measurement methods of EN 300 113 when applied to equipment operating in discontinuous transmission modes.
- Status
- Published
- Publication Date
- 30-Nov-2003
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 01-Dec-2003
- Due Date
- 01-Dec-2003
- Completion Date
- 01-Dec-2003
SIST EN 300 113-1 V1.5.1:2003 is the Slovenian adoption of ETSI EN 300 113-1 Version 1.5.1, published by SIST. It specifies the technical characteristics and measurement methods for land mobile radio equipment used for data and/or speech transmission with constant or non-constant envelope modulation and an antenna connector.
The standard focuses on the measurements needed to judge whether this equipment uses spectrum well and limits unwanted emissions. It is written for equipment that transmits continuously or in discontinuous bursts, which is important for radios that send packets or messages rather than a steady carrier.
What does SIST EN 300 113-1 V1.5.1:2003 specify?
SIST EN 300 113-1 V1.5.1:2003 covers the minimum characteristics needed to reduce harmful interference and use the available frequencies acceptably. It applies to land mobile service equipment operating between 30 MHz and 1 GHz, with channel separations of 12.5 kHz, 20 kHz and 25 kHz, for digital and combined analogue/digital equipment intended for data and/or speech.
The document is organized into clauses for scope, references, definitions, general conditions, transmitter limits and tests, receiver limits and tests, duplex operation, and measurement uncertainty. It also includes annexes that give radiated test arrangements, measurement receiver requirements, optional station identification, sample-selection guidance, and background information.
| Annex | What it covers |
|---|---|
| Annex A | Radiated measurement sites and arrangements, including anechoic chamber, ground-plane chamber, and OATS |
| Annex B | Specifications for some particular measurement arrangements, including the power measuring receiver and spectrum analyser |
| Annex C | Optional station identification characteristics for private mobile radio systems |
| Annex D | Test and sample selection for equipment with alignment range and switching range combinations |
| Annex E | Information on modulation, coding and format |
| Annex F | Bibliography |
The foreword also points readers to other ETSI standards for related access protocols. In practice, that means EN 300 113-1 deals with the radio characteristics and measurement methods, not the whole system protocol.
What are the key requirements of SIST EN 300 113-1 V1.5.1:2003?
SIST EN 300 113-1 V1.5.1:2003 sets out how to test the transmitter, receiver, and duplex performance of qualifying equipment, and how to interpret the results against the limits in clause 5. The most important practical point is that the same equipment may need different measurement procedures depending on whether it uses constant or non-constant envelope modulation and whether it operates continuously or in bursts.
Test conditions and how results are judged
Clause 6 requires measurements under normal conditions and, where stated, under extreme conditions. The equipment is powered from a test power source with low internal impedance, and the supply voltage must stay within a tight tolerance during the test; that matters because power and frequency measurements are sensitive to supply variation.
Clause 4.3 says the measured value is compared directly with the relevant limit, and the laboratory’s actual measurement uncertainty must be reported and kept within the values in clause 11. Clause 4.4 lets the manufacturer choose bit streams or messages for testing, while clauses 4.5 and 4.6 explain how to treat continuous-mode and discontinuous-mode equipment. For burst-mode equipment, some measurements may need to be done within a burst or over repeated bursts and then averaged.
Transmitter limits and measurements
Clause 5.1 covers frequency error, carrier power, effective radiated power, adjacent channel power, spurious emissions, intermodulation attenuation, attack time, release time, and transient behavior. These checks tell you whether the transmitter stays on frequency, stays within its power class, and avoids splattering energy into other channels when it turns on or off.
Clause 8 explains the methods. For example, carrier power is checked at the lowest and highest intended power settings, and the user is not supposed to have access to the power adjustment control. Effective radiated power is used when there is no external antenna connector, so the test method matches the physical design.
Clause 8.5 and 8.6 cover adjacent channel power and spurious emissions, including the different reference bandwidths used for non-constant envelope modulation equipment. Clause 8.7 applies intermodulation attenuation only to transmitters used in base stations. Clauses 8.8, 8.9 and 8.10 cover attack time, release time and transient behavior, including time-domain plots of power and frequency and measurements in adjacent channels. In practice, these are the checks that show whether a transmitter creates short but troublesome interference during switching events.
Receiver limits and measurements
Clause 5.2 sets the receiver requirements, including maximum usable sensitivity, average usable sensitivity, error behavior at high input levels, co-channel rejection, adjacent channel selectivity, spurious response rejection, intermodulation response rejection, blocking or desensitization, and spurious radiations. These measurements show how well the receiver can hear the wanted signal when other signals are present nearby or far away in frequency.
Clause 9 gives the measurement methods. The wanted-signal level used for degradation measurements is defined in clause 9.3, and the tests may use continuous bit streams or messages. Clauses 9.5 to 9.9 are especially important because they describe how to measure rejection against same-channel interferers, adjacent-channel interferers, spurious responses, intermodulation products, and blocking signals.
Clause 9.7 is notable because it combines a search over a limited frequency range with calculated frequencies elsewhere, which is meant to catch likely spurious responses without testing every frequency in the spectrum. Clause 9.10 covers spurious radiations from the receiver side.
Duplex operation
Clause 10 adds tests for equipment designed for simultaneous transmission and reception. The equipment must be fitted with a duplex filter for these tests, and the measurements are done on a single frequency pair specified by the manufacturer. In practice, this section checks that transmitting does not overload or desensitize the receiver when both directions are active at the same time.
Measurement uncertainty and radiated tests
Clause 11 gives maximum acceptable uncertainty values for key measurements such as RF frequency, RF power, radiated power, adjacent channel power, spurious emissions, and duplex desensitization. That matters because a result is only meaningful if the laboratory knows how much uncertainty sits behind it.
Annex A gives the radiated test sites and arrangements used for field measurements, and Annex B defines the required characteristics of the power measuring receiver and spectrum analyser. Together, they make the measurement methods repeatable across laboratories.
What terms does SIST EN 300 113-1 V1.5.1:2003 define?
- Angle modulation - phase modulation or frequency modulation.
- Base station - equipment with an antenna socket for use with an external antenna in a fixed location.
- Conducted measurements - measurements made with a direct 50 Ω connection to the equipment under test.
- Burst or transmission (physical) - one or several packets transmitted between power on and power off of a transmitter.
- Window - a set of inter-related transmissions that may be limited in time by an access protocol.
- Session - a set of inter-related packet exchanges covering initiation, data transmission, and termination.
- PEP (Peak Envelope Power) - the average power supplied to the artificial antenna during one RF cycle at the highest crest of the modulation envelope.
Who uses SIST EN 300 113-1 V1.5.1:2003?
SIST EN 300 113-1 V1.5.1:2003 is used by radio equipment manufacturers, conformity assessment labs, and engineering teams that design or test land mobile radios for data and/or speech. It is also useful to quality managers and buyers who need to check that a product has been measured against a recognized European method.
The standard is relevant in professional mobile radio (PMR), mobile services, and electromagnetic compatibility work. Regulators and certification bodies use it when they need a common basis for limits, test setups, and report content, especially for equipment that uses burst transmission or mixed analogue/digital operation.
Which standards are used with SIST EN 300 113-1 V1.5.1:2003?
- ETSI EN 300 086-1 - provides the analogue-speech measurement baseline and is referenced when combined analogue/digital equipment has already been tested for the analogue part.
- ETSI EN 300 390-1 - gives the definition and method for average usable sensitivity for equipment without an external antenna connector.
- ETSI EN 300 793 - is used for selecting equipment for testing and for sample selection when alignment range and switching range differ.
- ETSI TR 100 028 - is used to calculate measurement uncertainty.
- ETSI TR 102 273 - gives verification guidance for radiated test sites.
- ETSI EN 300 471-1 - is cited as an example of other ETSI standards dealing with access protocols.
- CEPT/ERC/REC/74.01 - is noted as consistent with the spurious emission limits used in the document.
- ANSI C63.5 - is used for dipole antenna construction in radiated testing.
- IEC 60489-3 - is referenced for acoustic coupler frequency-response correction.
- ITU-T Recommendation V.22 and V.23 - appear in the identification annex as modulation options.
What does the SIST EN 300 113-1 V1.5.1:2003 document contain?
SIST EN 300 113-1 V1.5.1:2003 contains tables of transmitter and receiver limits, including values tied to channel separation, operating mode, and test conditions. It also contains the measurement procedures for frequency error, power, adjacent channel behavior, spurious emissions, sensitivity, selectivity, blocking, and duplex operation.
The document includes several figures for test arrangements and time-domain transient behavior, plus annex figures for radiated test sites and identification block structure. Annex B provides detailed characteristics for the measuring receiver, including IF filter behavior and spectrum analyser performance.
Annex C is especially detailed: it lays out identification block structure, synchronization, coding, field organization, and combinations for different station-identification uses. Annex D shows how to choose test samples when a product family has alignment ranges and switching ranges that are not the same, which matters for type approval across a frequency range.
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
SIST EN 300 113-1 V1.5.1:2003 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement". This standard covers: Update of measurement methods of EN 300 113 when applied to equipment operating in discontinuous transmission modes.
Update of measurement methods of EN 300 113 when applied to equipment operating in discontinuous transmission modes.
SIST EN 300 113-1 V1.5.1:2003 is classified under the following ICS (International Classification for Standards) categories: 33.060.99 - Other equipment for radiocommunications; 33.070.01 - Mobile services in general; 33.100.01 - Electromagnetic compatibility in general. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 300 113-1 V1.5.1:2003 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2003
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP (50 ±
6WRULWHYNRSHQVNLKPRELOQLKNRPXQLNDFLM±5DGLMVNDRSUHPD]DSUHQRVSRGDWNRY
R]LURPDJRYRUD NLXSRUDEOMDPRGXODFLMRVNRQVWDQWQRDOLQHNRQVWDQWQRRYRMQLFR
LQLPDDQWHQVNLSULNOMXþHN±GHO 7HKQLþQHNDUDNWHULVWLNHLQPHULOQHPHWRGH
Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service;
Radio equipment intended for the transmission of data (and/or speech) using constant or
non-constant envelope modulation and having an antenna connector; Part 1: Technical
characteristics and methods of measurement
Ta slovenski standard je istoveten z: EN 300 113-1 Version 1.5.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land mobile service;
Radio equipment intended for the transmission
of data (and/or speech) using constant or non-constant
envelope modulation and having an antenna connector;
Part 1: Technical characteristics and
methods of measurement
2 ETSI EN 300 113-1 V1.5.1 (2003-09)
Reference
REN/ERM-TG32-046-1
Keywords
antenna, data, mobile, radio, speech, PMR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, send your comment to:
editor@etsi.org
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2003.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI EN 300 113-1 V1.5.1 (2003-09)
Contents
Intellectual Property Rights.8
Foreword.8
Introduction .8
1 Scope.10
2 References.11
3 Definitions, symbols and abbreviations .12
3.1 Definitions.12
3.2 Symbols.13
3.3 Abbreviations.13
4 General.14
4.1 Selection of equipment for testing purposes.15
4.2 Mechanical and electrical design.15
4.2.1 General.15
4.2.2 Controls.15
4.2.3 Transmitter shut-off facility.15
4.2.4 Marking.15
4.3 Interpretation of the measurement results .15
4.4 Testing using bit streams or messages.16
4.5 Measuring continuous mode equipment.16
4.6 Measuring discontinuous mode equipment .16
5 Technical characteristics.16
5.1 Transmitter parameter limits .16
5.1.1 Frequency error.16
5.1.2 Carrier power (conducted) .17
5.1.3 Effective radiated power.17
5.1.4 Adjacent channel power.18
5.1.5 Spurious emissions.18
5.1.6 Intermodulation attenuation.19
5.1.7 Transmitter attack time .19
5.1.8 Transmitter release time.19
5.1.9 Transient behaviour of the transmitter .19
5.1.9.1 Time domain analysis of power and frequency.19
5.1.9.2 Adjacent channel transient power .20
5.1.9.2.1 Equipment measured as constant envelope angle modulation equipment .20
5.1.9.2.2 Equipment measured as non-constant envelope modulation equipment .20
5.2 Receiver parameter limits.21
5.2.1 Maximum usable sensitivity (data or messages, conducted) .21
5.2.2 Average usable sensitivity (data or messages, field strength).21
5.2.3 Error behaviour at high input levels.21
5.2.4 Co-channel rejection.21
5.2.5 Adjacent channel selectivity .21
5.2.6 Spurious response rejection .22
5.2.7 Intermodulation response rejection.22
5.2.8 Blocking or desensitization.22
5.2.9 Spurious radiations.22
5.3 Duplex operation - receiver limits.23
5.3.1 Receiver desensitization and maximum usable sensitivity (with simultaneous transmission and
reception) .23
5.3.2 Receiver spurious response rejection (with simultaneous transmission and reception).23
6 Test conditions, power sources and ambient temperatures .23
6.1 Normal and extreme test conditions .23
6.2 Test power source.23
ETSI
4 ETSI EN 300 113-1 V1.5.1 (2003-09)
6.3 Normal test conditions.23
6.3.1 Normal temperature and humidity.23
6.3.2 Normal test power source .24
6.3.2.1 Mains voltage.24
6.3.2.2 Regulated lead-acid battery power sources used on vehicles.24
6.3.2.3 Other power sources.24
6.4 Extreme test conditions .24
6.4.1 Extreme temperatures.24
6.4.2 Extreme test source voltages.24
6.4.2.1 Mains voltage.24
6.4.2.2 Regulated lead-acid battery power sources on vehicles .24
6.4.2.3 Power sources using other types of batteries.25
6.4.2.4 Other power sources.25
6.5 Procedure for tests at extreme temperatures.25
6.5.1 Procedure for equipment designed for continuous operation.25
6.5.2 Procedure for equipment designed for intermittent operation .26
7 General conditions.26
7.1 Arrangements for test signals applied to the receiver input.26
7.2 Receiver mute or squelch facility.26
7.3 Normal test signals (wanted and unwanted signals).26
7.3.1 Equipment measured as constant envelope angle modulation equipment .26
7.3.2 Equipment measured as non-constant envelope modulation equipment.27
7.4 Encoder for receiver measurements .28
7.5 Transceiver data interface.28
7.6 Impedance.28
7.7 Artificial antenna.28
7.8 Tests of equipment with a duplex filter .28
7.9 Facilities for access .28
7.9.1 Analogue access.28
7.9.2 Test points for bit stream measurements.29
7.9.3 Coupling arrangements.29
7.9.3.1 Arrangements for measurements with continuous bit streams.29
7.9.3.2 Arrangements for measurements with messages.29
7.10 Test site and general arrangements for measurements involving the use of radiated fields .29
7.11 Modes of operation of the transmitter .30
8 Methods of measurement for transmitter parameters.30
8.1 Frequency error.30
8.1.1 Definition.30
8.1.2 Method of measurement.30
8.2 Carrier power (conducted).31
8.2.1 Definitions.31
8.2.1.1 Equipment measured as constant envelope angle modulation equipment.31
8.2.1.2 Equipment measured as non-constant envelope modulation equipment.31
8.2.2 Method of measurement.31
8.2.2.1 Equipment measured as constant envelope angle modulation equipment.31
8.2.2.2 Equipment measured as non-constant envelope modulation equipment.32
8.3 Effective radiated power (field strength).32
8.3.1 Definition.32
8.3.1.1 Equipment measured as constant envelope angle modulation equipment.32
8.3.1.2 Equipment measured as non-constant envelope modulation equipment.32
8.3.2 Methods of measurement.33
8.3.2.1 Equipment measured as constant envelope angle modulation equipment.34
8.3.2.2 Equipment measured as non-constant envelope modulation equipment.35
8.4 Maximum permissible frequency deviation .36
8.4.1 Definition.36
8.4.2 Method of measurement.36
8.5 Adjacent channel power .37
8.5.1 Definition.37
8.5.2 Method of measurement.37
8.6 Spurious emissions.38
ETSI
5 ETSI EN 300 113-1 V1.5.1 (2003-09)
8.6.1 Definition.38
8.6.2 Method of measuring the power level .39
8.6.2.1 Equipment measured as constant envelope angle modulation equipment.39
8.6.2.2 Equipment measured as non-constant envelope modulation equipment.39
8.6.3 Method of measuring the effective radiated power.40
8.6.3.1 Equipment measured as constant envelope angle modulation equipment.40
8.6.3.2 Equipment measured as non-constant envelope modulation equipment.41
8.7 Intermodulation attenuation.42
8.7.1 Definition.42
8.7.2 Method of measurement.43
8.8 Transmitter attack time.43
8.8.1 Definition.44
8.8.2 Method of measurement.44
8.9 Transmitter release time .45
8.9.1 Definition.45
8.9.2 Method of measurement.45
8.10 Transient behaviour of the transmitter.45
8.10.1 Definitions.46
8.10.2 Timings, frequencies and powers .47
8.10.3 Methods of measurement.51
8.10.3.1 Time domain measurements of power and frequency.51
8.10.3.2 Test arrangement and characteristics of the FM modulation meter .52
8.10.3.3 Adjacent channel transient power measurements.52
8.10.3.3.1 Definition.52
8.10.3.3.2 Equipment measured as constant envelope angle modulation equipment .52
8.10.3.3.3 Equipment measured as non-constant envelope modulation equipment .53
8.10.3.4 Characteristics of the adjacent channel transient power measuring device.54
9 Methods of measurement for receiver parameters .55
9.1 Maximum usable sensitivity (data or messages, conducted).55
9.1.1 Definition.55
9.1.2 Method of measurement with continuous bit streams.55
9.1.3 Method of measurement with messages .56
9.2 Average usable sensitivity (data or messages, field strength) .56
9.3 Level of the wanted signal for the degradation measurements (data or messages) .57
9.4 Error behaviour at high input levels .57
9.4.1 Definition.57
9.4.2 Method of measurement with continuous bit streams.57
9.4.3 Method of measurement with messages .58
9.5 Co-channel rejection.58
9.5.1 Definition.58
9.5.2 Method of measurement with continuous bit streams.58
9.5.3 Method of measurement with messages .59
9.6 Adjacent channel selectivity.61
9.6.1 Definition.61
9.6.2 Method of measurement with continuous bit streams.61
9.6.3 Method of measurement with messages .62
9.7 Spurious response rejection.63
9.7.1 Definition.63
9.7.2 Introduction to the method of measurement .64
9.7.3 Method of search over the "limited frequency range" .64
9.7.4 Method of measurement with continuous bit streams.65
9.7.5 Method of measurement with messages .66
9.8 Intermodulation response rejection .67
9.8.1 Definition.67
9.8.2 Method of measurement with continuous bit streams.67
9.8.3 Method of measurement with messages .68
9.9 Blocking or desensitization .69
9.9.1 Definition.69
9.9.2 Method of measurement with continuous bit streams.69
9.9.3 Method of measurement with messages .70
9.10 Spurious radiations.72
ETSI
6 ETSI EN 300 113-1 V1.5.1 (2003-09)
9.10.1 Definition.72
9.10.2 Method of measuring the power level .72
9.10.3 Method of measuring the effective radiated power.73
10 Duplex operation.74
10.1 Receiver desensitization (with simultaneous transmission and reception).75
10.1.1 Definition.75
10.1.2 Desensitization measured with continuous bit streams.75
10.1.2.1 Method of measurement when the equipment has a duplex filter.75
10.1.2.2 Method of measurement when the equipment has to operate with two antennas.76
10.1.3 Desensitization measured with messages .77
10.1.3.1 Method of measurement when the equipment has a duplex filter.77
10.1.3.2 Method of measurement when the equipment has to operate with two antennas.78
10.2 Receiver spurious response rejection (with simultaneous transmission and reception) .79
10.2.1 Definition.79
10.2.2 Method of measurement.79
11 Measurement uncertainty.80
Annex A (normative): Radiated measurement.81
A.1 Test sites and general arrangements for measurements involving the use of radiated fields.81
A.1.1 Anechoic chamber.81
A.1.2 Anechoic chamber with a conductive ground plane.82
A.1.3 Open Area Test Site (OATS) .83
A.1.4 Test antenna.84
A.1.5 Substitution antenna.85
A.1.6 Measuring antenna.85
A.2 Guidance on the use of radiation test sites .85
A.2.1 Verification of the test site .85
A.2.2 Preparation of the EUT.85
A.2.3 Power supplies to the EUT.85
A.2.4 Volume control setting for analogue speech tests .86
A.2.5 Range length.86
A.2.6 Site preparation.87
A.3 Coupling of signals.87
A.3.1 General.87
A.3.2 Data Signals.87
A.3.3 Speech and analogue signals .87
A.3.3.1 Acoustic coupler description.88
A.3.3.2 Calibration.88
Annex B (normative): Specification for some particular measurement arrangements.89
B.1 Power measuring receiver specification.89
B.1.1 IF filter.89
B.1.2 Attenuation indicator.90
B.1.3 RMS value indicator.90
B.1.4 Oscillator and amplifier.90
B.2 Spectrum analyser specification.91
B.3 Integrating and power summing device .91
Annex C (normative): Identification .92
C.1 Scope.92
C.2 General.92
C.3 Position of the identification code.93
C.3.1 Base stations.93
C.3.1.1 System without windows.93
C.3.1.2 Systems with windows.93
ETSI
7 ETSI EN 300 113-1 V1.5.1 (2003-09)
C.3.2 Mobile stations.93
C.4 Bit rates and modulations.94
C.5 Format of the identification.95
C.6 Synchronization.95
C.7 Code and block length.96
C.8 Contents of the identification block .96
C.8.1 Header.96
C.8.2 Country/regional code.97
C.8.3 National Information.98
C.8.3.1 Field description.98
C.8.3.2 Field size options .98
C.8.3.3 Options for the organization of the fields .99
C.8.3.4 Examples of user/system information usage.99
C.9 Combinations.100
C.9.1 List of possible combinations.100
C.9.2 Relations between country/regional code and allowed combinations .100
C.9.3 Interpretation of the fields of the ID block .102
Annex D (normative): Graphical representation of the selection of equipment and
frequencies for testing .103
D.1 Tests on a single sample.103
D.2 Tests and samples needed when the switching range is a subset of the alignment range .104
D.3 Tests and samples for a family of equipment where the alignment range is a subset of the total
operating frequency range.105
D.3.1 Test scenario 1.105
D.3.2 Test scenario 2.106
Annex E (informative): Information on modulation, coding and format .107
Annex F (informative): Bibliography.108
History .109
ETSI
8 ETSI EN 300 113-1 V1.5.1 (2003-09)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document is part 1 of a multi-part deliverable covering the Electromagnetic compatibility and Radio
spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech)
and having an antenna connector, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive".
NOTE: EN 300 113-1 (V1.4.1) covered both constant envelope angle modulation and non-constant envelope
modulation equipment. The present document includes more detailed measurement methods covering
equipment operating in continuous or discontinuous modes of transmission.
National transposition dates
Date of adoption of this EN: 15 August 2003
Date of latest announcement of this EN (doa): 30 November 2003
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 May 2004
Date of withdrawal of any conflicting National Standard (dow): 31 May 2004
Introduction
The present document is intended to specify the minimum performance and the methods of measurement of radio
equipment for use in the land mobile service as specified in the scope.
The present document is based upon EN 300 11
...