SIST EN 301 908-20 V5.2.1:2011

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 20: OFDMA TDD WMAN (Mobile WiMAX) TDD Base Stations (BS)33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-20 Version 5.2.1SIST EN 301 908-20 V5.2.1:2011en01-november-2011SIST EN 301 908-20 V5.2.1:2011SLOVENSKI
STANDARD



SIST EN 301 908-20 V5.2.1:2011



ETSI EN 301 908-20 V5.2.1 (2011-09) IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 20: OFDMA TDD WMAN (Mobile WiMAX) TDD Base Stations (BS)
Harmonized European Standard SIST EN 301 908-20 V5.2.1:2011



ETSI ETSI EN 301 908-20 V5.2.1 (2011-09)2
Reference DEN/MSG-TFES-009-20 Keywords broadband, IMT, IMT-2000, mobile, OFDMA, radio, regulation, TDD, WiMAX, WMAN ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-20 V5.2.1:2011



ETSI ETSI EN 301 908-20 V5.2.1 (2011-09)3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 10 3.3 Abbreviations . 10 4 Essential requirements specification . 11 4.1 Environmental profile . 11 4.2 Conformance requirements . 11 4.2.1 Introduction. 11 4.2.2 Transmitter Spectrum Emission Mask . 11 4.2.2.1 Definition . 11 4.2.2.2 Limits . 11 4.2.2.2.1 Spectrum emission mask for 5 MHz channel bandwidth . 12 4.2.2.2.2 Spectrum emission mask for 10 MHz channel bandwidth . 12 4.2.2.3 Conformance . 12 4.2.3 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 12 4.2.3.1 Definition . 12 4.2.3.2 Limits . 12 4.2.3.2.1 ACLR requirements for 5 MHz channel bandwidth . 12 4.2.3.2.2 ACLR requirements for 10 MHz channel bandwidth . 13 4.2.3.3 Conformance . 13 4.2.4 Transmitter spurious emissions . 13 4.2.4.1 Definition . 13 4.2.4.2 Limits . 13 4.2.4.2.1 General requirements . 13 4.2.4.2.2 Additional Spurious Emission Requirements . 14 4.2.4.3 Conformance . 14 4.2.5 Base station maximum output power . 14 4.2.5.1 Definition . 14 4.2.5.2 Limits . 14 4.2.5.3 Conformance . 15 4.2.6 Transmit intermodulation . 15 4.2.6.1 Definition . 15 4.2.6.2 Limits . 15 4.2.6.3 Conformance . 15 4.2.7 Receiver spurious emissions . 15 4.2.7.1 Definition . 15 4.2.7.2 Limits . 15 4.2.7.3 Conformance . 16 4.2.8 Receiver blocking characteristics . 16 4.2.8.1 Definition . 16 4.2.8.2 Limits . 16 4.2.8.3 Conformance . 16 4.2.9 Receiver intermodulation characteristics . 17 4.2.9.1 Definition . 17 4.2.9.2 Limits . 17 4.2.9.3 Conformance . 17 SIST EN 301 908-20 V5.2.1:2011



ETSI ETSI EN 301 908-20 V5.2.1 (2011-09)4 4.2.10 Receiver Adjacent Channel Selectivity. 17 4.2.10.1 Definition . 17 4.2.10.2 Limits . 18 4.2.10.3 Conformance . 18 5 Testing for compliance with technical requirements . 18 5.1 Environmental conditions for testing . 18 5.2 Product information . 18 5.3 Interpretation of the measurement results . 19 5.4 Essential radio test suites . 20 5.4.1 Transmitter Spectrum Emission Mask . 20 5.4.1.1 Method of measurement . 20 5.4.1.1.1 Initial conditions . 20 5.4.1.1.2 Procedure . 20 5.4.1.2 Test requirements . 21 5.4.2 Transmitter Adjacent Channel Leakage Power Ratio (ACLR) . 21 5.4.2.1 Method of measurement . 21 5.4.2.1.1 Initial conditions . 22 5.4.2.1.2 Procedure . 22 5.4.2.2 Test requirements . 22 5.4.3 Transmitter spurious emissions . 22 5.4.3.1 Method of measurement . 23 5.4.3.1.1 Initial conditions . 23 5.4.3.1.2 Procedure . 23 5.4.3.2 Test requirements . 23 5.4.4 Base Station maximum output power . 24 5.4.4.1 Method of measurement . 24 5.4.4.1.1 Initial conditions . 24 5.4.4.1.2 Procedure . 24 5.4.4.2 Test requirements . 25 5.4.5 Transmit Intermodulation . 25 5.4.5.1 Method of measurement . 25 5.4.5.1.1 Initial conditions . 25 5.4.5.1.2 Procedure . 25 5.4.5.2 Test requirements . 26 5.4.6 Receiver spurious emissions . 26 5.4.6.1 Method of measurement . 26 5.4.6.1.1 Initial conditions . 26 5.4.6.1.2 Procedure . 26 5.4.6.2 Test requirements . 26 5.4.7 Receiver blocking characteristics . 27 5.4.7.1 Method of Measurement . 27 5.4.7.1.1 Initial conditions . 28 5.4.7.1.2 Procedure . 28 5.4.7.2 Test requirements . 28 5.4.8 Receiver Intermodulation characteristics . 28 5.4.8.1 Method of measurement . 28 5.4.8.1.1 Initial conditions . 29 5.4.8.1.2 Procedure . 29 5.4.8.2 Test requirements . 30 5.4.9 Receiver adjacent channel selectivity . 30 5.4.9.1 Method of measurement . 30 5.4.9.1.1 Initial conditions . 30 5.4.9.1.2 Procedure . 30 5.4.9.2 Test requirements . 31 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 32 Annex B (normative): Environmental profile . 34 Annex C (informative): The EN title in the official languages . 35 SIST EN 301 908-20 V5.2.1:2011



ETSI ETSI EN 301 908-20 V5.2.1 (2011-09)5 Annex D (informative): Bibliography . 36 History . 37
SIST EN 301 908-20 V5.2.1:2011



ETSI ETSI EN 301 908-20 V5.2.1 (2011-09)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.2] are summarised in annex A. The present document is part 20 of a multi-part deliverable covering the essential requirements under article 3.2 of Directive 1999/5/EC [i.2] for Base Stations (BS), Repeaters and User Equipment (UE) for IMT cellular networks, as identified below: Part 1: "Introduction and common requirements"; Part 2: "CDMA Direct Spread (UTRA FDD) User Equipment (UE)"; Part 3: "CDMA Direct Spread (UTRA FDD) Base Stations (BS)"; Part 4: "CDMA Multi-Carrier (cdma2000) User Equipment (UE)"; Part 5: "CDMA Multi-Carrier (cdma2000) Base Stations (BS)"; Part 6: "CDMA TDD (UTRA TDD) User Equipment (UE)"; Part 7: "CDMA TDD (UTRA TDD ) Base Stations (BS)"; Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 11: "CDMA Direct Spread (UTRA FDD) (Repeaters)"; Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 13: "Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)"; SIST EN 301 908-20 V5.2.1:2011



ETSI ETSI EN 301 908-20 V5.2.1 (2011-09)7 Part 14: "Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)"; Part 15: "Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD Repeaters)"; Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 18: "E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Stations (BS)"; Part 19: "OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)"; Part 20: "OFDMA TDD WMAN (Mobile WiMAX) TDD Base Stations (BS)"; Part 21: "OFDMA TDD WMAN (Mobile WiMAX) FDD User Equipment (UE)"; Part 22: "OFDMA TDD WMAN (Mobile WiMAX) FDD Base Stations (BS)".
National transposition dates Date of adoption of this EN: 12 September 2011 Date of latest announcement of this EN (doa): 31 December 2011 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 June 2012 Date of withdrawal of any conflicting National Standard (dow): 30 June 2013
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-20 V5.2.1:2011



ETSI ETSI EN 301 908-20 V5.2.1 (2011-09)8 1 Scope The present document applies to the following radio equipment type: • Base stations for IMT-2000 OFDMA TDD WMAN (Mobile WiMAX) operating in TDD mode. This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: OFDMA TDD WMAN Base Station frequency bands Mobile WiMAX Band Class Index IMT-2000 OFDMA TDD WMAN service operating bands Channel Bandwidth 1B 2 300 MHz to 2 400 MHz 5 MHz and 10 MHz
The requirements in the present document apply to both Wide Area Base Stations and Local Area Base Stations unless otherwise stated.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2], (R&TTE Directive) article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Directive 1999/5/EC [i.2] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. [1] ETSI EN 301 908-1 (V5.2.1): "IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements". [2] CEPT/ERC/REC 74-01E (Siófok 1998, Nice 1999, Sesimbra 2002, Hradec Kralove 2005): "Unwanted emissions in the spurious domain". 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. SIST EN 301 908-20 V5.2.1:2011



ETSI ETSI EN 301 908-20 V5.2.1 (2011-09)9 [i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of Harmonized Standards for application under the R&TTE Directive". [i.4] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Recommended approach, and possible limits for measurement uncertainty for the measurement of radiated electromagnetic fields above 1 GHz". [i.5] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction". [i.6] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.7] ITU-R Recommendation SM.329-10 (2003): "Unwanted emissions in the spurious domain". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the R&TTE Directive [i.2] and the following apply: burst: period during which radio waves are intentionally transmitted, preceded and succeeded by periods during which no intentional transmission is made environmental profile: declared range of environmental conditions under which equipment within the scope of the present document is required to be compliant integral antenna: antenna which is declared to be part of the radio equipment by the manufacturer NOTE: Even when equipment with an integral antenna is concerned, it might still be possible to separate the antenna from the equipment usin
...