oSIST prEN 13880-3:2022

SLOVENSKI STANDARD
oSIST prEN 13880-3:2022
01-december-2022
Tesnilne mase za stike, ki se vgrajujejo po vročem postopku - 3. del: Preskusna
metoda za ugotavljanje penetracije in sposobnosti vrnitve v prvotno stanje
Hot applied joint sealants - Part 3: Test method for the determination of penetration and
recovery (resilience)
Heiß verarbeitbare Fugenmassen - Teil 3: Prüfverfahren zur Bestimmung der Kugel-
Penetration und des elastischen Rückstellvermögens
Produits de scellement de joints appliqués à chaud - Partie 3 : Méthode d'essais pour la
détermination de la pénétrabilité et du retour élastique
Ta slovenski standard je istoveten z: prEN 13880-3
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
93.080.20 Materiali za gradnjo cest Road construction materials
oSIST prEN 13880-3:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13880-3:2022

---------------------- Page: 2 ----------------------
oSIST prEN 13880-3:2022


DRAFT
EUROPEAN STANDARD
prEN 13880-3
NORME EUROPÉENNE

EUROPÄISCHE NORM

October 2022
ICS 93.080.20 Will supersede EN 13880-3:2003
English Version

Hot applied joint sealants - Part 3: Test method for the
determination of penetration and recovery (resilience)
Produits de scellement de joints appliqués à chaud - Heiß verarbeitbare Fugenmassen - Teil 3:
Partie 3 : Méthode d'essais pour la détermination de la Prüfverfahren zur Bestimmung der Kugel-Penetration
pénétrabilité et du retour élastique und des elastischen Rückstellvermögens
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 227.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13880-3:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13880-3:2022
prEN 13880-3:2022 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Apparatus . 5
5.1 Penetrometer . 5
5.2 Ball penetration tool . 5
5.3 Water bath . 5
5.4 Sample Tins . 6
5.5 Time recording equipment . 6
6 Preparation and conditioning of the test specimens . 6
7 Test conditions . 6
8 Procedure. 6
9 Precision . 7
10 Test report . 7
Bibliography . 9

2

---------------------- Page: 4 ----------------------
oSIST prEN 13880-3:2022
prEN 13880-3:2022 (E)
European foreword
This document (prEN 13880-3:2022) has been prepared by Technical Committee CEN/TC 207 “Road
materials”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13880-3:2003.
This document is one part of the EN 13880 series of standards, Hot applied joint sealants, which consists
of the following parts:
— Part 1: Test method for the determination of density at 25 °C
— Part 2: Test method for the determination of cone penetration at 25 °C
— Part 3: Test method for the determination of penetration and recovery (resilience)
— Part 4: Test method for the determination of heat resistance - Change in penetration value
— Part 5: Test method for the determination of flow resistance
— Part 6: Method for the preparation of samples for testing
— Part 7: Function testing of joint sealants
— Part 8: Test method for the determination of the change in weight of fuel resistance joint sealants after
fuel immersion
— Part 9: Test method for the determination of compatibility with asphalt pavements
— Part 10: Test method for the determination of adhesion and cohesion following continuous extension
and compression
— Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the
determination of compatibility with asphalt pavements
— Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)
— Part 13: Test method for the determination of the discontinuous extension (adherence test)
3

---------------------- Page: 5 ----------------------
oSIST prEN 13880-3:2022
prEN 13880-3:2022 (E)
1 Scope
This document describes a test method as an indicator both for the penetration resistance (hardness)
and elastic recovery after de-loading (resilience) of hot applied joint sealants according to EN 14188-1 at
25 °C using a standard penetrometer fitted with a ball penetration tool.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced documen
...