SIST EN ISO 22526-2:2022
(Main)Plastics - Carbon and environmental footprint of biobased plastics - Part 2: Material carbon footprint, amount (mass) of CO2 removed from the air and incorporated into polymer molecule (ISO 22526-2:2020)
Plastics - Carbon and environmental footprint of biobased plastics - Part 2: Material carbon footprint, amount (mass) of CO2 removed from the air and incorporated into polymer molecule (ISO 22526-2:2020)
This document defines the material carbon footprint as the amount (mass) of CO2 removed from the air and incorporated into plastic, and specifies a determination method to quantify it.
This document is applicable to plastic products, plastic materials and polymer resins that are partly or wholly based on biobased constituents.
Kunststoffe - Kohlenstoff- und Umweltbilanz von biobasierten Kunststoffen - Teil 2: Kohlenstoffbilanz des Materials, Menge (Masse) des aus der Luft entfernten und in das Polymermolekül integrierten CO2 (ISO 22526 2:2020)
Plastiques - Empreinte carbone et environnementale des plastiques biosourcés - Partie 2: Empreinte carbone des matériaux, quantité (masse) de CO2 captée dans l'air et incorporée dans les molécules de polymères (ISO 22526-2:2020)
Le présent document définit l’empreinte carbone du matériau comme étant la quantité (masse) de CO2 captée dans l’air et incorporée dans un plastique, et il spécifie une méthode de détermination pour la quantifier.
Le présent document s’applique aux produits plastiques, aux matériaux plastiques et aux résines polymères qui sont fabriqués partiellement ou entièrement à partir de constituants biosourcés.
Polimerni materiali - Ogljični in okoljski odtis polimernih materialov na biološki osnovi - 2. del: Ogljični odtis materialov, količina (masa) CO2, odstranjena iz zraka in vključena v molekulo polimera (ISO 22526-2:2020)
Ta dokument opredeljuje ogljični odtis materiala kot količino (maso) CO2, odstranjeno iz zraka in dodano polimernemu materialu, ter določa metodo določanja za njegovo količinsko opredelitev.
Ta dokument se uporablja za izdelke iz polimernih materialov, polimerne materiale in polimerne smole, ki so delno ali v celoti osnovani na bioloških sestavinah.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 22526-2:2022
01-januar-2022
Polimerni materiali - Ogljični in okoljski odtis polimernih materialov na biološki
osnovi - 2. del: Ogljični odtis materialov, količina (masa) CO2, odstranjena iz zraka
in vključena v molekulo polimera (ISO 22526-2:2020)
Plastics - Carbon and environmental footprint of biobased plastics - Part 2: Material
carbon footprint, amount (mass) of CO2 removed from the air and incorporated into
polymer molecule (ISO 22526-2:2020)
Kunststoffe - Kohlenstoff- und Umweltbilanz von biobasierten Kunststoffen - Teil 2:
Kohlenstoffbilanz des Materials, Menge (Masse) des aus der Luft entfernten und in das
Polymermolekül integrierten CO2 (ISO 22526 2:2020)
Plastiques - Empreinte carbone et environnementale des plastiques biosourcés - Partie
2: Empreinte carbone des matériaux, quantité (masse) de CO2 captée dans l'air et
incorporée dans les molécules de polymères (ISO 22526-2:2020)
Ta slovenski standard je istoveten z: EN ISO 22526-2:2021
ICS:
13.020.40 Onesnaževanje, nadzor nad Pollution, pollution control
onesnaževanjem in and conservation
ohranjanje
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 22526-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 22526-2:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 22526-2:2022
EN ISO 22526-2
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2021
EUROPÄISCHE NORM
ICS 13.020.40; 83.080.01
English Version
Plastics - Carbon and environmental footprint of biobased
plastics - Part 2: Material carbon footprint, amount (mass)
of CO2 removed from the air and incorporated into
polymer molecule (ISO 22526-2:2020)
Plastiques - Empreinte carbone et environnementale Kunststoffe - Kohlenstoff- und Umweltbilanz von
des plastiques biosourcés - Partie 2: Empreinte biobasierten Kunststoffen - Teil 2: Kohlenstoffbilanz
carbone des matériaux, quantité (masse) de CO2 des Materials, Menge (Masse) des aus der Luft
captée dans l'air et incorporée dans les molécules de entfernten und in das Polymermolekül integrierten
polymères (ISO 22526-2:2020) CO2 (ISO 22526 2:2020)
This European Standard was approved by CEN on 8 November 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22526-2:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 22526-2:2022
EN ISO 22526-2:2021 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 22526-2:2022
EN ISO 22526-2:2021 (E)
European foreword
The text of ISO 22526-2:2020 has been prepared by Technical Committee ISO/TC 61 "Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 22526-2:2021
by Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2022, and conflicting national standards shall be
withdrawn at the latest by May 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 22526-2:2020 has been approved by CEN as EN ISO 22526-2:2021 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 22526-2:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 22526-2:2022
INTERNATIONAL ISO
STANDARD 22526-2
First edition
2020-03
Plastics — Carbon and environmental
footprint of biobased plastics —
Part 2:
Material carbon footprint, amount
(mass) of CO removed from the
2
air and incorporated into polymer
molecule
Plastiques — Empreinte carbone et environnementale des plastiques
biosourcés —
Partie 2: Empreinte carbone des matériaux, quantité (masse) de CO
2
captée dans l'air et incorporée dans les molécules de polymères
Reference number
ISO 22526-2:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 22526-2:2022
ISO 22526-2:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 22526-2:2022
ISO 22526-2:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions, symbols and abbreviated terms . 1
3.1 Terms and definitions . 1
3.2 Symbols . 2
3.3 Abbreviated terms . 2
4 Application . 2
5 Material carbon footprint . 2
5.1 Principle . 2
5.2 Determination of the biobased carbon content . 2
5.3 Determination or calculation of biobased carbon content on a mass base . 2
5.4 Calculation of the amount (mass) of CO removed from the air and incorporated
2
into 1 kg of the polymer . 3
5.4.1 Calculation from biobased carbon content on a mass base . 3
5.4.2 Calculation from biobased synthetic polymer content . 3
Annex A (informative) Calculation of the amount of CO removed from the air for each polymer .4
2
Annex B (informative) Value of equivalent emissions in typical activities .7
Bibliography . 8
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 22526-2:2022
ISO 22526-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO
...
SLOVENSKI STANDARD
oSIST prEN ISO 22526-2:2021
01-september-2021
Polimerni materiali - Ogljični in okoljski odtis polimernih materialov na biološki
osnovi - 2. del: Ogljični odtis materialov, količina (masa) CO2, odstranjena iz zraka
in vključena v molekulo polimera (ISO 22526-2:2020)
Plastics - Carbon and environmental footprint of biobased plastics - Part 2: Material
carbon footprint, amount (mass) of CO2 removed from the air and incorporated into
polymer molecule (ISO 22526-2:2020)
Kunststoffe - CO2- und ökologischer Fußabdruck von biobasierten Kunststoffen - Teil 2:
Werkstoff-CO2-Fußabdruck, Menge (Masse) des aus der Luft entfernten und in das
Polymermolekül integrierten CO2 (ISO 22526-2:2020)
Plastiques - Empreinte carbone et environnementale des plastiques biosourcés - Partie
2: Empreinte carbone des matériaux, quantité (masse) de CO2 captée dans l'air et
incorporée dans les molécules de polymères (ISO 22526-2:2020)
Ta slovenski standard je istoveten z: prEN ISO 22526-2
ICS:
13.020.40 Onesnaževanje, nadzor nad Pollution, pollution control
onesnaževanjem in and conservation
ohranjanje
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 22526-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 22526-2:2021
---------------------- Page: 2 ----------------------
oSIST prEN ISO 22526-2:2021
INTERNATIONAL ISO
STANDARD 22526-2
First edition
2020-03
Plastics — Carbon and environmental
footprint of biobased plastics —
Part 2:
Material carbon footprint, amount
(mass) of CO removed from the
2
air and incorporated into polymer
molecule
Plastiques — Empreinte carbone et environnementale des plastiques
biosourcés —
Partie 2: Empreinte carbone des matériaux, quantité (masse) de CO
2
captée dans l'air et incorporée dans les molécules de polymères
Reference number
ISO 22526-2:2020(E)
©
ISO 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO 22526-2:2021
ISO 22526-2:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 22526-2:2021
ISO 22526-2:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions, symbols and abbreviated terms . 1
3.1 Terms and definitions . 1
3.2 Symbols . 2
3.3 Abbreviated terms . 2
4 Application . 2
5 Material carbon footprint . 2
5.1 Principle . 2
5.2 Determination of the biobased carbon content . 2
5.3 Determination or calculation of biobased carbon content on a mass base . 2
5.4 Calculation of the amount (mass) of CO removed from the air and incorporated
2
into 1 kg of the polymer . 3
5.4.1 Calculation from biobased carbon content on a mass base . 3
5.4.2 Calculation from biobased synthetic polymer content . 3
Annex A (informative) Calculation of the amount of CO removed from the air for each polymer .4
2
Annex B (informative) Value of equivalent emissions in typical activities .7
Bibliography . 8
© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 22526-2:2021
ISO 22526-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 14,
Environmental aspects.
A list of all parts in the ISO 22526 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 22526-2:2021
ISO 22526-2:2020(E)
Introduction
Increased use of biomass resources for m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.