ISO/TS 23782:2024

Technical
Specification
ISO/TS 23782
First edition
Requirements for large-scale test
2024-07
methods to represent fire threats to
people in different fire scenarios
Exigences relatives aux méthodes d'essai à grande échelle pour
représenter les dangers dus au feu pour les personnes dans
différents scénarios d'incendie
Reference number
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General principles . 2
4.1 Compromised tenability .2
4.2 Fire profile .2
5 Significance and use . 3
5.1 Application of large-scale test.3
5.2 Fire test scenario .3
5.3 Suitable test rig .4
6 Suitable test rig design . 4
6.1 General .4
6.2 Non-flaming fires in a small room .5
6.3 Small smouldering or flaming fire in a small room .5
6.3.1 General .5
6.3.2 Suitable test rig .5
6.4 Small fire in a room with the door opened .5
6.4.1 General .5
6.4.2 Suitable test rig .5
6.5 Small smouldering or flaming fire in a small room with window partially opened .6
6.5.1 General .6
6.5.2 Suitable test rig .6
6.6 Small smouldering or flaming fire in a small room with large exterior vents opened .6
6.6.1 General .6
6.6.2 Suitable test rig .7
6.7 Flaming fire in a large space with a large floor and high ceiling .7
6.7.1 General (Scenario 1) .7
6.7.2 Suitable test rig — Scenario 1 .7
6.7.3 Scenario 2 .7
6.7.4 Suitable test rig — Scenario 2 .7
7 Preparation of test . 7
7.1 Occupants of interest .7
7.2 Test rig .8
7.3 Ignition source .8
7.4 Fuel .9
7.5 Instrumentation .9
7.5.1 General .9
7.5.2 Sampling and analysis of toxic fire effluents .9
8 Measurements .10
8.1 Heat .10
8.1.1 General .10
8.1.2 Convective effect .11
8.1.3 Radiant effect .11
8.2 Smoke obscuration .11
8.3 Toxic gas .11
8.4 Equivalence ratio .11
8.5 Mass loss .11
8.6 Miscellaneous .11
9 Data analysis and interpretation .12

iii
9.1 General . 12
9.2 Repeatability of test . 12
9.3 Reproducibility of test . 12
10 Reporting requirements .13
Annex A (informative) Fire classification and typical characteristics . 14
Annex B (informative) Suitable test rig with instrumentation: example designs and
configurations . 17
Bibliography . 19

iv
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to imp
...