ISO 3547-6:2007

SLOVENSKI STANDARD
SIST ISO 3547-6:2008
01-julij-2008
Drsni ležaji - Zvite puše - 6. del: Merjenje notranjega premera
Plain bearings - Wrapped bushes - Part 6: Checking the inside diameter
Gleitlager - Gerollte Buchsen - Teil 6: Prüfung des Innendurchmessers
Paliers lisses - Bagues roulées - Partie 6: Contrôle du diamètre intérieur
Ta slovenski standard je istoveten z: ISO 3547-6:2007
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 3547-6:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

INTERNATIONAL ISO
STANDARD 3547-6
First edition
2007-10-01

Plain bearings — Wrapped bushes —
Part 6:
Checking the inside diameter
Paliers lisses — Bagues roulées —
Partie 6: Contrôle du diamètre intérieur




Reference number
ISO 3547-6:2007(E)
©
ISO 2007

---------------------- Page: 2 ----------------------

ISO 3547-6:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 3 ----------------------

ISO 3547-6:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Symbols and units. 2
4 Method of checking . 2
5 Test equipment . 2
6 Procedure . 6
Bibliography . 7

© ISO 2007 – All rights reserved iii

---------------------- Page: 4 ----------------------

ISO 3547-6:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Inter-
national Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted according to the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3547-6 was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 5, Quality
analysis and assurance.
This part of ISO 3547 cancels and replaces ISO 12307-2:2000, which has been technically revised.
ISO 3547 consists of the following parts, under the general title Plain bearings — Wrapped bushes:
⎯ Part 1: Dimensions
⎯ Part 2: Test data for outside and inside diameters
⎯ Part 3: Lubrication holes, grooves and indentations
⎯ Part 4: Materials
⎯ Part 5: Checking the outside diameter
⎯ Part 6: Checking the inside diameter
⎯ Part 7: Measurement of wall thickness of thin-walled bushes

iv © ISO 2007 – All rights reserved

---------------------- Page: 5 ----------------------

INTERNATIONAL STANDARD ISO 3547-6:2007(E)

Plain bearings — Wrapped bushes —
Part 6:
Checking the inside diameter
1 Scope
The part of ISO 3547 specifies, following ISO 12301, the checking of the inside diameter of wrapped bushes
(see ISO 3547-2:2006, method C) and describes the necessary checking methods and measuring equipment.
Wrapped bushes in the free condition are flexible, but after insertion they adapt largely to the shape of the
housing bore due to th
...