ISO 3547-6:2020

SLOVENSKI STANDARD
SIST ISO 3547-6:2020
01-november-2020
Drsni ležaji - Zvite puše - 6. del: Kontrola notranjega premera
Plain bearings - Wrapped bushes - Part 6: Checking the inside diameter
Ta slovenski standard je istoveten z: ISO 3547-6:2020
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 3547-6:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 3547-6:2020

---------------------- Page: 2 ----------------------
SIST ISO 3547-6:2020
INTERNATIONAL ISO
STANDARD 3547-6
Second edition
2020-05
Plain bearings — Wrapped bushes —
Part 6:
Checking the inside diameter
Reference number
ISO 3547-6:2020(E)
©
ISO 2020

---------------------- Page: 3 ----------------------
SIST ISO 3547-6:2020
ISO 3547-6:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 3547-6:2020
ISO 3547-6:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 1
5 Method of checking . 2
6 Test equipment. 2
6.1 Ring gauge . 2
6.2 Plug gauge . 3
6.3 Three-point measuring instrument . 4
6.4 Requirements for measuring equipment . 5
6.5 Measuring errors. 5
7 Procedure. 5
Bibliography . 6
© ISO 2020 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 3547-6:2020
ISO 3547-6:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 5,
Quality analysis and assurance.
This second edition cancels and replaces the first edition (ISO 3547-6:2007), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Clause 2 has been updated;
— Figures 1, 2 and 3 have been updated;
— Clause 3 (Terms and definitions) has been added;
— Figure 4 has been implemented;
— Clauses 5 and 6 have been updated.
A list of all parts in the ISO 3547 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s natio
...