ISO 19323:2018

INTERNATIONAL ISO
STANDARD 19323
First edition
2018-09
Timber structures — Joist hangers —
Test methods
Structures en bois — Étriers à solive — Méthodes d'essai
Reference number
©
ISO 2018
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Materials . 2
5.1 Timber . 2
5.2 Concrete or masonry . 3
5.3 Fasteners . 3
5.4 Joist hangers . 3
6 Sampling . 3
7 Test apparatus . 4
7.1 Testing machine . 4
7.2 Displacement transducers . 4
8 Tests . 4
8.1 General . 4
8.2 Vertical load test . 4
8.2.1 Test setup . 4
8.2.2 Test procedure . 7
8.2.3 Test report . 8
8.3 Tension load test . 8
8.3.1 Test setup . 8
8.3.2 Test procedure . 9
8.3.3 Test report . 9
8.4 Torsional load test .11
8.4.1 Test setup .11
8.4.2 Test procedure .13
8.4.3 Calculation of torsional moment and rotation .13
8.4.4 Test report .14
8.5 Cyclic vertical load test.15
8.5.1 Test setup .15
8.5.2 Test procedure .15
8.5.3 Test report .15
Bibliography .17
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 165, Timber structures.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved

Introduction
Joist hangers are an integral part of timber constructions in that they provide a necessary means of
connection between timber elements and also between timber elements and other materials such as
metal, concrete and masonry. Hangers are made predominantly from light gauge steel sheet which is
electrolytically or hot-dipped galvanised and which is bent into a formed three-dimensional element
– mostly U-shaped to allow for a bearing seat and lateral support to the joist. For high corrosion zones,
stainless steel is often used in lieu of galvanised steel sheet. Hangers may also be made from welded
steel plates.
To provide a suitable connection, the joist hangers are capable of transferring forces in a range of
directions depending on the make-up of the joint. Fasteners (e.g. nails, screws, bolts and dowels and
proprietary fasteners) are inserted in the pre-punched or pre-drilled holes of the joist hanger plates
(bearing seat, face and top plate) to secure the connection between the joint elements. The purpose of
this document is to provide standard test procedures that can be used to determine the strength of a
joint incorporating a joist hanger.
INTERNATIONAL STANDARD ISO 19323:2018(E)
Timber structures — Joist hangers — Test methods
1 Scope
This document provides standard test methods for determining the vertical load, axial load and
torsional moment capacity as well as deflection characteristics of preformed three-dimensional joist
hangers that are used primarily for securing one timber member to another (the header can be concrete
or masonry). The joist hangers primarily transfer vertical loads from the supported member to the
supporting member, but they can also be required to transfer axial loads from the supported member
to the supporting member.
NOTE 1 Structural steel sections can also be substituted as the header, but are not covered in this document.
NOTE 2 One secondary mechanism to be considered is the effect of rotation of the supported member about
its longitudinal axis on the joist hanger.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1920-4, Testing of concrete — Part 4: Strength of hardened concrete
ISO 1920-6, Testing of concrete — Part 6: Sampling, preparing and testing of concrete cores
ISO 7500-1, Metallic materials — Calibration and verification of static uniaxial testing machines — Part 1:
Tension/compression testing machines — Calibration and verification of the force-measuring system
ISO 8970, Timber structures — Testing of joints made with mechanical fasteners — Requirements for
wood density
ISO 9652-4, Masonry — Part 4: Test methods
ISO 10984-1, Timber structures — Dowel-type fasteners — Part 1: Determination of yield moment
ISO 10984-2, Timber structures — Dowel-type fasteners — Part 2: Determination of embedding strength
ISO 13061-1, Physical and mechanical properties of wood — Test methods for small clear wood specimens —
Part 1: Determination of moisture content for physical and mechanical tests
ISO 13061-2, Physical and mechanical properties of wood — Test methods for small clear wood specimens —
Part 2: Determination of density for physical and mechanical tests
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
supporting member
header
member supporting a joist hanger
3.2
supported member
joist
bending or a tension member supported by a joist hanger
3.3
joist hanger
metal device, usually cold-formed from light-gauge steel sheet, used to transfer loads from a joist to a
header member or wall in building construction
Note 1 to entry: Face-mounted joist hangers contact the side surface of the header and do not contact the top of
the header. Top-mounted hangers are joist hangers that contact the side and top surface of the header.
Note 2 to entry: Joist hangers may also be constructed from welded steel plate. Joist hangers may also fit within a
vertical recess in the joist (concealed). Joist hangers may also consist of two interacting brackets, one connected
to the header and one connected to the end of the joist.
4 Symbols
P mean of the maximum loads achieved in the vertical load test
t
5 Materials
5.1 Timber
5.1.1 The timber shall be selected in accordance with ISO 8970.
NOTE When timber is selected in accordance with ISO 8970 the measured load carrying capacities need not
be modified, provided that the coefficient of variation of the density of the selected timber reflects the natural
variation of density.
5.1.2 For the determination of the vertical load strength, tensile strength (along the line of the
supported member axis) and torsional strength of the joist hanger, the timber shall be sufficiently strong
for failure to occur in the joist hanger and/or its fixings.
5.1.3 The supported member timber width shall match the manufacturer’s specified width for the joist
hanger being tested.
5.1.4 The timber used as joist and headers shall be consistent with the timber being used in
construction, i.e. sawn timber or structural composite lumber (SCL) or glue laminated timber.
Installation (including web stiffeners, filler blocks and backer blocks for I-joists) shall also replicate the
manufacturer’s specifications.
5.1.5 The joist and the header members for the specimens shall be cut so that the area where the joist
hanger is located are free from knots, local grain disturbance, fissures (such as shakes, checks and splits)
and wane. Elsewhere, the members shall be free from major defects that can lead to premature failure in
the timber.
5.1.6 The moisture content of the timber shall be determined in accordance with ISO 13061-1, and its
density in accordance with ISO 13061-2. When measuring the moisture content of manufactured wood
products, care shall be taken to avoid the effect of adhesives or other non-wood material on readings.
2 © ISO 2018 – All rights reserved

5.1.7 The moisture content at the time of testing shall be greater than 11 %.
NOTE For certain investigations, other moisture conditions can be appropriate.
5.1.8 The identity of the species shall, if necessary, be confirmed by a botanical examination.
5.1.9 A minimum period of seven days shall elapse between the assembly and testing of the test
specimens to allow for fibre relaxation.
5.2 Concrete or masonry
5.2.1 If the header is replaced with concrete, a minimum of three concrete test cylinders shall be
prepared, stored and cured in accordance with ISO 1920-6 from the same batch of concrete used in the
joist hanger test specimen. Cylinders shall be tested in accordance with ISO 1920-4 within 24 h of the
test of the joist hanger.
5.2.2 If the header is replaced with masonry, the compressive strength of the masonry shall be
determined by the prism test method in accordance with ISO 9652-4.
5.3 Fasteners
5.3.1 When nail and screw fasteners are used with the joist hanger, fasteners from the same
manufacturer’s lot as were used in the joist hanger test specimen shall be sampled to determine the
fastener bending yield strength in accordance with ISO 10984-1.
5.3.2 When bolt and dowel fasteners are used with the joist hanger, fasteners from the same
manufacturer’s lot as were used in the joist hanger test specimen shall be sampled to determine the
fastener embedding strength in accordance with ISO 10984-2.
5.3.3 Fasteners that secure the joist hanger to concrete or masonry header shall be appropriate for
the header material and shall have sufficient strength to ensure that the failure under any of the loading
conditions tested herein shall be in the joist hanger only. The fastener shall be selected so that the
stiffness of the fastener does not affect the global evaluation of the stiffness of the joist hanger in any test.
5.4 Joist hangers
5.4.1 The sizes of joist hangers used for the various tests shall be selected from the range of sizes
produced by the joist hanger manufacturer in such a way that the strength values for all sizes can be
obtained by interpolation, provided the interpolation is based on at least three data points and where
only one variable changes (such as the header depth and number of fasteners). Appropriate regression
shall be used and reported.
5.4.2 When tested in accordance with ISO 5002 or an equivalent standard, the mechanical properties
(tensile strength, yield stress, elongation and hardness) of the test coil metal shall meet the requirements
for the specified structural grade of steel for the joist hanger manufacture.
5.4.3 If the manufacturer’s installation instructions require that the joist hangers be free of oil or any
substance that can alter the hanger performance in service, they shall be washed in solvent before they
are used in the tests.
6 Sampling
The number of joist hangers tested shall be sufficient to fabricate a minimum of five test specimens for
each combination of joist hanger size and load condition.
7 Test apparatus
7.1 Testing machine
The testing machine shall be capable of operation at a constant rate of motion of the movable crosshead
or a constant rate of loading. The force-measuring device shall be calibrated in accordance with
ISO 7500-1.
7.2 Displacement transducers
All tests shall use a displacement transducer on each side of the joist to measure the relative movements
between the supported member and header. Devices used for this purpose shall be calibrated and have
an accuracy of ±0,02 mm.
8 Tests
8.1 General
8.1.1 The support and restraint conditions shall be those specified by the manufacturer and shall reflect
the declared intended use. In the absence of manufacturer-supplied support and restraint conditions the
test specimens shall be supported and restrained as described in the test methods below.
8.1.2 The manufacturer shall specify any assumptions regarding the preparation of the supporting and
supported members.
EXAMPLE Requirements for pre-drilling holes, tolerance on the hole diameter and any special installation/
maintenance provisions (e.g. re-tightening bolts).
8.2 Vertical load test
8.2.1 Test setup
8.2.1.1 Test specimens consisting of a length of joist supported by a joist hanger attached to a header
shall be constructed as shown in Figure 1.
NOTE The header can be either fully restrained against rotation or simply supported as specified by the
manufacturer.
8.2.1.2 The header shall have a length sufficient to provide support against lateral translation at a
distance of at least one and a half times the depth of the header or two times the depth of the joist hanger,
whichever is the larger, from the centreline of the joist.
8.2.1.3 The joist length shall be sufficient to allow the application of the load at a distance of two times
the depth of the joist from the front face of the header and the distance from the load application point to
the remote support shall be six times the joist depth.
8.2.1.4 Reinforcement of the joist member in the area of the load application shall be permitted.
Reinforcement may be required to prevent joist member failure in bending, shear or compression
perpendicular to the grain at the applied load. Wood failure modes, such as joist bending failure and joist
top surface crushing at the load transfer block are unrelated to the performance of the joist hanger and
if such failures occur, the specimen shall be discarded and additional tests undertaken with appropriate
reinforcement included.
4 © ISO 2018 – All rights reserved

8.2.1.5 A minimum clearance of 3 mm shall be provided between the end of the joist and abutting
material, i.e. the header if no hanger section between the header and the joist or any
...