ISO 363-1:2006
(Main)Textile machinery and accessories - Flat steel healds with closed end loops - Part 1: Dimensions of healds manufactured of rolled steel wire
Textile machinery and accessories - Flat steel healds with closed end loops - Part 1: Dimensions of healds manufactured of rolled steel wire
ISO 363-1:2006 specifies the main dimensions of flat steel healds with closed end loops (O-shaped end loops) manufactured of rolled steel wire for use in the textile industry.
Matériel pour l'industrie textile — Lisses en acier plat avec boucles d'extrémités fermées — Partie 1: Dimensions des lisses fabriquées en fils d'acier laminé
L'ISO 363-1:2006 spécifie les dimensions principales des lisses en acier plat avec boucles d'extrémités fermées fabriquées en fils d'acier laminé destinées à être utilisées dans l'industrie textile.
General Information
- Status
- Published
- Publication Date
- 14-Mar-2006
- Current Stage
- 9599 - Withdrawal of International Standard
- Start Date
- 18-Nov-2024
- Completion Date
- 13-Dec-2025
Relations
- Effective Date
- 15-Apr-2008
Overview
ISO 363-1:2006 - Textile machinery and accessories - Flat steel healds with closed end loops - Part 1: Dimensions of healds manufactured of rolled steel wire specifies the principal dimensions and configuration details for flat steel healds (O‑shaped closed end loops) made from rolled steel wire for use in weaving and other textile machinery. This first edition replaces ISO 363:1992 and is intended to ensure interchangeability, compatibility and safe use of healds across equipment and suppliers.
Key topics and requirements
- Scope: Defines the main dimensions of flat steel healds with closed end loops manufactured of rolled steel wire.
- Dimensional data: Provides sizes in millimetres for typical cross‑sections, thread‑eye dimensions and distances between end loops. Typical cross‑section examples include 2.0×0.25 mm, 2.2×0.30 mm, 2.5×0.35 mm and 2.8×0.40 mm. Standard distances between end loops commonly include 280, 330, 380 and 420 mm; thread‑eye sizes are shown in the table (approx. 5.0–6.5 mm depending on cross‑section).
- Heald types: Illustrates straight (SIMPLEX) and cranked (DUPLEX) healds, and identifies end‑loop offset, thread eye orientation (direction of eye open to the right), and other geometric details.
- Ordering options: Notes that healds may be supplied with corrugated end loops at one end and flat loops at the other (recommended for certain automatic drawing‑in machines).
- Manufacturing tolerances: States that slight deviations from the nominal dimensions are permissible for certain manufacturing methods.
- Illustration and table references: Dimensions and notes are given graphically (Figure 1) and in tabular form (Table 1).
Applications and users
ISO 363-1:2006 is directly relevant to:
- Heald manufacturers - for designing and producing flat steel healds to accepted dimensions.
- Textile machinery builders - to ensure compatibility of healds with looms and drawing‑in equipment.
- Weaving mills and textile plants - for procurement specifications, maintenance and replacement of healds.
- Quality assurance and inspection - to verify heald geometry and interchangeability.
- Suppliers and technical buyers - to reference standardized sizes when ordering parts.
Keywords: ISO 363-1:2006, flat steel healds, closed end loops, rolled steel wire, heald dimensions, textile machinery, thread eye, weaving machines.
Related standards
- ISO 363-2 - Part 2: Dimensions of healds manufactured of hardened strip steel (companion document).
- ISO 363:1992 - earlier edition superseded by ISO 363-1:2006.
ISO 363-1:2006 - Textile machinery and accessories -- Flat steel healds with closed end loops
ISO 363-1:2006 - Matériel pour l'industrie textile -- Lisses en acier plat avec boucles d'extrémités fermées
Frequently Asked Questions
ISO 363-1:2006 is a standard published by the International Organization for Standardization (ISO). Its full title is "Textile machinery and accessories - Flat steel healds with closed end loops - Part 1: Dimensions of healds manufactured of rolled steel wire". This standard covers: ISO 363-1:2006 specifies the main dimensions of flat steel healds with closed end loops (O-shaped end loops) manufactured of rolled steel wire for use in the textile industry.
ISO 363-1:2006 specifies the main dimensions of flat steel healds with closed end loops (O-shaped end loops) manufactured of rolled steel wire for use in the textile industry.
ISO 363-1:2006 is classified under the following ICS (International Classification for Standards) categories: 59.120.30 - Looms. Weaving machines. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 363-1:2006 has the following relationships with other standards: It is inter standard links to ISO 363:1992. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase ISO 363-1:2006 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 363-1
First edition
2006-03-15
Textile machinery and accessories — Flat
steel healds with closed end loops —
Part 1:
Dimensions of healds manufactured of
rolled steel wire
Matériel pour l'industrie textile — Lisses en acier plat avec boucles
d'extrémités fermées —
Partie 1: Dimensions des lisses fabriquées en fils d'acier laminé
Reference number
©
ISO 2006
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodie
...
NORME ISO
INTERNATIONALE 363-1
Première édition
2006-03-15
Matériel pour l'industrie textile — Lisses
en acier plat avec boucles d'extrémités
fermées —
Partie 1:
Dimensions des lisses fabriquées en fils
d'acier laminé
Textile machinery and accessories — Flat steel healds with closed end
loops —
Part 1: Dimensions of healds manufactured of rolled steel wire
Numéro de référence
©
ISO 2006
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2006
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2006 – Tous droits réservés
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...