ISO 8279:2008

INTERNATIONAL ISO
STANDARD 8279
Third edition
2008-08-01


Aerospace — Nuts, hexagonal, plain,
normal height, normal across flats, with
MJ threads, classifications: 600 MPa (at
ambient temperature)/120 °C, 600 MPa (at
ambient temperature)/235 °C, 900 MPa (at
ambient temperature)/425 °C, 1 100 MPa
(at ambient temperature)/235 °C,
1 100 MPa (at ambient
temperature)/315 °C, 1 100 MPa (at
ambient temperature)/650 °C, 1 210 MPa
(at ambient temperature)/730 °C,
1 250 MPa (at ambient
temperature)/235 °C and 1 550 MPa
(at ambient temperature)/600 °C —
Dimensions
Aéronautique et espace — Écrous hexagonaux ordinaires, hauteur
normale, surplats normaux, à filetages MJ, classifications: 600 MPa
(à température ambiante)/120 °C, 600 MPa (à température
ambiante)/235 °C, 900 MPa (à température ambiante)/425 °C,
1 100 MPa (à température ambiante)/235 °C, 1 100 MPa
(à température ambiante)/315 °C, 1 100 MPa (à température
ambiante)/650 °C, 1 210 MPa (à température ambiante)/730 °C,
1 250 MPa (à température ambiante)/235 °C et 1 550 MPa
(à température ambiante)/600 °C — Dimensions




Reference number
ISO 8279:2008(E)
©
ISO 2008

---------------------- Page: 1 ----------------------
ISO 8279:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2008 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8279:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8279 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 4,
Aerospace fastener systems.
This third edition cancels and replaces the second edition (ISO 8279:1997), which has been technically
revised.
© ISO 2008 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 8279:2008(E)
Introduction
The dimensions specified in this International Standard have been determined to satisfy the requirements of
the procurement specification ISO 9139.

iv © ISO 2008 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 8279:2008(E)


Aerospace — Nuts, hexagonal, pl
...