Plastics — Unsaturated-polyester resins (UP-R) — Part 1: Designation system

Plastiques — Résines de polyesters non saturés (UP-R) — Partie 1: Système de désignation

La présente partie de l'ISO 3672 établit une système de blocs de données pour la désignation des résines de polyesters non saturés (UP-R). Les types d'UP-R sont différenciés les uns des autres par un système de classification basé sur des informations relatives à la résine de base, à d'éventuels charges/matériaux de renforcement (type et teneur), à la méthode de mise en oeuvre prévue, aux propriétés spécifiées en général et à celles utilisées spécifiquement pour les besoins de la désignation (propriétés de désignation). La présente partie de l'ISO 3672 est applicable à tous les types de résines de polyesters non saturés dans leur usage courant qu'elles soient à l'état liquide ou à l'état solide. Le fait que deux résines aient la même désignation n'implique pas qu'elles présentent nécessairement les mêmes performances. La présente partie de l'ISO 3672 ne comporte pas de données sur la conception, les performances ou les conditions de mise en ceuvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en ceuvre particulière. Si de telles caractéristiques supplémentaires sont nécessaires, elles doivent être déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 3672-2, le cas échéant. Pour garantir que la signification des lettres-codes, nombres-codes et chiffres-codes demeure non ambiguë et pour éviter toute contradiction au sein du système, les nouveaux lettres-codes, nombres-codes et chiffres-codes à utiliser dans les blocs de données 1, 2 et 3 doivent être approuvés par les secrétariats de l'ISO/TC 61/SC 1, SC 12 et SC 13 avant utilisation.

Polimerni materiali - Nenasičene poliestrske smole (UP-R) - 1. del: Sistem označevanja

General Information

Status
Published
Publication Date
09-Aug-2000
Current Stage
9093 - International Standard confirmed
Completion Date
04-Sep-2020

Relations

Buy Standard

Standard
ISO 3672-1:2000 - Plastics -- Unsaturated-polyester resins (UP-R)
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3672-1:2001
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 3672-1:2000 - Plastiques -- Résines de polyesters non saturés (UP-R)
French language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3672-1
Second edition
2000-07-15
Plastics — Unsaturated-polyester resins
(UP-R) —
Part 1:
Designation system
Plastiques — Résines de polyesters non saturés (UP-R) —
Partie 1: Système de désignation
Reference number
ISO 3672-1:2000(E)
©
ISO 2000

---------------------- Page: 1 ----------------------
ISO 3672-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3672-1:2000(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Designation system.2
5 Examples of designations .7
© ISO 2000 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3672-1:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 3672 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 3672-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 12, Thermosetting materials.
This second edition cancels and replaces the first edition (ISO 3672:1979), which has been technically revised.
ISO 3672 consists of the following parts, under the general title Plastics — Unsaturated-polyester resins (UP-R):
� Part 1: Designation system
� Part 2: Preparation of test specimens and determination of properties
iv © ISO 2000 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3672-1:2000(E)
Plastics — Unsaturated-polyester resins (UP-R) —
Part 1:
Designation system
1 Scope
1.1 This part of ISO 3672 establishes a data block system for the designation of unsaturated-polyester resins
(UP-R).
1.2 The various types of UP-R are differentiated from each other by a classification system based on information
about the basic polymer parameters, the possible fillers/reinforcements (type and content), the intended method of
processing, any specified properties and those of the specified properties used specifically for designation
purposes (designatory properties).
1.3 This part of ISO 3672 is applicable to all types of unsaturated-polyester resin for normal use in a liquid state
and in a solid state.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 3672 does not provide engineering data, performance data or data on processing
conditions which may be required to specify a material for a particular application and/or method of processing. If
such additional properties are required, they shall be determined in accordance with the test methods specified in
part 2 of this International Standard, if suitable.
1.5 To ensure that code-letters and code-numbers remain unambiguous and to avoid conflicts within the system,
any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the
secretariats of ISO/TC 61/SC 1, SC 12 and SC 13.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 3672. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 3672 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 472:1999, Plastics — Vocabulary.
ISO 1043-1:1997, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics.
ISO 1043-2:2000, Plastics — Symbols and abbreviated terms — Part 2: Fillers and reinforcing materials.
1)
ISO 2535:— , Plastics — Unsaturated-polyester resins — Measurement of gel time at ambient temperature.
1) To be published. (Revision of ISO 2535:1997)
© ISO 2000 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 3672-1:2000(E)
ISO 3219:1993, Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of
viscosity using a rotational viscometer with defined shear rate.
ISO 3672-2:2000, Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and
determination of properties.
ISO 14848:1998, Plastics — Unsaturated-polyester resins — Determination of reactivity at 130 °C.
3 Terms and definitions
For the purposes of this part of ISO 3672, the terms and definitions given in ISO 472 and ISO 3672-2 apply, plus
the following:
3.1
UP-R
the abbreviation for unsaturated-polyester resins
4 Designation system
4.1 General
The designation system defined in this part of ISO 3672 is based on the following standardized pattern:
Designation
Identity block
Individual-item block
Description
ISO
block
Data Data Data Data Data
Standard
block block block block block
1 2 3 4 5
The designation consists of an optional description block, reading “R” (resin), and an identity block comprising the
International Standard number and an individual-item block. For unambiguous designation, the individual-item
block is subdivided into five data blocks comprising the following information:
Data block 1: Marking block
Item 1: Identification of the basic polymer by its symbol, in accordance with ISO 1043-1;
Item 2: Nature of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2;
Item 3: Form of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2;
Item 4: Nominal content of the designatory reinforcement materials or fillers, in accordance with Table 1.
Data block 2: Method of processing
Method of processing for which the unsaturated-polyester resin is intended, designated in accordance with
Table 2.
Data block 3: Properties
Item 1: Specified properties, in accordance with Table 3;
2 © ISO 2000 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 3672-1:2000(E)
Item 2: Designatory property No. 1 — visco
...

SLOVENSKI STANDARD
SIST ISO 3672-1:2001
01-junij-2001
3ROLPHUQLPDWHULDOL1HQDVLþHQHSROLHVWUVNHVPROH 835 GHO6LVWHP
R]QDþHYDQMD
Plastics -- Unsaturated-polyester resins (UP-R) -- Part 1: Designation system
Plastiques -- Résines de polyesters non saturés (UP-R) -- Partie 1: Système de
désignation
Ta slovenski standard je istoveten z: ISO 3672-1:2000
ICS:
83.080.10 Duromeri Thermosetting materials
SIST ISO 3672-1:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 3672-1:2001

---------------------- Page: 2 ----------------------

SIST ISO 3672-1:2001
INTERNATIONAL ISO
STANDARD 3672-1
Second edition
2000-07-15
Plastics — Unsaturated-polyester resins
(UP-R) —
Part 1:
Designation system
Plastiques — Résines de polyesters non saturés (UP-R) —
Partie 1: Système de désignation
Reference number
ISO 3672-1:2000(E)
©
ISO 2000

---------------------- Page: 3 ----------------------

SIST ISO 3672-1:2001
ISO 3672-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 3672-1:2001
ISO 3672-1:2000(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Designation system.2
5 Examples of designations .7
© ISO 2000 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 3672-1:2001
ISO 3672-1:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 3672 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 3672-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 12, Thermosetting materials.
This second edition cancels and replaces the first edition (ISO 3672:1979), which has been technically revised.
ISO 3672 consists of the following parts, under the general title Plastics — Unsaturated-polyester resins (UP-R):
� Part 1: Designation system
� Part 2: Preparation of test specimens and determination of properties
iv © ISO 2000 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 3672-1:2001
INTERNATIONAL STANDARD ISO 3672-1:2000(E)
Plastics — Unsaturated-polyester resins (UP-R) —
Part 1:
Designation system
1 Scope
1.1 This part of ISO 3672 establishes a data block system for the designation of unsaturated-polyester resins
(UP-R).
1.2 The various types of UP-R are differentiated from each other by a classification system based on information
about the basic polymer parameters, the possible fillers/reinforcements (type and content), the intended method of
processing, any specified properties and those of the specified properties used specifically for designation
purposes (designatory properties).
1.3 This part of ISO 3672 is applicable to all types of unsaturated-polyester resin for normal use in a liquid state
and in a solid state.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 3672 does not provide engineering data, performance data or data on processing
conditions which may be required to specify a material for a particular application and/or method of processing. If
such additional properties are required, they shall be determined in accordance with the test methods specified in
part 2 of this International Standard, if suitable.
1.5 To ensure that code-letters and code-numbers remain unambiguous and to avoid conflicts within the system,
any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the
secretariats of ISO/TC 61/SC 1, SC 12 and SC 13.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 3672. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 3672 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 472:1999, Plastics — Vocabulary.
ISO 1043-1:1997, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics.
ISO 1043-2:2000, Plastics — Symbols and abbreviated terms — Part 2: Fillers and reinforcing materials.
1)
ISO 2535:— , Plastics — Unsaturated-polyester resins — Measurement of gel time at ambient temperature.
1) To be published. (Revision of ISO 2535:1997)
© ISO 2000 – All rights reserved 1

---------------------- Page: 7 ----------------------

SIST ISO 3672-1:2001
ISO 3672-1:2000(E)
ISO 3219:1993, Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of
viscosity using a rotational viscometer with defined shear rate.
ISO 3672-2:2000, Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and
determination of properties.
ISO 14848:1998, Plastics — Unsaturated-polyester resins — Determination of reactivity at 130 °C.
3 Terms and definitions
For the purposes of this part of ISO 3672, the terms and definitions given in ISO 472 and ISO 3672-2 apply, plus
the following:
3.1
UP-R
the abbreviation for unsaturated-polyester resins
4 Designation system
4.1 General
The designation system defined in this part of ISO 3672 is based on the following standardized pattern:
Designation
Identity block
Individual-item block
Description
ISO
block
Data Data Data Data Data
Standard
block block block block block
1 2 3 4 5
The designation consists of an optional description block, reading “R” (resin), and an identity block comprising the
International Standard number and an individual-item block. For unambiguous designation, the individual-item
block is subdivided into five data blocks comprising the following information:
Data block 1: Marking block
Item 1: Identification of the basic polymer by its symbol, in accordance with ISO 1043-1;
Item 2: Nature of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2;
Item 3: Form of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2;
Item 4: Nominal content of the designatory reinforcement materials or fillers, in accordance
...

NORME ISO
INTERNATIONALE 3672-1
Deuxième édition
2000-07-15
Plastiques — Résines de polyesters
non saturés (UP-R) —
Partie 1:
Système de désignation
Plastics — Unsaturated-polyester resins (UP-R) —
Part 1: Designation system
Numéro de référence
ISO 3672-1:2000(F)
©
ISO 2000

---------------------- Page: 1 ----------------------
ISO 3672-1:2000(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifiéà moins que l'ordinateur employéà cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la créationduprésent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2000
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-aprèsouducomité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Imprimé en Suisse
ii © ISO 2000 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3672-1:2000(F)
Sommaire Page
Avant-propos.iv
1 Domaine d'application.1
2Références normatives .1
3Termesetdéfinitions.2
4Système de désignation.2
5 Exemples de désignations.7
© ISO 2000 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 3672-1:2000(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiéeaux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude aledroit de fairepartie ducomité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
L’attention est appelée sur le fait que certains des éléments delaprésente partie de l’ISO 3672 peuvent faire
l’objet de droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
La Norme internationale ISO 3672-1 a étéélaboréepar le comité technique ISO/TC 61, Plastiques, sous-comité
SC 12, Matériaux thermodurcissables.
Cette deuxième édition annule et remplace la première édition (ISO 3672-1:1979), dont elle constitue une révision
technique.
L'ISO 3672 comprend les parties suivantes, présentées sous le titre général Plastiques — Résines de polyesters
non saturés(UP-R):
� Partie 1: Système de désignation
� Partie 2: Préparation des éprouvettes et détermination des propriétés
iv © ISO 2000 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 3672-1:2000(F)
Plastiques — Résines de polyesters non saturés(UP-R) —
Partie 1:
Système de désignation
1 Domaine d'application
1.1 La présente partie de l'ISO 3672 établit une système de blocs de données pour la désignation des résines
de polyesters non saturés(UP-R).
1.2 Les types d’UP-R sont différenciés les uns des autres par un système de classification basé sur des
informations relatives à la résine de base, à d'éventuels charges/matériaux de renforcement (type et teneur), à la
méthode de mise en œuvre prévue, aux propriétésspécifiées en général et à celles utilisées spécifiquement pour
les besoins de la désignation (propriétésdedésignation).
1.3 La présente partie de l’ISO 3672 est applicable à tous les types de résines de polyesters non saturés dans
leur usage courant qu'elles soient à l’état liquide ou à l’état solide.
1.4 Le fait que deux résines aient la même désignation n'implique pas qu'elles présentent nécessairement les
mêmes performances. La présente partie de l'ISO 3672 ne comporte pas de données sur la conception, les
performances ou les conditions de mise en œuvre qui peuvent être exigées pour spécifier un matériau pour une
application et/ou une méthodedemise en œuvre particulière. Si de telles caractéristiques supplémentaires sont
nécessaires, elles doivent être déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 3672-2, le
cas échéant.
1.5 Pour garantir que la signification des lettres-codes, nombres-codes et chiffres-codes demeure non ambiguë
et pour éviter toute contradiction auseindusystème, les nouveaux lettres-codes, nombres-codes et chiffres-codes
à utiliser dans les blocs de données 1, 2 et 3 doivent être approuvéspar lessecrétariats de l’ISO/TC 61/SC 1,
SC 12 et SC 13 avant utilisation.
2Références normatives
Les documents normatifs suivants contiennent des dispositions qui, par suite de la référence qui y est faite,
constituent des dispositions valables pour la présente partie de l'ISO 3672. Pour les références datées, les
amendements ultérieurs ou les révisions de ces publications ne s’appliquent pas. Toutefois, les parties prenantes
aux accords fondés sur la présentepartiedel'ISO3672sont invitées à rechercher la possibilité d'appliquer les
éditions les plus récentes des documents normatifs indiqués ci-après. Pour les références non datées, la dernière
édition du document normatif en référence s’applique. Les membres de l'ISO et de la CEI possèdent le registre des
Normes internationales en vigueur.
ISO 472:1999, Plastiques — Vocabulaire.
ISO 1043-1:1997, Plastiques — Symboles et abréviations — Partie 1: Polymères de base et leurs caractéristiques
spéciales.
ISO 1043-2:2000, Plastiques — Symboles et abréviations — Partie 2: Charges et matériaux de renforcement.
© ISO 2000 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 3672-1:2000(F)
1)
ISO 2535:— , Plastiques — Résines de polyesters non saturés — Mesurage du temps de gel à température
ambiante.
ISO 3219:1993, Plastiques — Polymères/résines à l'état liquide en émulsion ouendispersion — Détermination de
la viscosité au moyen d'un viscosimètre rotatif à gradient de vitesse de cisaillement défini.
ISO 3672-2:2000, Plastiques — Résines de polyesters non saturés(UP-R) — Partie 2: Préparation des
éprouvettes et détermination des propriétés.
ISO 14848:1998, Plastiques — Résines de polyesters non saturés — Déterminationde laréactivitéà 130 °C.
3 Termes et définitions
Pour les besoins de la présente partie de l’ISO 3672, les termes et définitions donnésdansl’ISO 472 et dans
l'ISO 3672-2 s’appliquent, conjointement avec la suivante:
3.1
UP-R
abréviationderésines de polyesters non saturés
4Système de désignation
4.1 Généralités
Le système de désignation défini dans la présente partie de l’ISO 3672 est basé sur le modèle normalisé suivant:
Désignation
Bloc d'identité
Bloc «objet particulier»
Bloc
descripteur
Norme ISO
Bloc de Bloc de Bloc de Bloc de Bloc de
données 1 données 2 données 3 données 4 données 5
La désignation consiste en un bloc descriptif facultatif, intitulé«R» (résine), un bloc d'identité comprenant le
numéro de la Norme Internationale et un bloc «objet particulier». Pour une désignation non ambiguë,lebloc «objet
particulier» est subdivisé en cinq blocs de données comprenant les informations suivantes:
Bloc de données 1: Bloc relatif au marquage
Élément 1: Identification du polymère de base par son symbole, conformément à l'ISO 1043-1;
Élément 2: Nature des matériaux de renforcement ou charges pour la désignation, conformément à
l’ISO 1043-2;
Élément 3: Présentation des matériaux de renforcement ou charges pour la désignation, conformément à
l’ISO 1043-2;
Élément 4: Teneur nominale des matériaux de renforcement ou charge pour la désignation, conformément
au Tableau 1.
1) À publier. (Révision de l’ISO 2535:1997)
2 © ISO 2000 – Tous droits réservés

---------------------- Page: 6 ----------------------
ISO 3672-1:2000(F)
Bloc de données 2: Méthode de mise en œuvre
Méthode de mise en œuvre prévue pour la résine de polyesters non saturés, désignéeconformément au
Tableau 2.
Bloc de données 3: Propriétés
Élément 1: Propriétésspécifiées, conformément au Tableau 3.
Élément 2: Propriété de désignation n° 1 — viscositéà 23 °Cdéterminée conformémen
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.