ISO 7206-4:2010/Amd 1:2016
(Amendment)Implants for surgery — Partial and total hip joint prostheses — Part 4: Determination of endurance properties and performance of stemmed femoral components — Amendment 1
Implants for surgery — Partial and total hip joint prostheses — Part 4: Determination of endurance properties and performance of stemmed femoral components — Amendment 1
Implants chirurgicaux — Prothèses partielles et totales de l'articulation de la hanche — Partie 4: Détermination des propriétés d'endurance et des performances des tiges fémorales — Amendement 1
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 7206-4
Third edition
2010-06-15
AMENDMENT 1
2016-03-15
Implants for surgery — Partial and
total hip joint prostheses —
Part 4:
Determination of endurance
properties and performance of
stemmed femoral components
AMENDMENT 1
Implants chirurgicaux — Prothèses partielles et totales de
l’articulation de la hanche —
Partie 4: Détermination des propriétés d’endurance et des
performances des tiges fémorales
AMENDEMENT 1
Reference number
ISO 7206-4:2010/Amd.1:2016(E)
©
ISO 2016
---------------------- Page: 1 ----------------------
ISO 7206-4:2010/Amd.1:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7206-4:2010/Amd.1:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This d
...
DRAFT AMENDMENT
ISO 7206-4:2010/DAM 1
ISO/TC 150/SC 4 Secretariat: BSI
Voting begins on: Voting terminates on:
2015-09-15 2015-12-15
Implants for surgery — Partial and total hip joint
prostheses —
Part 4:
Determination of endurance properties and performance
of stemmed femoral components
AMENDMENT 1
Implants chirurgicaux — Prothèses partielles et totales de l’articulation de la hanche —
Partie 4: Détermination des propriétés d’endurance et des performances des tiges fémorales
AMENDEMENT 1
ICS: 11.040.40
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 7206-4:2010/DAM 1:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015
---------------------- Page: 1 ----------------------
ISO 7206-4:2010/DAM 1:2015(E) ISO 7206-4:2010/DAM 1
Contents Page
Foreword .iv
1 Replace figure A.6 with the figure below .1
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
© ISO 2015 – All rights reserved iii
----------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.