IEC 60695-10-2:2003/COR1:2006
(Corrigendum)Corrigendum 1 - Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test
Corrigendum 1 - Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test
Corrigendum 1 - Essais relatifs aux risques du feu - Partie 10-2: Chaleurs anormales - Essai à la bille
General Information
Relations
Standards Content (Sample)
Publication 60695-10-2 de la CEI IEC Publication 60695-10-2
(Deuxième édition – 2003) (Second edition – 2003)
Fire hazard testing –
Essais relatifs aux risques du feu –
Part 10-2: Abnormal heat – Ball pressure test
Partie 10-2: Chaleurs anormales – Essai à la bille
CORRIGENDUM 1
Page 12 Page 13
Paragraphe 7.1 Subclause 7.1
Premier alinéa, deuxième phrase, au lieu First paragraph, second sentence, instead
de: of:
L’étuve et le support d’éprouvette doivent The heating oven and test specimen
être maintenus à la température d’essai support shall be maintained at the test
pendant 24 h ou jusqu'à ce que les temperature for 24 h or until thermal
...
This May Also Interest You
- Standard4 pagesEnglish and French languagesale 15% off
IEC 60695-2-11:2021 specifies a test method on an end product. It is intended to simulate the effects of thermal stresses produced by an electrically heated source to represent a fire hazard. This test method is used to check that, under defined test conditions, an end product exposed to an electrically heated source has either a limited ability to ignite or, if it ignites, a limited ability to propagate flame. However, the fire hazard analysis, the flammability aspects and the flame spreading to other products are not covered by this document. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. This publication is to be read in conjunction with IEC 60695-2-10. This third edition cancels and replaces the second edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) Numerous terms and definitions relevant to this document have been added to Clause 3.
- Standard48 pagesEnglish languagesale 15% off
- Standard32 pagesEnglish and French languagesale 15% off
IEC 60695-5-1:2021 provides guidance on the following:
a) general aspects of corrosion damage test methods;
b) methods of measurement of corrosion damage;
c) consideration of test methods;
d) relevance of corrosion damage data to hazard assessment.
This basic safety publication is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. This standard is to be read in conjunction with IEC TS 60695-5-2.
This third edition cancels and replaces the second edition, published in 2002, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) References to IEC TS 60695-5-3 (withdrawn in 2014) have been removed.
b) References to IEC 60695-1-1 are now to its replacements: IEC 60695-1-10 and IEC 60695-1-11.
c) ISO/TR 9122-1 has been revised by ISO 19706.
d) Table 1 has been updated.
e) References to ISO 11907-2 and ISO 11907-3 have been removed.
f) Terms and definitions have been updated.
g) Text in 6.4 has been updated.
h) Bibliographic references have been updated.
- Standard62 pagesEnglish languagesale 15% off
- Standard38 pagesEnglish and French languagesale 15% off
IEC 60695-7-2:2021 gives a brief summary of the test methods that are in common use in the assessment of the toxicity of fire effluent. It includes special observations on their relevance to real fire scenarios and gives recommendations on their use.
It advises which tests provide toxic potency data that are relevant to real fire scenarios, and which are suitable for use in fire hazard assessment and fire safety engineering.
The list of test methods is not to be considered exhaustive.
This summary cannot be used in place of published standards which are the only valid reference documents.
This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.
This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision.
The main changes with respect to the previous edition are listed below:
– New text in the introduction;
– New text in the scope;
– Clause 2 has been updated;
– Many terms and definitions in Clause 3 reproduced from ISO 13943 have been deleted. Other terms and definitions have been added.
– New text in Subclauses 4.3 and 4.4;
– New text in Subclause 6.1;
– References to IEC 60695-7-50 and -51 (now withdrawn) have been removed;
– Reference to DEF STAN 07-247 has been added;
– Details of ISO/TS 19021 have been added;
– Details of EN 17084 have been added;
– New text added concerning ISO/TS 19700;
– New text added concerning the IMO FTP toxicity test;
– New Subclause 7.1 has been added;
– The Annex in Edition1 has been replaced by new Clause 8;
– The bibliography has been updated.
- Standard90 pagesEnglish and French languagesale 15% off
IEC 60695-2-10:2021 specifies the glow-wire apparatus and common test procedure to simulate the effects of thermal stresses which may be produced by heat sources such as glowing elements or overloaded resistors, for short periods, in order to assess the fire hazard by a simulation technique. The test procedure described in this document is a common test procedure intended for the small-scale tests in which a standardized electrically heated wire is used as a source of ignition. It is a common part of the test procedures applied to end products and to solid electrical insulating materials or other solid combustible materials. A detailed description of each particular test procedure is given in IEC 60695-2-11, IEC 60695-2-12 and IEC 60695-2-13. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. This standard is to be used in conjunction with IEC 60695-2-11, IEC 60695-2-12, and IEC 60695-2-13. This third edition cancels and replaces the second edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) New terms and definitions with regards to times and durations have been added to Clause 3.
b) Previous Annex A of Equipment manufacturers and suppliers has been deleted.
c) Annex A (previous Annex B) for ignition and flaming observations has been changed from informative to normative.
d) New Annex C has been added, which visualizes times and durations, and gives examples for the behaviour of specimens, and how to evaluate them.
The contents of the corrigendum of January 2024 have been included in this copy.
- Standard75 pagesEnglish languagesale 15% off
- Standard46 pagesEnglish and French languagesale 15% off
IEC 60695-2-12:2021 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for flammability testing to determine the glow-wire flammability index (GWFI). GWFI is the highest temperature, determined during this standardized procedure, at which the tested material does not ignite or, if it does, extinguishes within 30 s after removal of the glow-wire and is not totally consumed; and molten drips, if they occur, do not ignite the wrapping tissue. This test method is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire ignition temperature (GWIT) test method for materials, IEC 60695-2-13, can then be used in a preselection process in accordance with IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of IEC 60695-2-11. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. This publication is to be read in conjunction with IEC 60695-2-10. This third edition cancels and replaces the second edition published in 2010 and Amendment 1:2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) New terms and definitions with regards to times and durations have been added to Clause 3, with an effect on the application of the test method.
- Standard40 pagesEnglish languagesale 15% off
- Standard26 pagesEnglish and French languagesale 15% off
IEC 60695-9-2:2021 presents a summary of published test methods that are used to determine the surface spread of flame of electrotechnical products or materials from which they are formed.
It represents the current state of the art of the test methods and, where available, includes special observations on their relevance and use.
The list of test methods is not to be considered exhaustive, and test methods that were not developed by the IEC are not to be considered as endorsed by the IEC unless this is specifically stated.
This summary cannot be used in place of published standards which are the only valid reference documents.
This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and
ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.
This International Standard is to be used in conjunction with IEC 60695-1.
This second edition cancels and replaces the first edition of IEC 60695-9-2 published in 2014. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Updated introduction
b) Updated normative references
c) Updated terms and definitions
d) New Subclauses 4.1 and 4.2
e) Reference to fire stages as defined in ISO 19706 (Table 1)
f) New sub-division of tests into the following subclauses:
4.3 Small-scale fire tests
4.4 Medium and intermediate-scale fire tests
4.5 Intermediate and large-scale fire tests for cables
4.6 Real-scale fire tests for cables
g) Updated text in parts of Clause 4
h) Addition of the following test methods:
IEC TS 60695-11-21
IEC 60684-2:2011, Clause 26
ISO 3582
ISO 9772
ISO 9773
ISO 12992
ISO 21367
i) New Clause 5 and Table 4 giving an overview of test methods
j) Deletion of all the Annexes
k) Updated bibliography
- Standard84 pagesEnglish and French languagesale 15% off
IEC 60695-2-13:2021 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for ignitability testing to determine the glow-wire ignition temperature (GWIT). The GWIT is the temperature which is 25 K (or 30 K) higher than the maximum test temperature, determined during this standardized procedure, at which the tested material does not ignite, or sustained flaming combustion does not occur for a time longer than 5 s for any single flame event and the specimen is not totally consumed. This test is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire flammability index (GWFI) test method for materials, IEC 60695-2-12, can then be used in a preselection process in accordance with IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of IEC 60695-2-11. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. This publication is to be read in conjunction with IEC 60695-2-10. This third edition cancels and replaces the second edition published in 2010 and Amendment 1:2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- New terms and definitions with regards to times and durations have been added to Clause 3, with an effect on the application of the test method.
- Standard38 pagesEnglish languagesale 15% off
- Standard25 pagesEnglish and French languagesale 15% off
IEC 60695-6-1:2021 gives guidance on:
a) the optical measurement of obscuration of smoke;
b) general aspects of optical smoke test methods;
c) consideration of test methods;
d) expression of smoke test data;
e) the relevance of optical smoke data to hazard assessment.
This basic safety publication focusing on safety guidance is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.
This third edition cancels and replaces the second edition of IEC 60695-6-1 published in 2005 and Amendment 1:2010. It constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- References to IEC TS 60695-6-30 (withdrawn in 2016) have been removed.
- References to IEC TS 60695-6-31 (withdrawn in 2016) have been removed.
- References to ISO 5659-2 have been inserted.
- The scope contains some additional text.
- Terms and definitions have been updated.
- Subclause 3.2 has been updated.
- Subclause 7.1 has been updated.
It has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51. This International Standard is to be used in conjunction with IEC 60695-6-2.
- Standard101 pagesEnglish languagesale 15% off
- Standard65 pagesEnglish and French languagesale 15% off
IEC TS 60695-11-40:2021 presents a general characterization of small-scale test flames and associated confirmatory tests based on copper block calorimetry. Guidance is presented for the selection of critical parameters in confirmatory test designs.
This basic safety publication is intended for use by technical committee in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.
This second edition cancels and replaces the first edition published in 2002. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) former Clause 4 split into updated/rearranged new Clause 4 and Clause 5;
b) Table 1 updated and moved to new Clause 4;
c) former Clause 5 transformed to Clause 6;
d) former Clause 6 transformed to Clause 7;
e) former Clause7, Clause 8 and Clause 9 combined into an updated/rearranged new Annex A; and
f) all figures were updated.
This Technical Specification is to be used in conjunction with IEC 60695-11-2, IEC 60695-11-3, IEC 60695-11-4 and IEC 60695-11-5.
- Technical specification20 pagesEnglish languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.