IEC 62906-5-6:2020
(Main)Laser displays - Part 5-6: Measuring methods for optical performance of projection screens
Laser displays - Part 5-6: Measuring methods for optical performance of projection screens
IEC 62906-5-6:2020 (E) specifies the standard measurement conditions and measuring methods for determining the optical performance of a projection screen in terms of its photometric characteristics, including screen gain and speckle contrast, from different viewing directions. These methods are only applied for the case in which the projection screen and a laser projector are integrated and used with a fixed configuration as a set to create a real image. Both front and rear projection screens, with a flat surface, are included. This document excludes projection screens which are classified as optically see-through screens, including head-up displays.
General Information
Standards Content (Sample)
IEC 62906-5-6 ®
Edition 1.0 2020-04
INTERNATIONAL
STANDARD
colour
inside
Laser displays –
Part 5-6: Measuring methods for optical performance of projection screens
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 62906-5-6 ®
Edition 1.0 2020-04
INTERNATIONAL
STANDARD
colour
inside
Laser displays –
Part 5-6: Measuring methods for optical performance of projection screens
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 31.260 ISBN 978-2-8322-8233-5
– 2 – IEC 62906-5-6:2020 © IEC 2020
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, and abbreviated terms . 6
3.1 Terms and definitions . 6
3.2 Abbreviated terms . 7
4 Standard measuring conditions . 7
4.1 General . 7
4.2 Environmental conditions . 7
4.3 Power supply . 7
4.4 Warm-up time . 7
4.5 Measurement coordinate system . 8
4.6 Darkroom conditions . 8
4.7 Measuring facilities . 8
5 Installation and adjustment of the DUT . 9
5.1 Placement of the projector and the screen . 9
5.2 Focusing of the projector . 9
5.3 Standard projector setup conditions . 10
5.4 Standard image measurement locations . 10
6 Signal patterns . 11
7 Measuring methods . 12
7.1 Screen gain . 12
7.1.1 Purpose . 12
7.1.2 Measuring equipment and conditions . 12
7.1.3 Measuring methods . 13
7.2 Screen gain directivity and half-gain angle . 13
7.2.1 Purpose . 13
7.2.2 Measuring conditions . 14
7.2.3 Measuring methods . 14
7.3 Screen gain uniformity . 14
7.3.1 Purpose . 14
7.3.2 Measuring conditions . 15
7.3.3 Measuring methods . 15
7.4 Angular characteristics of speckle contrast . 15
7.4.1 Purpose . 15
7.4.2 Measuring conditions . 15
7.4.3 Measuring methods . 16
Annex A (informative) Screen colour shift . 17
A.1 Purpose . 17
A.2 Measuring conditions . 17
A.3 Measuring methods . 17
Annex B (informative) Screen directivity using a Fresnel lens . 18
Annex C (informative) Angular characteristics of speckle contrast with different
screens . 20
Bibliography . 22
Figure 1 – Coordinate system for projection direction and viewing direction . 8
Figure 2 – Example of image pattern with horizontal size H and vertical size V used for
alignment . 10
Figure 3 – Standard measurement locations on the screen (nine measurement points) . 11
Figure 4 – Example of DUT setup . 11
Figure 5 – Full screen patterns . 11
Figure 6 – Measuring geometry of screen gain . 13
Figure 7 – Viewing direction measurement in both horizontal and vertical directions . 14
Figure 8 – Measuring geometry of speckle contrast with changing viewing direction . 16
Figure B.1 – Directivity of the screen under different setups . 18
Figure C.1 – Optical configuration for speckle contrast measurement with different
viewing directions . 20
Figure C.2 – Angular characteristics of speckle contrast obtained from different screen
and different de-speckle conditions . 20
– 4 – IEC 62906-5-6:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LASER DISPLAYS –
Part 5-6: Measuring methods for optical
performance of projection screens
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62906-5-6 has been prepared by IEC technical committee 110:
Electronic displays.
The text of this International Standard is based on the following documents:
FDIS Report on voting
10/1187/FDIS 110/1198/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 62906 series, published under the general title Laser displays, can
be found on the IEC website.
Future standards in this series will carry the new general title as cited above. Titles of existing
standards in this series will be updated at the time of the next edition.
The committee has decided that the contents of this document will remain unchanged until the
stability date
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.